How to Put Text on a Curve in Procreate
StyleFrame Team6 min read
Procreate has no text-on-path feature, so you curve text there by bending it manually. The fastest route is Transform > Warp with Advanced Mesh. Liquify's Push mode gives a looser, painterly bend, and placing letters one by one along a circle guide gives the most control for badges and logos. All three methods rasterize the text, so duplicate the text layer first.
Why Procreate Doesn't Curve Text Natively
Procreate's text tool is a typesetting layer on top of a raster painting app. Illustrator and Photoshop let you type directly onto a path, and Procreate offers nothing comparable. Users have been asking for text on a path and font arching on the Procreate forum, and the community answer is consistent: Procreate lacks the vector machinery, so you either deform pixels or move to a vector app.
For motion work this matters because the curved lettering you build in Procreate is a flat bitmap. You can't retype it later, and its sharpness depends on your canvas size. Plan for that before you start.
Prep: Set Up the Text Before You Bend It
Doing these steps first saves most of the pain later.
- Create the text. Tap Actions (wrench) > Add > Add Text, then type. Drag the blue end nodes to keep the phrase on one line.
- Choose the font and tracking. Pick your font in the text menu. Under Design, raise kerning slightly. Bending compresses letters on the inside of a curve, so a little extra spacing keeps them from colliding.
- Duplicate the layer. Warp and Liquify rasterize text. Keep a hidden copy of the live text layer so you can fix a typo and redo the bend.
- Work large. Bending stretches pixels. A larger canvas and larger type leave more room before softness shows.
- Draw a guide. Add a new layer under the text and sketch the curve you're aiming for. Draw an arc with a mono-line brush, hold at the end of the stroke, and tap Edit Shape to adjust its nodes until it's symmetrical.
For centering, open Actions > Canvas, turn on Drawing Guide, and tap Edit Drawing Guide. Push the grid size to its maximum and the central horizontal and vertical lines become visible, so you can align text and arcs to the true center of the canvas.
Method 1: Warp With Advanced Mesh
Warp is the best default for gentle arcs, banners, and rainbow-style text.
- Select the text layer and tap the Transform tool.
- Choose Warp from the bottom toolbar.
- Tap Advanced Mesh. This gives you a denser grid of control points than the default.
- Drag the mesh down or up so the baseline follows your arc guide. You can drag any part of the mesh, not just the nodes.
- For symmetrical shapes, keep the node positions mirrored left to right. Work from the center outward.
- Compare the result to the guide, nudge individual nodes, and tap Transform again to commit.
Strengths: quick, predictable, and easy to reshape in small increments. Weaknesses: letters tilt and distort rather than rotate cleanly, so tight curves look stretched. Keep arcs shallow, or split a long line into two shorter warps.
Method 2: Liquify (Push)
Liquify behaves like pushing wet paint. It suits expressive, hand-lettered looks where perfect geometry isn't the goal.
- Select the text layer.
- Tap Adjustments > Liquify.
- Choose Push in the bottom toolbar.
- Set brush size relative to your text. Too small and you only bend part of a word. Too large and you drag neighboring letters along with it.
- Enable the brush cursor under Actions > Prefs so you can see the brush outline.
- Make strokes in the direction you want the pixels to travel. You're moving existing letters, not drawing the curve.
Strengths: organic results, good for wavy or irregular shapes. Weaknesses: hard to gauge how much you're bending, and it's easy to distort letterforms unevenly. Undo often and work in short strokes.
Method 3: Circle Guides and Manual Letter Placement
For round badges, seals, and logos with text hugging the top and bottom of a circle, Warp rarely gives clean results. Place each letter by hand.
Build the guide
- On a new layer, draw a circle with a mono-line brush and hold at the end of the stroke until it snaps to a shape. Use a second finger on the canvas to constrain it to a true circle, and size it before you lift.
- Size it to touch the edge of your design, and align it to the canvas center using the drawing guide lines.
- Duplicate the circle and shrink it. The gap between the two circles should match your letter height, so they act as baseline and cap line.
- Group both circles and lower the group's opacity so the guides don't dominate.
Place the letters
- Type your text. For manual placement, use a separate text layer or separate letters so each can be rotated independently.
- Move each letter to its position in the ring and use Transform to rotate it so its baseline is tangent to the guide circle.
- Work from the top center outward in both directions to keep spacing even.
- For text on the bottom of the circle, flip your thinking: letters should read left to right, so their tops point toward the center of the circle rather than away from it.
- Check optical spacing by eye. Letters near a curve need slightly different gaps than they do on a straight line.
This also works for hand lettering. You can draw it on a straight line and then bend it, or letter directly along the guide if that feels natural.
Strengths: the cleanest geometry, and full control of spacing per letter. Weaknesses: slow, and every edit means re-placing letters.
Which Method Should You Use?
Common Problems and Fixes
- Blurry edges after bending. Start from a larger canvas or larger text. If you need to scale up afterward, do it deliberately rather than stretching repeatedly.
- Uneven curves. Use your guide layer and compare at full screen. Asymmetry is easier to spot when you toggle the text layer on and off.
- Squashed letters on tight arcs. Increase kerning before warping, or switch to manual placement.
- Can't edit the wording. Keep that hidden duplicate of the live text layer and redo the bend.
When to Leave Procreate for Live Text on a Path
If you need text that stays editable, use a vector tool. Illustrator offers type on a path, and Affinity Designer has a text-on-path option, though community users describe its handling as fussy. A common workflow is to set the layout in a vector app, import it into Procreate as a guide, then paint over it.
Quick Recap
- Procreate can't set text on a path natively, so you deform it with Warp, Liquify, or manual placement.
- Duplicate the text layer first. Every bending method rasterizes it.
- Use Warp with Advanced Mesh for arcs, Liquify for organic shapes, and circle guides for badges.
- For live, editable text on a curve, use Illustrator or Affinity Designer.
- Export finished lettering with transparency and carry it into your motion pipeline.