How to Put Opacity Down on Procreate
StyleFrame Team6 min read
To lower opacity in Procreate, open the Layers panel, tap the "N" next to the layer name, and drag the opacity slider left. A faster route is to tap the layer with two fingers and slide left on the screen. To make a brush paint more transparently, drag the lower slider on the Sidebar down. Layer opacity can be changed repeatedly without damaging your paint, while opacity applied to a selection is committed once you leave the mode.
What "opacity" means in Procreate
Opacity is how visible pixels are. At 100% they are fully solid, and at 50% you see through them halfway. Procreate lets you control this at three levels: the brush, the whole layer, and a selected area. Each one answers a different problem, so pick the right one before you start dragging sliders.
- Brush opacity changes how strong each new stroke is as you paint.
- Layer opacity changes how visible everything already on a layer is.
- Selection opacity changes the visibility of only the selected pixels on a layer.
Method 1: Lower layer opacity with the N button
This is the most common approach and the one that shows a numeric readout.
- Tap the Layers icon (two overlapping squares) at the top right.
- Find the layer you want to change.
- Tap the small letter to the right of the layer name. It reads "N" by default, for Normal blend mode.
- A panel opens with blend modes and an opacity slider at the top. Drag the slider left to lower opacity, right to raise it.
The percentage appears beside the slider, so you can match values precisely. This is the better method when you need a repeatable number, such as a 35% pencil sketch under inked line work.
Method 2: Two-finger tap on the layer
For fewer taps:
- Open the Layers panel.
- Tap the target layer with two fingers at the same time. An opacity bar appears at the top of the canvas.
- Slide a finger or Apple Pencil left to reduce opacity, right to increase it.
You work on one layer at a time this way. If the layer list scrolls instead of opening the slider, your two-finger touch is probably being read as a scroll. Tap more crisply, with both fingers landing together, or switch to the N button method.
Method 3: Adjustments menu
The Adjustments menu also has an Opacity tool.
- Select the layer you want to change.
- Tap Adjustments, then Opacity.
- Slide left and right anywhere on the canvas to change the value. A bar at the top shows the current percentage.
- Use the buttons at the bottom to cancel, undo, redo, or reset your changes.
This route is useful when you want undo, redo, and reset controls while you experiment, since those buttons sit right in the interface.
How to commit or cancel the change
A common frustration: after sliding opacity down, there is no obvious "accept" button, and touching the canvas with your Apple Pencil keeps changing the opacity instead of drawing.
The reason is that no drawing tool is active while you are in the adjustment mode, so any swipe adjusts opacity. To commit the change, select a tool such as a brush, smudge, or eraser. Tapping the Adjustments icon again also commits it. If you would rather discard what you did, tap Cancel before you leave the mode.
Lowering brush opacity
To make strokes more transparent rather than altering existing paint:
- Pick a brush.
- Find the sliders on the left Sidebar. The lower one controls opacity.
- Drag it down to decrease opacity and up to increase it.
Building up a soft shadow with several light strokes is a classic use. If your brush still looks too faint even with the slider at maximum, check pressure settings. Many brushes respond to Apple Pencil pressure, so light pressure can make strokes look more transparent than the slider suggests. Check your Apple Pencil pressure settings if that is happening.
A clipping mask is a useful companion here. Paint on a layer clipped to the layer beneath, and your strokes stay inside the shape below instead of spilling outside it. That gives you controlled, partially transparent shading without erasing edges.
Lowering opacity on just part of a layer
If you only want to fade one area:
- Open Selections and choose a selection method.
- Make your selection.
- Open Layers and tap the layer containing the paint with two fingers.
- Slide left on the canvas to reduce the opacity of the selected area.
Unlike full-layer opacity, this is a destructive operation. Once you exit the mode, the change is applied to the pixels. You can undo immediately, but you cannot revisit and re-tune it later. If you might want to change your mind, duplicate the layer first, or move the area onto its own layer and use layer opacity instead.
Choosing between opacity methods
As a rule, prefer layer-level opacity wherever you can. It stays editable, which matters once a project grows past a handful of layers.
Why this matters for motion and VFX work
Procreate often supplies assets for After Effects projects: hand-drawn textures, character elements, matte paintings, storyboard frames, and animatic sketches. Opacity decisions made in Procreate affect what you receive in your composition.
A few habits keep your handoff clean:
- Keep fades on layer opacity, not baked into paint. If a smoke wisp sits at 40% layer opacity, you can raise or drop it later, or recreate the value in After Effects. Destructive selection opacity locks the look in.
- Separate elements by layer. One element per layer lets you animate each element's opacity independently in your compositor.
- Verify the export. Export a layered file, bring it into After Effects, and check that layer opacity and blend modes arrived as you expect. If a look matters, compare it against a flattened export. When something is off, flatten that layer or export it individually.
- Use a hidden reference layer. Lower a reference to around 30% for tracing, then hide it before export so it does not appear in your assets.
Quick troubleshooting
- Slider is greyed out or missing: make sure you tapped the layer's N button, not the visibility checkbox next to it.
- Pencil changes opacity instead of drawing: you are still in adjustment mode. Select a brush or eraser.
- Strokes look too faint at 100% brush opacity: check Apple Pencil pressure response.
- Two-finger tap scrolls the layer list: tap with both fingers at the same instant, or use the N button.
- Opacity change cannot be edited later: it was applied to a selection. Undo it and redo it with layer opacity on a separate layer.
Summary
Lowering opacity in Procreate takes seconds once you know the entry points. Use the Sidebar slider for brushes, the N button or a two-finger tap for layers, and the selection method for partial fades. Commit by choosing a tool, and prefer layer-level opacity so your work stays adjustable. Keeping elements on separate layers also makes the handoff to After Effects or Nuke much smoother.