How to Move Something to a New Layer in Procreate
StyleFrame Team7 min read
To move something to a new layer in Procreate, select it with the Selection tool, swipe down with three fingers to open the Copy & Paste menu, and tap Cut & Paste. Procreate lifts the selected pixels off the original layer and places them on a new layer directly above it, in the same position. If you want to leave the original untouched, tap Copy & Paste instead.
Step-by-step: move a selection to a new layer
- Open the Layers panel and tap the layer that holds the element you want to separate. Procreate highlights it as your Primary layer, and that is the layer the selection reads from.
- Tap the Selection tool (the S-shaped icon in the top toolbar). Choose a mode at the bottom of the screen: Automatic, Freehand, Rectangle, or Ellipse.
- Select the element. In Freehand, draw around it and close the loop. In Automatic, tap or drag over the area and pull the threshold bar until the selection fits.
- Swipe down with three fingers anywhere on the canvas. The Copy & Paste menu appears.
- Tap Cut & Paste. The selected pixels move to a brand-new layer above the original and stay in place. The original layer now has a gap where the content used to be.
- Rename or reorder the new layer as needed (covered below).
That is the whole workflow. Everything else is about making the selection clean and handling the layer afterward.
Cut & Paste vs. Copy & Paste
The two commands look similar but do different things to your source layer.
- Cut & Paste moves the pixels. The source layer is left with a hole, and the new layer holds the only copy. Use it when you're splitting a flattened sketch into separate elements, such as pulling a character off a background.
- Copy & Paste duplicates the pixels. The source layer stays intact, and the duplicate lands on a new layer above it. Use it when you want a safety copy or plan to rework one version, for example to build a shadow or highlight pass from the same shape.
If you're unsure, go with Copy & Paste. Deleting the extra pixels later is easier than repairing a hole in a painted layer. Undo is also available if the result isn't what you wanted.
Getting a clean selection
Most failed "move to a new layer" attempts come down to a poor selection, not the command itself.
- Use Automatic mode for flat, hard-edged shapes. It works well on line-and-fill illustration, where each color region is distinct.
- Use Freehand for painted or textured work. Draw loosely around the element, then refine with the Add and Remove buttons.
- Feather the edge when the content has soft transitions. A small feather avoids a hard cut-out edge when you cut a painted element out of a textured background.
- Check the active layer first. Cut and copy actions only apply to the Primary layer. If the element spans multiple layers, merge them first or repeat the process per layer.
- Invert when it's easier. Sometimes selecting the background and tapping Invert is faster than tracing a complicated subject.
Moving the object once it's on its own layer
With the element isolated, repositioning is simple.
- Make sure the new layer is the Primary layer.
- Tap the Transform tool (the arrow icon).
- Drag to move, or use the corner handles to scale and rotate.
Procreate also offers a nudge function for small adjustments. In the version covered by a 2023 tutorial (5.3.1), you tap on the canvas outside the bounding box in the direction you want the content to shift, and it moves in small increments. Dragging after tapping outside the box also repositions the object freely. Behavior can vary slightly between versions, so test it on a throwaway layer if you rely on precise nudging.
Moving layers within the stack
Moving content to a new layer is only half of the job. The new layer also needs to sit in the right place in the stack.
Reorder layers. Tap and hold a layer in the Layers panel, then drag it up or down. Layers at the top of the list sit in front, and layers at the bottom sit behind everything above them. If a color layer is covering your line art, drag the color layer beneath the line layer.
Move several layers at once. Swipe right on additional layers to add them as Secondary selections (dark blue). Then drag them together, or use the Group option that appears at the top of the panel. Note that you can't use Adjustments with multiple layers selected, and cut and copy only apply to the Primary layer.
Put layers into a group. With multiple layers selected, tap Group to collect them into a folder. Selection and Transform actions then apply to all the layers in that group at once, which is useful for moving an entire character rig or a background section as one unit.
Select a layer from the canvas. Under Actions > Prefs > Gesture Controls > Layer Select, you can assign a touch or Pencil gesture that reveals which layers sit under a given point on the canvas. This saves scrolling a long layer list when you're hunting for the right one.
Moving a whole layer's contents rather than part of it
If you want to move everything on a layer, you don't need a selection at all. Make it the Primary layer and use the Transform tool directly. The bounding box covers the layer's content. To transfer all of a layer's pixels onto a different layer, you can select all of the layer's pixels through the Layer Options menu and then cut and paste.
Common problems and fixes
- "The Cut & Paste option doesn't appear." You need an active selection. If nothing is selected, the three-finger swipe shows a different set of options.
- "My object has a jagged or halo edge." Add a little feathering, or use Automatic selection with a slightly tighter threshold, then clean the edge with a soft eraser on the new layer.
- "The pasted content moved." Cut & Paste normally keeps the original position. If it shifted, you may have accidentally dragged while the Transform tool was active. Undo and try again.
- "The new layer is in the wrong place." Pasted layers appear above the source layer. Drag them where you need them.
Why clean layers matter downstream
If your Procreate work feeds a motion pipeline, layer discipline pays off. Elements that are properly separated, named, and grouped become animatable pieces: a character's arm on its own layer, a prop on another, a background plate beneath. Elements baked into one flat layer have to be cut apart again later.
A few habits make this smoother:
- Name layers before exporting. "Arm_L" is far more useful than "Layer 47" once it's inside a compositing project.
- Keep overlapping parts separate. Anything that will move independently needs a clean layer with enough painted area behind occlusions to avoid gaps.
- Check blend modes after import. Complex modes and some adjustments may not translate identically, so verify the look in your comp.
- Group by function. Put line art, color, and shadow passes in separate groups so they stay manageable in a layer-heavy comp.
Quick reference
Once the select, cut-and-paste, and reorder steps become habit, separating a sketch into animation-ready pieces takes seconds, and your downstream comps stay far cleaner.