How to Paint Inside the Lines Procreate
StyleFrame Team7 min read
To paint inside the lines in Procreate, put your line art on its own layer and constrain the paint with one of three tools. Set the line layer as a Reference layer and use ColorDrop on a layer beneath it. Alpha Lock a filled layer so strokes only land on existing pixels. Or select the area with the Automatic selection tool and paint within that selection. Each method keeps your linework untouched, and which one fits depends on whether you need flat fills, textured shading, or clean edges for animation.
Start with the right layer structure
Every reliable method below depends on the same setup: line art on its own layer, color on separate layers. If you paint on the same layer as your lines, you can't recolor, fix, or isolate anything without damaging the drawing.
A workable stack from top to bottom:
- Line art (locked or set as Reference)
- Shading and highlights (clipped or Alpha Locked)
- Base colors (one layer per shape or object)
- Background
Placing color layers below the lines is usually cleaner than painting above them in Multiply, because the line layer remains fully opaque and unaffected. If you do paint above the lines, set the color layer to Multiply so the lines show through.
One prerequisite for the fill-based methods: closed shapes. If your outline has even a small gap, the fill will leak into neighboring areas. Zoom in and check corners and junctions before you fill.
Method 1: Reference layer + ColorDrop
This is a fast route for flat color.
- Open the Layers panel, tap your line art layer, and choose Reference.
- Create a new layer below the line art for your color.
- Pick a color, then drag from the color circle in the top-right corner into the enclosed area.
Because the line layer is a Reference, Procreate reads its edges to decide where the fill stops, but the color is written to the layer you're on. Your linework stays pristine, and you can change the fill color or delete it without redrawing anything.
The same trick works on any layer pair. Draw a dividing line on one layer, mark it as Reference, and you can fill each side of it independently on separate layers.
Common issue: Thin, light gray halos along the edges. These are anti-aliased pixels the fill didn't reach. Use the selection method below, which paints under the line entirely.
Method 2: Alpha Lock for shading inside a fill
ColorDrop gives you flat shapes. To add gradients, texture, or multiple shades without spilling, lock the transparency of the filled layer.
- After filling a shape on its own layer, swipe right on that layer with two fingers. A checkerboard pattern appears on the thumbnail.
- Paint with any brush, at any opacity. Strokes only affect pixels that already contain color on that layer.
You can paint a messy, fast brush stroke across the whole canvas and the shape will remain intact. This is ideal for painted skin tones, hair highlights, or color variation inside a single object.
Alpha Lock has one limitation: it only knows about pixels on the current layer. If you need the paint to respect a boundary that exists on a different layer, use Reference (above) or a selection (below).
Clipping masks as an alternative
A Clipping Mask does something similar without modifying the base layer. Create a new layer above your filled shape, tap it, and choose Clipping Mask. Anything you paint on the new layer only shows where the layer beneath it has pixels. This is better when you want to keep the base fill clean and treat shading as a separate, adjustable layer. You can tweak opacity, change blend modes, or turn it off without touching the base.
For animation or compositing, clipped shading layers are generally more flexible than Alpha Lock, because you can toggle them or export them separately.
Method 3: Selection tool for hard boundaries
When you need the paint to stop at a specific edge, regardless of layers, make a selection first.
Select the inside directly
- Tap the Select tool (the squiggly S-shaped icon).
- Choose Automatic mode and make sure Color Fill is off in the bottom toolbar. If it's on, tapping will fill the area with color instead of selecting it.
- Tap inside the shape. The unselected area shows diagonal hatching.
- Switch to the brush, move to a layer below the line art, and paint.
The paint will stay inside the selected region.
Select the outside, then invert (the better trick)
Selecting the inside directly stops at the edge of the line, and anti-aliased edge pixels can end up unpainted. A more robust approach:
- With Automatic selection, tap the area outside your shape.
- Tap Invert. Now the shape and its outline are selected.
- Paint on a layer below the line art.
The color extends underneath the lines, which removes the light fringe that sometimes appears around inked edges. It also lets you change the line layer's blend mode later without a hole in the color behind it. This is a classic pro coloring trick.
When you're finished, tap the Select tool again to exit selection mode.
Choosing between the methods
For loose sketches without closed shapes, you won't get a clean fill from ColorDrop. Either close the gaps with a small brush stroke on a helper layer, or paint on a Multiply layer above the lines and accept a looser result.
Troubleshooting leaks and fringes
- Fill floods the whole canvas: There's a gap in the outline. Zoom in, close it, or fill on a duplicate of the line art where you've sealed the gaps, and keep that duplicate as your Reference.
- Selection doesn't show hatching: Automatic selection often doesn't show the diagonal lines the way you expect until you switch to a brush. Check that Color Fill is off and the Add mode is on.
- Select-the-layer does nothing useful: Choosing the layer selects its painted pixels, not the empty area inside them. Use Automatic selection on the empty region instead.
- Color covers the lines: Either the color layer is above the lines in Normal mode, or you need to move it below. Multiply is the quick fix.
- Pale halos around edges: Use the invert method so color sits beneath the line.
Preparing painted art for motion work
If your Procreate artwork is headed for After Effects, Premiere Pro, or a Nuke comp, the layer discipline above pays off twice. Keeping color, shading, and line work on separate layers lets you animate pieces independently, adjust color in post, or composite the lines over a different background.
A few habits that help:
- Name your layers before exporting. Procreate's default names make rigging in After Effects painful.
- Keep lines on their own layer with transparency, so you can multiply, screen, or recolor them in the comp.
- Paint slightly past the lines (the invert trick) so edges don't show gaps when layers are scaled or moved.
- Work at the final delivery resolution where possible, since upscaling raster painting later softens the edges you worked to keep clean.
Quick recap
- Keep line art on its own layer, and keep color on separate layers.
- Use Reference + ColorDrop for fast flat fills on closed shapes.
- Use Alpha Lock or a Clipping Mask to shade inside a shape without spilling.
- Use Automatic selection (ideally select outside, then Invert) when you need hard boundaries and paint under the lines.
- Name and organize layers so the artwork transfers cleanly into After Effects, Nuke, or any other tool downstream.