How to Paint Fur Procreate
StyleFrame Team7 min read
To paint fur in Procreate, block in a dark base that follows the animal's form, then build up lighter layers of overlapping hair clumps in the direction the fur grows. Smudge the first layers into one mass, add clumps with fur-style brushes (the built-in Short Hair brush from Touch-Ups works well for blending), and leave gaps so the darker layers show through. Finish with a small number of fine strokes at reduced opacity. Work dark to light, big to small, and keep each pass on its own layer.
Start with the structure, not the hairs
Fur reads as fur because of the shape underneath it. Before you touch a hair brush, decide on three things:
- Form: Is this a round tail, a flat flank, a ruff around a neck? Fur wraps over these volumes and its strokes should curve with them.
- Direction of growth: Hair flows along the body, parts at the face, and swirls around joints and ears. Sketch a few flow lines on a separate layer if you need a guide.
- Light logic: Decide where the key light lands so your highlights and core shadows have a plan before the texture goes in.
Pull up a reference photo of the actual animal or a close match. Fur varies enormously: a leopard's short, dense coat, a llama's fluffy fiber, and a wet dog's separated clumps all need different stroke lengths and gap spacing.
Step 1: Block in a dark base
Create a canvas at a size that suits your final use (more on that below). On a new layer, fill your shape with the darkest color you expect in the fur. Many animals have a darker undercoat, so starting dark is both practical and believable.
Use any brush you like for this stage. A Wet Acrylic from the Painting set, a monoline, or an airbrush all work, because nothing here will be visible as texture later. Lean toward warm hues for a warm piece and cooler hues for a cool one. The base color sets the mood for everything layered over it.
Step 2: Lay in the big value shapes
On the same layer or a new one above it, add slightly lighter colors where the light will fall and some subtle color shifts for variation. Keep the brush large and stay relatively dark overall. You are mapping out where highlights and shadows will go, not painting fur yet.
If your subject has markings, such as leopard spots, stripes, or patches, place them now with a slightly smaller brush. They will look pasted on at this stage. That is expected and fixed in the next step.
Step 3: Smudge in the direction of growth
Switch to the Smudge tool and choose a short hair-style brush (the Short Hair brush in the Touch-Ups set is a common choice). Drag along the direction the fur grows. This does two things:
- It merges your layered colors into one believable mass.
- It blends markings into the coat so they sit in the fur rather than on top of it.
When blending markings, smudge in both directions: let the marking's color push into the base, and let base color push back over the marking. Keep it light. Over-smudging produces a soft, airbrushed look that reads as plastic, and many tutorials stop at exactly this point. Treat smudging as the foundation and not the finish.
Step 4: Build clumps, not individual hairs
This is where realism comes from. On a new layer, pick a fine hair or flowing hair brush from the built-in sets (or a custom fur brush, see below) and follow three rules:
- Paint clumps. Real fur groups into locks. A single stroke with a multi-bristle brush can lay down several strands at once, which is faster and looks more natural than drawing every hair.
- Leave gaps. Do not fully cover the layer underneath. Gaps let the darker undercoat show through, which creates depth.
- Vary length and curve. If every stroke is the same length and arc, the result looks combed. Mix longer sweeping strokes with short flicks, and let curvature change near joints, folds, and edges.
Start with a dark color close to your base, then work lighter. Each pass should use a lighter value and a smaller brush than the last. Put each pass on its own layer so you can adjust opacity, erase, or recolor later without damaging earlier work.
Step 5: Soften and unify
Fresh hair strokes can look too sharp against the smudged base. Fix that with a few options:
- Use a flowing hair brush in a mid-value color to add broader clumps over the sharper lines.
- Reduce layer opacity so the strokes sit back into the coat.
- Use an eraser with a soft airbrush to fade the starting points of strokes, so hairs appear to grow out of the coat rather than float on top of it.
- Lightly smudge selected areas, leaving others crisp. Fur has varied texture, with smooth patches and rough patches, and uniform softness looks artificial.
Step 6: Add highlights and detail last
On a final layer, add your lightest strokes where the light source hits: the top of the head, the back, the edges of ears, and rim areas. Use a small brush such as a technical pen at lowered size and opacity for fine flyaway hairs. Restraint matters here. A handful of well-placed fine strokes sells the effect, while hundreds of them flatten it.
Check your edges too. A silhouette with a perfectly smooth outline looks cut out. Break it up with small tufts and uneven strokes, especially at the tail, ears, and underside.
Using custom fur brushes
The default brushes are enough to paint convincing fur, and learning to do it with them first gives you a better feel for what a specialty brush is doing. When you want speed or a specific texture, free and paid fur brush sets exist in the Procreate community and from brush designers. Look for sets that include a base blocking brush, a clumping brush, and a fine detail brush. Whatever you install, test it on a scratch canvas first. Brushes with heavy built-in texture can look repetitive if you rely on them for every layer.
Painting fur for motion work
If you are a motion designer or animator, you are probably not painting a single illustration. You are building an asset that has to move. A few habits make Procreate fur much easier to use in After Effects, Nuke, or Blender:
- Separate by function. Keep the base, mid-tone clumps, highlights, and flyaway hairs on separate layers. Grouping them by body part (tail, head, ears) lets you animate them independently.
- Paint beyond the edges. If a tail will sway or an ear will flick, paint the hidden areas behind overlaps so nothing reveals an empty gap when parts move.
- Work large. Create the canvas at a high resolution, because fine strokes degrade quickly when scaled up in comp.
- Export for compositing. Export your layers in a format your compositing software accepts, keeping each element on its own layer.
- Keep a clean alpha. Paint on transparent layers rather than over a colored background, so you can drop the fur into a scene without a messy matte.
In comp, subtle displacement, a light wiggle on hair layers, or parallax between layers can give a painted fur asset convincing secondary motion without redrawing anything.
Common mistakes to avoid
- Starting light. Painting highlights first leaves no room to build depth. Work dark to light.
- Ignoring the form. Strokes that cut across the body instead of following it flatten the volume.
- Uniform strokes. Same length, same curve, same spacing: the "comb" effect.
- Over-smudging. Blending is a base step, not the whole technique.
- Too many fine hairs. Detail should be sparse and purposeful.
- Flattening too early. Merging layers before the piece is approved removes your options, especially when the asset has to go into animation.
A quick checklist
- Gather references for the specific animal.
- Block in a dark base following the form.
- Add value shapes and markings.
- Smudge along the direction of growth.
- Layer clumps from dark to light, large to small, with gaps.
- Soften starts and edges, vary the texture.
- Add sparse highlights and flyaways.
- Export layers organized for your compositing or animation pipeline.
Fur is built from patient layering and observation more than from any one special brush. Once you have the process down, the same approach scales from a single illustration to a full set of animated, composited assets.