How to Move a Layer Behind Another in Procreate
StyleFrame Team6 min read
To move a layer behind another in Procreate, open the Layers panel, press and hold the layer you want to send back, and drag it below the layer it should sit behind. Procreate stacks layers like a list: the top of the list is the front, and the bottom is the back. Release the layer when it sits below the target layer. The same drag gesture works for groups and for multiple selected layers.
Quick Steps to Send a Layer Behind Another
- Tap the Layers icon in the top-right corner to open the panel.
- Find the layer you want to push back.
- Press and hold it until it lifts off the list.
- Drag it down past the layer that should end up in front.
- Let go. The artwork on the canvas updates immediately.
That's the whole mechanic. Most confusion comes from what's being moved and where it lands, so the sections below cover the cases you'll actually run into.
How Layer Order Works in Procreate
If you've used After Effects, Photoshop, or Nuke's merge ordering, the model is familiar. Each layer is a flat raster image, and Procreate composites them from the bottom of the list upward. Whatever is higher in the list covers whatever is lower, wherever the upper layer has opaque pixels.
Reordering is done by dragging layers in the list, so the order of the list is the main stacking control.
One detail helps:
- Layer opacity and blend modes change how a layer reads against what's beneath it, but not its position. A layer set to Multiply can look like it's "behind" line art even though it's above it.
Moving a Single Layer Behind Another
Open the Layers panel and identify two layers: the one you're moving (A) and the one it should sit behind (B). A must end up lower in the list than B.
Press and hold A. After a beat it lifts and follows your finger or Apple Pencil. Drag it down until it's beneath B, then release. Check which layer is active (highlighted bright blue) before you paint.
The classic example: color covering line art
A common situation is painting color on a new layer that lands above your line art. The color layer sits in front and hides the lines. The fix is the same drag: hold the color layer and move it below the line art layer. Linework reads on top, color stays behind, and you can keep painting without flattening anything.
Moving Multiple Layers at Once
You can reorder several layers in one move.
- Tap one layer to make it the Primary layer (it highlights bright blue).
- Swipe right on other layers to add them as Secondary layers (dark blue).
- Press and hold one of the selected layers and drag. The whole selection moves together.
Be aware that selecting multiple layers changes what other tools do. Selection and Transform actions apply to all selected layers, but you can't use Adjustments, and painting only affects the Primary layer. If a stroke is landing somewhere unexpected, check your selection.
Once multiple layers are selected, a Group option appears in the Layers panel. Grouping is often the cleanest way to reorder: combine a character's layers into one group, then move the group behind or in front of other groups with a single drag.
Working With Groups
Use the arrow on the right of a group to collapse it so the list stays manageable while you reorder.
Order inside a group is independent from the group's position in the main stack. A layer can be at the top of its group and still sit behind a layer outside the group, because the whole group is treated as a unit in the parent list. If a layer won't go behind something you expect, check whether one of them is nested.
Faster Ways to Find the Right Layer
Hunting through a long list is slow on complex illustrations. Two shortcuts help:
- Layer Select: Enable it under Actions > Prefs > Gesture Controls > Layer Select. Once configured, you can touch the artwork on the canvas and Procreate shows which layers sit under that point, so you can jump straight to the one you want to move.
- Naming and grouping: Give layers clear names and group by object. It's basic, but it matters when you hand files to another artist or an animator.
Troubleshooting
The layer jumps to the wrong spot. Drag slowly and check where the layer sits in the list before you release.
Nothing seems to change. The layer may be hidden, at low opacity, or covered by other layers you didn't realize were above it. Toggle visibility checkboxes to isolate.
Layers reversed after dragging between canvases. Dropping layers directly onto a canvas can invert their order. Open the Layers panel in the receiving canvas first and drop them there to preserve order. Also note that dragged layers arrive as PNG images, so blend modes and opacity settings don't carry over and need to be reapplied.
Wrong layer receives paint. Procreate paints on the Primary layer only. After any reorder, confirm which layer is highlighted bright blue.
Taking Procreate Layer Order Into an After Effects Pipeline
For motion designers and animators, Procreate is often where the stills originate: character designs, storyboards, texture passes, style frames. Layer order matters at handoff because it becomes the stacking order in your comp.
A few practical habits:
- Settle the order before export. Decide what's behind what in Procreate so you aren't guessing in After Effects. Name layers meaningfully, since clear names make the handoff easier.
- Separate elements for parallax. If you plan to animate depth, split foreground, midground, and background onto distinct layers or groups and keep their order consistent.
- Check what survives export. Layers dragged out individually come out as PNGs, so effects like blend modes won't travel with them. Test a small file first so you know what arrives intact in After Effects before you commit to a full scene.
- Keep transparency clean. Layers that overlap by design should have clean edges so you can move them apart in a comp without fringes.
Quick Recap
- Hold a layer in the Layers panel and drag it below the layer it should sit behind.
- Top of the list is front, bottom is back.
- Swipe right to select multiple layers, then drag them together or group them first.
- Check nesting inside groups when ordering doesn't behave as expected.
- Confirm your active layer after every reorder.
- Settle layer order and naming before exporting to After Effects.
Once the stack is right, the rest of the pipeline gets easier, whether you're parallaxing layers in a comp or taking those stills further.