How to Perfect the Square in Procreate
StyleFrame Team7 min read
In Procreate, draw a rough square, keep your Apple Pencil on the canvas at the end of the stroke until QuickShape snaps it, then put a second finger down while the pencil is still held. The shape snaps a second time into a true square with equal sides and right angles. Lift the pencil to commit, then tap Edit Shape if you need to adjust individual corners. If you only get a rectangle or polyline, your freehand attempt was too far from square, so draw closer to the proportions you want or use a Drawing Guide grid.
Method 1: QuickShape with the second-finger snap
This is the fastest route.
- Pick any brush and draw a closed four-sided shape. It doesn't need to be neat, but it should be roughly equal in width and height.
- When you close the shape, don't lift the pencil. Hold it still for a moment until the stroke snaps into a clean quadrilateral.
- Keep the pencil down and place a finger from your other hand anywhere on the canvas. The quadrilateral snaps again into a perfect square.
- Lift the pencil and finger when you're happy with it.
The same gesture works across shapes: a rectangle becomes a square, an ellipse becomes a circle, and an uneven triangle becomes an equilateral one. It is a two-stage process, and the second snap only happens while your pencil is still on the screen. If you lift too early, you're left with the first-stage shape, which can be slightly off.
Rotate and scale before you commit
While the pencil is still down and the shape is snapped, drag to scale and rotate it. If you hold a second finger on the canvas while dragging, rotation locks into 15-degree increments. That makes 45-degree diamonds and exact quarter turns easy to hit. Lift the finger and rotation becomes free again; put it back down and the shape re-locks.
Decide on your size and angle before you lift.
Method 2: Tidy up with Edit Shape
After you release a QuickShape, an Edit Shape button appears in the bar at the top of the canvas. Tap it to enter Edit Shape mode, where the available options depend on the shape you drew. For a quadrilateral, you'll see options that let you convert it into a square or rectangle, plus transform nodes on the corners.
This route helps in two situations:
- Your second-finger snap didn't land. Tap Edit Shape and choose the square option rather than redrawing.
- You need to nudge the shape. Drag a node to adjust that corner, or drag the body of the shape between nodes to scale it uniformly.
Tap anywhere on the canvas to commit and leave Edit Shape mode. If you ignore the button, it disappears once you keep painting.
Be careful with node dragging if you need a true square. Pulling a single corner will break the equal-sides relationship, and you'll need to convert it back or use uniform scaling from the body of the shape.
Method 3: Exact sizes with the Drawing Guide
QuickShape gives you a perfect proportion, but not a specific dimension. For a square of an exact size, such as a 1080 × 1080 social frame or a 350 px tile, use a grid.
- Open the Actions menu (wrench), then Canvas, and toggle on Drawing Guide.
- Tap Edit Drawing Guide and set the grid size in pixels. If you want a square that spans four cells, set the grid so each cell is a quarter of the width you need.
- Reduce the guide's opacity so it doesn't dominate the canvas.
- Draw your square along the grid lines, then use QuickShape to snap it.
Because you're drawing against the grid, your freehand square starts out very close to the target, and the snap lands where you intended. This also helps with the failure described below.
Method 4: Build a square from a line
If QuickShape misbehaves on your device or Procreate version, you can build a square from straight lines:
- Draw a line and hold at the end until it snaps straight. Add a second finger to lock it to 15-degree angles.
- Duplicate the layer and rotate the copy 90 degrees.
- Repeat to create all four sides, then position them so the corners meet. Merge the layers when done.
A related approach is to snap half a square, then duplicate, flip horizontally, and merge. That's useful when your first snap leaves a small gap at one corner, since the mirrored copy closes the shape.
These methods take longer, but they're predictable and work as a fallback.
Troubleshooting: why you only get a rectangle or polyline
Some users report that QuickShape offers a polyline, an ellipse, or a generic quadrilateral but never a square. Usually one of these is the cause:
- Your freehand shape is too far from square. QuickShape appears to apply a tolerance. If the proportions are too far off, it won't offer a square as an option. Draw slower, and aim for equal sides. Using a circle or a grid as a visual guide helps.
- You're lifting before the second snap. The second-finger gesture only works while the pencil remains pressed on the canvas.
- The gesture trigger is configured differently. Go to Actions → Prefs → Gesture Controls → QuickShape to check how QuickShape is invoked and adjust the touch and pencil settings to suit your workflow.
- A recent update may have changed the behavior. Some users report the problem started after an update, and Procreate's team has acknowledged that the threshold is a little different than before and logged it for investigation. If a method that used to work now fails, try Edit Shape or the grid method instead of assuming you've done something wrong.
If you draw many squares in a row, the extra finger-down step becomes tedious. Some users have asked for a way to make perfect shapes the default, so the practical workaround is to draw one good square and duplicate it.
Know the limits of QuickShape
QuickShape is a snapping gesture rather than a dedicated shape tool like those in some desktop drawing software. That has a consequence:
- No stroke on the shape. Procreate staff have said applying a stroke to an object isn't currently possible, though they haven't ruled it out for the future.
Where perfect Procreate squares fit in a motion pipeline
If you work in After Effects, Premiere Pro, Cinema 4D, Blender, or Nuke, you probably don't need Procreate to make a mathematically perfect square. You may prefer to build the square natively in your compositing app if you plan to animate it.
Procreate squares are still useful for:
- Storyboard and animatic panels, where consistent frames keep boards readable.
- Hand-drawn textures and mattes, where the square is a base for a wobbly, inked, or painted treatment.
- Layout guides for title safe areas, grids, and composition studies before you build in your compositing app.
When you export, use PNG for transparency and set a canvas size that covers your final delivery resolution so you aren't upscaling later.
Quick reference
Perfect squares in Procreate come down to timing and a tolerable starting shape. Hold, add the second finger, set your rotation and size before lifting, and fall back on Edit Shape or a grid when the gesture doesn't cooperate.