How to Pull a Color from an Image in Procreate
StyleFrame Team6 min read
To pull a color from an image in Procreate, touch and hold on the image with a finger until the eyedropper ring appears, drag to the exact spot you want, and lift to set it as your active color. This works on an imported photo layer, on your own artwork, and on an image loaded into the Reference Companion. Once sampled, the color sits in your Color History, and you can save it to a palette or read its hex value for use in other apps.
The Fast Method: Touch and Hold
Procreate has no separate eyedropper tool. Sampling is a gesture, which is why many people miss it at first.
- Open your canvas with the image visible. The image can be a photo layer or any artwork.
- Touch and hold on the pixel you want to sample.
- A ring appears under your finger. The top half previews the color you're hovering over, and the bottom half shows your current active color.
- Drag to scrub across the image and watch the top half update.
- Lift your finger. The previewed color becomes your active color, shown in the Color Panel disc at the top right.
The two-tone ring is useful for judging a candidate color against what you're already using, for example when matching skin tones or a brand color.
Two Ways to Get an Image Into Procreate
The gesture is the same everywhere. What changes is where the image lives.
Insert the Image as a Layer
Tap the wrench (Actions), then choose Insert a photo. The image arrives as its own layer. Sample directly from it, then hide or delete the layer when you're done. This is the quickest route if you're painting over or near the image.
Use the Reference Companion
If you don't want the image on your canvas, load it into the Reference Companion. Touch and hold on the reference image to activate the color picker, just as you would on the canvas.
This keeps your layer stack clean. One quirk: the Reference Companion uses its own touch-and-hold timing. It works even if your normal eyedropper is mapped to a different gesture, but the hold duration can't be adjusted there, so it may take a bit longer.
Set Up the Eyedropper to Suit Your Hands
If the gesture misfires, check your settings. Tap the wrench, then Preferences, then Gesture Controls, and open the Eyedropper section. You can choose how the picker is triggered, such as touch and hold, a Quick Menu, or another gesture.
Some practical points:
- Touch and hold works for most people and needs no extra buttons.
- Quick Menu mapping is faster if you sample constantly. Note that a custom eyedropper mapping doesn't carry over to the Reference Companion, which still uses touch and hold.
- Delay settings let you shorten the hold time on the main canvas. If sampling feels sluggish, adjust it here.
Some older tutorials show the sidebar Modify button as a second sampling method. Depending on your version, that may or may not be configurable, so check Gesture Controls on your own device rather than assuming.
Sampling Accurately
Pulling a color is easy. Pulling the right color takes a bit more care.
Watch for noise. Photos contain grain, compression artifacts, and JPEG blocking. Sampling a single pixel can give you a value that isn't representative of the area. Sample several nearby points and compare the ring preview, or blur a duplicate of the image first and sample from that to get an averaged value.
Know what you're sampling. If your result looks off, check the layers above the image. Overlays, adjustment layers, and blend modes change what's visible, and what you see is what you're likely picking. Hide anything you don't want influencing the sample.
Use the Value tab for numbers. Open the Color Panel and switch to the Value tab. You'll see precision sliders along with numerical and hexadecimal values. This is where you verify what you sampled, and where you copy a hex value to paste elsewhere.
Check the color profile. If your canvas uses a different color profile from your After Effects project, the same hex code can look different between apps. Decide on your working space first, then compare.
Saving Colors You Pulled
Every sampled color lands in the Color History, which holds your last ten colors in the Disc, Classic, Harmony, and Value tabs. The oldest drops off as new ones come in, so don't treat History as storage.
To keep colors:
- Open the Palettes tab.
- Create a new palette or select an existing one.
- Add your current active color to the palette.
- Name the palette after the project or shot.
The Color Companion also surfaces your History at the top of your palettes, which is handy when you're sampling repeatedly during a painting session.
Troubleshooting
- Nothing happens when I hold. Confirm your Eyedropper gesture is enabled in Gesture Controls, and that you're holding still long enough for the ring to appear.
- The ring appears but the color is wrong. Check for hidden blend modes or layers above the target, and check that the image layer isn't set below an opacity-reduced layer.
- It works on the canvas but not in Reference. The Reference Companion picker uses a fixed touch-and-hold. Hold a bit longer and keep the finger steady.
- Colors look different in other software. This is often a color-profile or display-calibration issue, not a sampling error.
Moving Sampled Colors Into a Motion Pipeline
Procreate is often where motion designers and VFX artists build style frames, color scripts, and look-dev boards before moving to After Effects, Cinema 4D, Blender, or Nuke. A few habits make that handoff cleaner.
Carry hex values, not eyeballed matches. Copy the hex from the Value tab, then paste it into the After Effects color picker, a Cinema 4D material, or a Blender color field. Keep a text note of the values per palette so the whole team can refer to them.
Export a reference frame. Flatten your palette study to PNG and drop it into your comp.
Align color management early. Confirm what profile Procreate exported and what your After Effects project working space expects. A mismatch discovered after delivery is expensive to correct.
Quick Reference
Final Notes
The core answer is a single gesture: hold your finger on the image, scrub to the right spot, and release. The rest is about doing it reliably. Pick the right place for your reference, tune the gesture to your hands, sample more than one point on noisy photos, save what matters to a palette, and carry hex values and a consistent color profile into your next tool. That way, a color you pulled in Procreate still looks like the same color when it reaches your composite.