How to Paint Hair Procreate
StyleFrame Team7 min read
Paint hair in Procreate by building it in layers: fill the shape with a dark base, add mid-tone strand clusters that follow the direction of hair flow, then add thin light strands for highlights. Blend the start and end of each stroke with a soft brush, and finish with flyaways around the edges. Keep each stage on its own layer, using clipping masks or Alpha Lock, so you can adjust color and value without repainting.
Understand Hair Before You Paint It
Most "bad" painted hair comes from skipping structure, not from weak brushwork. Hair behaves as a few large masses that break into smaller clumps, which break into strands. Painting individual strands first produces a wiry, flat result.
Check three things before you start:
- Origin point. Hair grows from a part or crown, and everything flows away from it. Mark this point lightly and let every stroke respect it.
- Large forms. Treat the hair as a few overlapping volumes, not a texture. Decide where the planes turn, where the hair catches light, and where it falls into shadow.
- Hair type. Straight hair tends to be glossy and lies close to the scalp. Wavy hair follows an S-shaped rhythm. Curly and coily hair is best read as an overall silhouette, with curls following that shape instead of being drawn one by one.
A reference photo or a painted portrait you admire is worth more than any brush pack. Study where the darkest values sit (near the roots and under overlapping clumps) and where the highlight band falls.
Set Up Your Canvas and Brushes
Start with a clean silhouette of the hair shape, either as a sketch on a Multiply layer or as a flat-filled shape. Keep the sketch above your paint layers so it never gets covered, and lower its opacity once you're confident in the form.
You don't need a custom brush pack. Procreate's defaults cover the job:
- A pencil or pen-style brush (such as the 6B pencil or Technical Pen) for the initial flow lines and the outline.
- A round or textured brush with pressure sensitivity for strand clusters. Tapered strokes that thin out at the ends are what make hair read as hair.
- A soft airbrush for blending and gentle color shifts.
- A smudge or blending brush for softening transitions.
If you use a dedicated hair brush, the principle is the same: tapered ends, varied pressure, and strokes that follow the flow.
Pick a small palette first, roughly four or five values of one hue, from near-black to a light highlight tone. Limiting your palette keeps the hair cohesive and stops you from over-rendering.
Step-by-Step: Painting Hair in Procreate
1. Lay down the dark base
On a new layer beneath your sketch, fill the whole hair shape with your darkest color and clean up the edges. Starting dark means you won't have to add heavy shadows later. It also gives you a believable depth underneath everything else. If you plan to recolor the hair later, keep this layer separate.
2. Block in the mid-tones as strand clusters
Add a new layer and choose a slightly lighter shade. Using a tapered brush, paint thick clumps that follow the hair's flow. Think of each stroke as a ribbon of hair, not a single strand. Let strokes start near the part or root, curve with the form, and taper at the tips.
If the tone comes out too dark or too saturated, turn on Alpha Lock for that layer and go over it with a soft airbrush in a different color. This changes the color without touching your stroke shapes.
3. Add form shadows
Create a layer above the base, set it to Multiply, and clip it to the layer below. Paint shadows using the base color, thinking about where your light source is. Shade the hair that turns away from the light, the areas under overlapping clumps, and the zone near the scalp. Using a clipping mask means the shadows can't spill outside the hair shape.
4. Paint highlights
Add another layer and pick a lighter version of your base hue. Place highlights where the light hits the strongest planes, usually along the top curve of the head or on the crest of a wave or curl. Highlights on hair often form a band that follows the shape of the head, so don't scatter them evenly across the surface.
Then switch to a thinner brush and paint finer, lighter strands over the clumps. These should be thinner and lighter than your mid-tone strokes. Vary pressure, spacing, and length so the strokes don't look mechanical.
5. Blend with intent
Now soften transitions. Use a soft blending brush or a low-opacity airbrush on the start and end points of your clumps so they melt into each other. Don't blend everything: leave some sharp strand edges so the hair keeps its texture. Blending too much produces a smooth, plastic look.
6. Add flyaways and edge detail
Put a new layer at the bottom of the hair stack (or just above the background) and paint short, fine strands around the hairline and silhouette. Add a few stray hairs crossing over the edge. These small imperfections do more for realism than extra highlight work. Keep them sparse, since too many look like frizz.
7. Adjust color and value last
When the painting is finished, use Adjustments (such as Saturation) on individual layers. Push the highlights slightly warmer or cooler than the shadows, and check the overall value structure in grayscale. Hair that reads well in black and white will read well in color.
Common Mistakes and Fixes
- Painting every strand. Work from big shapes to small. Detail belongs only where the eye lands.
- Even highlights. Place them in bands that follow the form.
- Hard, pointed ends on every lock. Vary the ends: some tapered, some clumped, some overlapping.
- Ignoring flow. If a stroke fights the direction of growth, it will look wrong even when the color is perfect.
- Flat lighting. Without planes and shadows beneath the strands, the hair looks like a texture pasted on a shape.
- Over-blending. Keep some crisp strand edges.
Taking Painted Hair Into a Motion Pipeline
A painted hair study is often a starting point in motion work, not the final deliverable. You might need a character's hairstyle as a keyframe, a style reference for a title sequence, or a painted plate to composite into a shot.
Organize your hair into named layers (base, shadows, highlights, flyaways) before handing it off. That lets a compositor in After Effects or Nuke adjust each pass independently or separate the flyaways for secondary animation.
If you want to push painted frames into moving footage, is one AI video and motion tool you could explore alongside your painting tools. Check its site for current features.
AI-generated motion still needs review. Check hair edges, strand continuity, and temporal consistency frame by frame, and paint fixes where needed, as you would with any plate.
A Quick Practice Routine
- Pick one reference and paint only the silhouette and three values.
- Repeat the same hair in a different hair type to learn how flow changes.
- Add strands only after the large forms read clearly in grayscale.
- Save each version as a layered file so you can compare how structure, color, and detail affect the result.
FAQ
What's the best brush for painting hair in Procreate? A pressure-sensitive brush that tapers at the ends works best. Procreate's default pencils, pens, and round brushes are enough, and a soft airbrush handles blending.
Should I paint hair strand by strand? No. Block in clumps and large forms first, then add fine strands only at the highlights and edges.
How do I change hair color without repainting? Keep the hair on separate layers, then use Alpha Lock with a soft brush or the Adjustments menu to shift the color.
How do I make hair look glossy versus matte? Glossy hair has tighter, brighter highlight bands with stronger contrast. Matte hair has softer, broader highlights and less contrast between tones.
Can I use painted hair in an After Effects project? Yes. Keep your passes separated on named layers and bring them into your composite to animate or use as references.