How to Make the Opacity Lower in Procreate
StyleFrame Team7 min read
To lower opacity on a layer in Procreate, open the Layers panel, tap the "N" next to the layer name, and drag the opacity slider to the left. Alternatively, tap the layer with two fingers and slide left across the screen. To lower the opacity of a brush, drag the lower slider in the Sidebar downward. Each method works on a different target (brush, layer, or selection), so pick the one that matches what you want to change.
What opacity means in Procreate
Opacity controls how visible a pixel or group of pixels is. At 100%, content is fully visible. At 50%, it is half see-through. Procreate applies it at three levels, and only some of them stay editable.
- Brush opacity sets how transparent new strokes are as you paint.
- Layer opacity sets the transparency of everything on a layer, and you can change it as many times as you like.
- Selection opacity sets the transparency of a selected area on a layer, and it is committed when you finish.
Knowing which of these you need saves a lot of undoing.
Method 1: Lower the opacity of a layer
This is the most common case, and there are two ways to do it. Both start by tapping the Layers icon in the top right corner (the two overlapping squares).
Use the "N" menu
- Open the Layers panel and find the layer you want.
- Tap the letter on the right side of the layer row. It reads "N" by default.
- Drag the opacity slider at the top of the menu to the left to make the layer more transparent. The percentage is shown beside the slider.
This menu also holds the blend modes, so it is the right place if you are adjusting both at once.
Use the two-finger gesture
- Open the Layers panel.
- Tap the layer with two fingers at the same time. Your index and middle finger work well.
- An opacity bar appears at the top of the screen. Slide a finger left to lower opacity and right to raise it.
You can slide with a finger or with the Apple Pencil. The gesture is faster than the menu once it becomes habit, but the menu gives you a more precise, visible slider.
Layer opacity is non-destructive
Because you can reopen the slider and change the value at any time, layer opacity is non-destructive. The pixels themselves are not altered, so you can move from 40% to 80% tomorrow with no quality loss. Whenever you can, use layer opacity rather than baking transparency into the artwork.
Method 2: Lower the opacity of a brush
If your new strokes come out too solid, change the brush rather than the layer:
- Select the brush you want to use.
- Find the sliders on the Sidebar. The lower one controls opacity.
- Drag the lower slider downward to reduce brush opacity. Drag it upward to increase it.
This only affects strokes you make after the change. Existing strokes keep their current opacity.
When a brush looks too faint
The opposite problem comes up often. If the brush opacity is at maximum but strokes still look transparent, pressure sensitivity is probably the cause. Many brushes respond to Apple Pencil pressure, so a light touch gives a lighter mark regardless of the slider. Press harder, or check the brush's pressure settings, before assuming the slider is broken.
Method 3: Lower the opacity of a selection
Sometimes you only want part of a layer to fade, such as one shape on a layer that holds several elements. Procreate handles this through selections:
- Open the Selection tool and choose your preferred method at the bottom.
- Make the selection on the canvas.
- Open the Layers panel and tap the layer containing the selected paint with two fingers.
- Slide a finger left on the canvas to lower the opacity of the selected area.
The catch: this one is destructive
When you exit this mode, Procreate applies the change. You can undo it immediately, but you cannot reopen it and adjust the value repeatedly the way you can with layer opacity. Every application is final. If you think you will want to tweak the result later, move the selected content to its own layer first (copy and paste it, or cut it to a new layer) and use layer opacity instead.
If the two-finger tap undoes your stroke
A common complaint is that the two-finger tap triggers undo and removes the last mark. This happens when you tap the canvas instead of the layer row. The two-finger tap has to land on the layer in the Layers panel, the same spot where you would normally tap once to open the layer options. If you are working with an active selection, the opacity slider in the "N" menu will still change the whole layer, so use the two-finger gesture when you want to affect only the selection.
Method 4: The Adjustments > Opacity tool
Older versions of Procreate documented a dedicated tool for this. Tap Adjustments, then Opacity, and a blue "Slide to adjust" bar appears at the top of the screen showing the layer's opacity, starting at 100%. Slide left to make the active layer more transparent. Buttons along the bottom let you cancel, undo, redo, or reset, and tapping the Adjustments icon again (or choosing another tool) commits the change.
Users have reported that in newer versions, opacity is handled through the layer gestures and menus described above, and that the old per-selection behavior now requires the two-finger tap. If your version of the app lacks this adjustment, use Methods 1 and 3.
Quick reference: which method to use
Practical habits that keep opacity editable
- Separate elements onto layers. If you might fade something later, give it its own layer so you can use layer opacity instead of a selection.
- Use clipping masks. A clipping mask layer only paints inside the layer beneath it, so you can build up soft, semi-transparent shading without touching the base artwork. Combine this with a lowered brush or layer opacity for subtle glazing.
- Build with low brush opacity. Layering several low-opacity strokes gives smoother gradients and more control than one heavy stroke.
- Name your layers. When you have dozens of layers at different opacities, labels help you find the one you need.
Taking low-opacity Procreate art into a motion pipeline
If you work in After Effects, Premiere Pro, or Nuke, Procreate is often a source for textures, overlays, character art, or hand-drawn elements rather than the final stage. Opacity decisions matter there too.
Before you export, decide whether opacity should be baked in or stay adjustable. Keeping elements on separate layers at 100% and lowering opacity later in your compositor gives you keyframeable, non-destructive control, which Procreate's slider cannot provide on its own. If a look depends on the exact transparency you painted, check after import that opacity and blend modes survived the trip, since different formats and apps handle them differently.
Troubleshooting common opacity problems
The slider does nothing. Confirm the correct layer is active, and that it is not locked. Remember that the brush slider only affects strokes you paint after changing it.
Strokes look faint even at 100%. Check Apple Pencil pressure and the brush's own settings. Many brushes respond to pressure, so a light touch lowers opacity.
The whole layer faded, not my selection. The "N" menu slider always changes the full layer. Use the two-finger tap on the layer to affect only the selection.
Two-finger tap undoes my last stroke. Tap the layer in the Layers panel, not on the canvas.
I can't re-edit a faded selection. Selection opacity is committed on exit. Undo right away if needed, or redo the change on a separate layer using layer opacity.
Summary
Lowering opacity in Procreate comes down to choosing the right target. Use the Sidebar's lower slider for brushes, the "N" menu or a two-finger tap for layers, and a selection with a two-finger tap for part of a layer. Remember that only layer opacity stays editable, so structure your artwork on separate layers if you expect to revise it. If the art is headed into a motion project, keep the transparency flexible until you reach your compositing app.