How to Put a Video in Procreate
StyleFrame Team7 min read
To put a video in Procreate, save the clip to the Files app, open the Procreate Gallery, tap Import, and pick the file. Procreate turns it into a new animation canvas where every frame becomes a layer. Importing straight from the Photos app has been unreliable on some versions, so Files is the safer route. Keep clips short and match the canvas frame rate to the source, because layer limits cap how much footage a canvas can hold.
What Procreate Does When You Import a Video
Procreate doesn't treat video as a single clip on a timeline. It splits the footage into individual frames and stacks them as layers, one layer per frame, inside an animation-enabled canvas. Animation Assist, Procreate's timeline tool, then reads those layers as the frame sequence.
This has three consequences:
- Frame count equals layer count. A longer clip or higher frame rate means more layers, and Procreate limits how many layers a canvas can hold.
- Resolution matters. Larger frames can make a canvas heavier, so keeping resolution modest helps.
- Procreate is a drawing tool here, not an editor. You can paint over footage, rotoscope, and add hand-drawn elements. Trimming, color work, and conforming belong in your editing or compositing app beforehand.
If you come from After Effects or Premiere Pro, think of the imported video as a ready-made image sequence you can paint on.
Prepare the Clip Before You Import
A few minutes of prep in your editor saves most import problems.
- Trim to the shot you need. Cut the clip to the exact range you plan to draw on. Handles you won't use only cost you layers.
- Check the frame rate. Note the source frame rate (24 fps, for example) so you can match it in Procreate afterward.
- Reduce the resolution if needed. A 4K master is rarely useful as a rotoscoping base on a tablet. Export a lower-resolution proxy, such as 1920×1080 or smaller, and plan to rebuild the final at full resolution in your compositing app.
- Export a standard format. Stick to a common, widely supported video format and skip exotic codecs.
- Move it to the iPad. AirDrop, iCloud Drive, or a cable transfer all work. Make sure the file lands in the Files app, or in Photos if you want to test that route.
Method 1: Import From the Files App (Most Reliable)
This is the more reliable method, including when videos won't appear in the Photos picker.
- Save or move the video into the Files app. Either a general folder or a folder inside Procreate's area works.
- Open Procreate and stay in the Gallery. Don't open a canvas.
- Tap Import at the top right.
- Browse to the video in Files and tap it.
- Procreate imports the clip automatically.
You can also start from Files: find the clip, tap Share, and choose the Procreate icon. The result is the same.
Method 2: Import From Photos
On versions where it works, you can pull a clip from your camera roll directly into Procreate:
- Go into Procreate's photo options.
- Choose Photo and browse to the clip in your camera roll.
- If the video appears, you'll see a frame strip along the top and a play button for previewing.
- Tap Use, and Procreate imports the frames as layers in a new canvas.
If your videos don't show in the picker, or are grayed out when you use "Insert a file," it's a reported bug that may still exist on some versions. Don't spend time debugging your files. Switch to Method 1.
Set the Frame Rate to Match Your Source
Imported footage can play at the wrong speed at first. The animation canvas has its own frame rate setting, and it may not match the clip's original.
- Make sure Animation Assist is on.
- Open the Animation Assist settings.
- Set the frames per second to the same value as your source clip.
If you shot or rendered at 24 fps and Procreate is set to a different value, playback will feel too slow or too fast. Fix this before you draw a single stroke, because timing mistakes carry into everything you add.
Onion skinning also appears automatically once you're in Animation Assist. Adjust the number of frames and the opacity so the ghosting helps rather than clutters.
Draw on Top of the Footage
Because each frame is a layer, drawing on the footage follows a specific pattern.
- Add a new layer above the frame you're working on. Don't paint on the video layer itself unless you want to alter the footage.
- Group the video layer and your drawing layer together. In Procreate's animation model, each group is one frame. Grouping a frame with its overlay makes both appear as a single frame on the timeline. This is slightly tedious, but it's how you add rotoscoping linework without breaking the sequence.
For a clip of any length, this means you often finish a shot in short sections. Rotoscope a few seconds, export, then continue with the next segment rather than loading the whole shot at once.
Layer Limits and Practical Workarounds
Procreate limits how many layers a canvas can hold. A longer clip can run into that limit quickly, and you may find the import is constrained or the canvas becomes slow.
Ways to stay within limits:
- Cut the shot into segments of a few seconds each and import them separately.
- Lower the resolution of the proxy.
- Drop the frame rate if the work is stylized (for example, animating on twos) and then interpolate in your compositing app.
- Flatten or merge finished frames to free up layers.
- Work only on key shots. Use Procreate for the hand-drawn passes and let After Effects handle everything else.
Get the Result Back Into Your Pipeline
Once the drawing is done, export your animation from Procreate's Share options. Choose a format your compositing app accepts. An image sequence is often preferred for compositing because each frame stays separate, while a video file works for quick review.
Bring the exported frames into After Effects, Nuke, or Blender, and match the frame rate in the composition or project settings. Place them over the original plate and apply color, blending, and finishing there. Keep the full-resolution source in your compositing app so the Procreate pass acts as a stylized overlay, not the final pixels.
Troubleshooting Common Problems
The video doesn't appear in Photos. Use the Files import route. Move the clip to Files and import from the Gallery.
The video is grayed out in "Insert a file." Same fix. Use Import from the Gallery instead of from inside a canvas.
Playback is too slow or too fast. Match the canvas frames-per-second to the source in Animation Assist settings.
The import is truncated or the canvas is sluggish. Shorten the clip, reduce resolution, or split it into segments.
Drawing layers appear as separate frames. Group each video frame with its drawing layer so they share one frame on the timeline.
The exported animation looks softer than the original. Rebuild the final in your compositing app, using the Procreate pass as an overlay on the full-resolution plate, or upscale the result.
Quick Recap
- Trim and export a short clip in a standard format, at a reduced resolution if needed.
- Move it to the Files app.
- In the Procreate Gallery, tap Import and select the clip.
- Enable Animation Assist and match the frame rate to the source.
- Draw on new layers, grouping each with its video frame.
- Export your animation and finish in After Effects, Nuke, or your tool of choice.
The process is simple, but the limits are real. Plan for short clips, proxy resolution, and a compositing app that does the final assembly, and Procreate becomes a flexible rotoscoping and hand-drawn overlay tool within a professional pipeline.