How to Make Wavy Font in Procreate
StyleFrame Team6 min read
You can make a wavy font in Procreate by rasterizing a text layer and bending it with either the Liquify tool (Push mode) or the Warp tool's mesh. Liquify is faster and looser, while Warp gives you a more even, repeatable wave. Duplicate the text layer first, because once you distort it you can no longer edit the wording.
What Procreate Can and Can't Do With Text
Procreate lets you add a text layer, pick a font, and size it. Any wavy result comes from distorting pixels after the type is set.
That has two consequences:
- Distortion is destructive. Liquify and Warp both rasterize the text. Keep an untouched, editable duplicate hidden in your layer stack.
- Resolution matters. Bending pixels softens edges, so start with a large canvas and large type. If the lettering is headed for video, work at or above your final frame size.
Set up the text first. Tap the Actions (wrench) icon, choose Add, then Add Text. Type your word, choose a font, and size it. Chunky, rounded, or heavy display fonts take a wave better than thin hairline faces, which can break apart when pushed.
Method 1: Liquify Push for a Hand-Made Wave
Liquify is the quickest route and gives the most organic, hand-lettered result.
- Duplicate your text layer and hide the original.
- With the duplicate selected, tap Adjustments (the magic wand) and choose Liquify.
- Select Push at the bottom of the screen.
- Set the brush Size to roughly the height of one letter or a bit larger. Too small and you tear individual letters. Too large and you drag the whole word.
- Drag in short, alternating vertical strokes: push the first letters up, the next down, then up again. Think of it as nudging pixels along a sine curve rather than drawing the curve.
If you want the wave to read evenly, work in a rhythm. Count your strokes, keep each one roughly the same length, and place them about one letter-width apart.
Best for: quick lettering, posters, social graphics, and any look where a slightly imperfect wave is a feature.
Watch out for: inconsistent amplitude. Liquify has no guide, so the wave can drift. Undo and redo strokes rather than stacking corrections.
Method 2: Warp Mesh for a Controlled, Even Wave
Warp is slower to set up but gives you precise control over where each part of the word moves.
- Duplicate the text layer.
- Tap the Transform tool (the arrow icon) and choose Warp in the bottom toolbar.
- Tap Advanced Mesh to get a grid of control points.
- Drag control points up and down in an alternating pattern across the width of the word. Points in the same column should move together to keep letters upright. Points in the same row move apart to create the curve.
- Tap Transform again when you are finished.
A few habits help here:
- Draw a guide first. Sketch a sine-style wave on a separate layer so you can match your mesh points to it. Delete or hide it before export.
- Keep columns consistent. If you pull only the top row of points, letters stretch instead of riding the wave. Move top and bottom points by similar amounts.
- Use fewer, larger moves. Heavy distortion on a small mesh creates pinching. If the wave needs to be dramatic, apply it in two passes rather than one.
Best for: logos, titles, and lettering where the left and right sides need to feel balanced.
Watch out for: stretching at the extremes. Keep the amplitude modest for legibility, particularly with condensed fonts.
Method 3: Letter-by-Letter Offsets
For the most deliberate control, split the word into individual letters and place each along your wave by hand.
- Type the word and duplicate the layer once for each letter, or type each letter as its own text layer.
- Delete everything but one letter on each layer.
- Using the Transform tool, move each letter slightly up or down along a guide curve, and rotate it a few degrees to follow the slope.
- Group the layers and adjust spacing.
This approach keeps each letter crisp because you are only moving and rotating, not bending. It also leaves you with separate layers, which is valuable if you plan to animate later. The tradeoff is time. A long phrase takes a while, and spacing needs careful visual checking since the wave changes how letters sit next to each other.
Best for: short words, logotypes, and anything headed to animation.
Tips for Clean Wavy Lettering
- Check legibility at small sizes. Zoom out or view the canvas at thumbnail scale. If the word reads poorly, reduce amplitude.
- Match wave to letterform. Rounded fonts tolerate bigger waves. Sharp serifs and thin strokes show kinks quickly.
- Mind your baseline. A gentle wave looks intentional. A wave that also changes letter height can look accidental, so keep scale consistent.
- Add outlines last. If you want a stroke or drop shadow, apply it after distortion, ideally on a separate layer underneath, so the effect follows the new shape.
- Keep a flat backup. Save a copy of the finished lettering as a PNG with a transparent background before you experiment further.
Taking Wavy Lettering Into a Motion Pipeline
For motion work, a static wave is often only the starting point. Export your Procreate artwork in a format that preserves transparency, and export letters on separate layers if you used the letter-by-letter method.
In After Effects you have two general options for a wave:
- Effects on rasterized lettering. Apply a wave-style effect to a rasterized lettering layer for an animated wave that travels across the word.
- Text animators. If you can reproduce the type live in After Effects, animating the live text offers a fully editable alternative that stays vector-sharp.
The practical rule is to use Procreate when the lettering itself is the artwork, meaning hand-drawn character, custom distortion, or illustrative treatment. Use After Effects text tools when the wave is purely a motion behavior and the wording may change.
If you want both, bring in the Procreate artwork for the look and animate it in After Effects. For separate letters, offset their timing so the wave ripples across the word.
Where Styleframe Fits in This Workflow
Styleframe is useful once your wavy lettering needs to become moving, stylized footage rather than a static asset. It is an AI video and motion tool built around artist control, not one-click generation. Treat the AI output as one layer in your pipeline, not a replacement for it. Your Procreate lettering remains the art-directed source.
Quick Troubleshooting
The wave looks lumpy. Use Warp with a guide curve instead of freehand Liquify, or undo and reduce brush size.
Letters look stretched. Move top and bottom control points together, and reduce amplitude.
Edges look soft. Your canvas is too small. Rebuild the lettering on a larger canvas, since upscaling afterward will not restore crisp edges as well as drawing larger would.
You need to change the wording. Go back to the hidden editable duplicate and repeat the distortion. This is why the backup layer matters.
Choosing a Method
- Pick Liquify for speed and an organic feel.
- Pick Warp for symmetrical, controlled shapes.
- Pick letter-by-letter offsets when you want crisp edges or plan to animate individual characters.
Whichever you choose, keep your editable text, work large, and decide early whether the wave is part of the artwork or part of the animation. That decision determines whether the effect belongs in Procreate or in After Effects.