How to Merge 2 Layers in Procreate
StyleFrame Team7 min read
To merge two layers in Procreate, open the Layers panel, tap the top layer, and choose Merge Down. The layer must sit directly above the one you're merging into. You can also pinch the two layers together with two fingers. The merged layer takes on the blend mode of the bottom layer, and the only way to reverse the merge is to undo it right away.
Method 1: Merge Down
This is the most predictable way to combine two layers.
- Open the Layers panel (the two stacked squares in the top right).
- Make sure the two layers are adjacent. If they aren't, press and hold one until it lifts, then drag it next to the other.
- Tap the top layer's thumbnail to open its menu.
- Tap Merge Down.
The two layers become one. The result takes on the blend mode of the lower layer. That detail causes most of the surprises people run into, covered below.
Method 2: Pinch to merge
The pinch gesture does the same thing faster, and it works on any number of layers.
- Place one finger on the top layer and another on the bottom layer of the range you want to combine.
- Pinch your fingers together until the layers collapse.
- Release.
Every layer between your two fingers merges into one. Hidden layers in that range are not included in the merged result, but if you undo, they come back. This is handy when you want to leave a reference or a rough sketch out of the merge, but check your layer visibility first so nothing ends up merged or left out by accident.
Method 3: Group, then flatten
If you're combining a whole set of layers, such as every element of a character, a group is cleaner.
- In the Layers panel, swipe right on each layer you want to select. Selected layers turn blue.
- Tap Group.
- Tap the group's name and choose Flatten.
The group becomes a single layer. This works well when the layers you want aren't a convenient adjacent pair, because you can organize them into a group first.
What changes when you merge
Merging is destructive in a way that matters for production work. Keep these behaviors in mind.
Blend modes get baked or altered
When two layers merge, the result inherits the lower layer's blend mode. A Multiply layer merged into a Normal layer gets flattened into Normal pixels, so the result may look different than the stack did before. A single layer can't be both Overlay and Multiply, so combinations of different blend modes rarely survive a merge intact.
Blend modes also interact with everything beneath them, not just the layer they're merged with. If a layer set to Multiply or Overlay is merged without the content below it, it loses the pixels it was blending against.
A reliable fix is to give the stack a solid base. Place a solid-colored shape under the layers you're merging, set to Normal, then merge the whole stack onto it. Because the result is built on an opaque Normal layer, it looks the same as the original stack.
The default background color layer is not part of a merge. If your artwork depends on that white background to look right, hide it and preview the canvas. If the art looks different with the background off, it will look that way after merging too.
Merging can't be separated later
Procreate has no easy way to unmerge. If you notice the mistake immediately, undo. Once you've done more work, or closed the project, the layers are gone. You can cut and paste a selection onto a new layer, but if elements overlap, the pixels are fused and separating them cleanly may be impossible.
For that reason, only merge layers once you're confident you won't need to adjust them independently. If layers don't overlap, merging them is low-risk. If they overlap, be more careful.
How to merge and keep the originals
Often you want a combined version without losing the separate layers. There are three practical approaches.
Duplicate before merging
Duplicate each layer, then merge the duplicates. The originals stay untouched. This is the simplest option and works for small jobs.
Duplicate the whole artwork
In the Gallery, duplicate the entire canvas and do your merging on the copy. Your multi-layer master stays intact, and you can bring the merged result back into the original later if needed. This is the safest route for a big flatten.
Merge, copy, undo, paste
This one is clever but riskier:
- Pinch the layers to merge them.
- Swipe on the merged layer and tap Copy.
- Undo to restore the separate layers.
- Tap the Actions (wrench) icon, then Insert Image from Clipboard.
You end up with a new merged layer on top of your untouched originals. The risk is that if Procreate is interrupted between the merge and the undo, such as by a crash or a call, you may lose the chance to undo. Duplicate your layers first if the project matters.
A fallback: merge in Photoshop
If you need finer control over how blend modes combine, you can export the file as a PSD and merge the layers in Photoshop. Some artists use this when Procreate's merge changes the look in ways they can't work around. Be aware that Photoshop and Procreate don't always handle blend modes identically, so check the result against your original canvas.
Troubleshooting common issues
Merge Down is missing or does nothing. The layer you tapped is probably the bottom layer, or it's inside a group where there is nothing below it. Check the layer order and make sure the target layer is adjacent.
The colors shifted after the merge. Blend modes are the likely cause. Set the bottom layer to Normal, add a solid base beneath the stack, and merge again from an undone state.
A layer disappeared from the merge. Hidden layers aren't included when you pinch-merge. Make them visible first if you want them included.
I can't add more layers. Procreate limits the number of layers by canvas size and resolution, so merging non-overlapping layers is a standard way to free up room. Merge layers that don't touch each other so you can still edit the pieces later.
The merged layer is locked or behaving oddly. Check whether Alpha Lock is enabled on the layer. With Alpha Lock on, you can only paint on areas with existing content, which can look like a bug when you're trying to add something new.
Merging layers for a motion pipeline
Many motion designers and VFX artists don't deliver from Procreate. They use it to paint textures, concept frames, matte paintings, or hand-drawn elements, then bring them into After Effects, Nuke, or Blender. That changes how you should think about merging.
- Keep separation for anything that will move. If a character's arm needs to rotate in After Effects, merging it into the torso layer makes your life harder. Merge only layers that will always move together.
- Merge what's static. Background details, texture passes, and shading that won't be animated are good candidates for flattening, since this reduces layer count in your comp.
- Export a flattened reference separately. Duplicate the artwork, flatten the copy, and export that as a look reference alongside your layered PSD.
- Name layers before exporting. Procreate names layers sequentially by default, and renaming them takes seconds. Clear names save time once the file lands in a compositing package.
Where Styleframe fits after the merge
Once your Procreate layers are in order, the next step is often turning still artwork into motion. is one tool for that step.
This is also a reason to be careful with merging. A clean, deliberately flattened frame makes a better reference or keyframe than one with stray blend-mode artifacts, so take a moment to confirm that your merged result looks the way you intend before you send it downstream.
Quick reference
Merging in Procreate takes a couple of seconds. Doing it without regrets depends on checking adjacency, blend modes, and visibility first, and keeping a duplicate of anything you might need to edit later.