How to Make the Brush Size Smaller on Procreate Pocket
StyleFrame Team6 min read
On Procreate Pocket, drag the top Brush Size slider on the left edge of the canvas downward to make the brush smaller. For finer control, press and hold the slider, slide your finger sideways away from it without lifting, then drag up or down. The size changes in much smaller increments the further your finger is from the slider.
The Fast Way: Use the Brush Size Slider
Procreate Pocket puts two sliders on the left side of the screen by default. The top one controls brush size and the bottom one controls opacity or pressure.
- Open a canvas and make sure you're on the tool you want to change (paint, smudge, or erase).
- Place your finger on the top slider handle.
- Drag down to shrink the brush. Drag up to enlarge it.
- Release, then test a stroke on a spare layer or an empty part of the canvas.
If you want a tiny brush for linework, drag close to the bottom of the slider and then fine-tune from there.
Make Finer Adjustments
The slider is short, and on a phone screen a few pixels of finger movement can jump the size by a lot. To slow it down:
- Touch and hold the size slider handle.
- Without lifting your finger, move it sideways, away from the slider.
- Keep your finger down and drag up or down.
The further your finger is from the slider, the smaller each increment becomes. This is the quickest way to move from, say, a 6 px brush to a 4 px one without overshooting. Practice it a few times, because it becomes muscle memory quickly.
If the Slider Seems to Do Nothing
Several common situations make it look like the size isn't changing.
You're on a different tool than you think
Paint, smudge, and erase are separate tools. If you shrink the paint brush and then switch to erase, the eraser may use a different brush and size. Expand the toolbar with the ellipsis icon to see which tool is active, then adjust the size for that tool specifically.
The sliders aren't where you expect
The sliders sit on the left by default. If someone has switched the interface to the left-hand layout, they will be on the opposite side. You can change this by expanding the toolbar with the ellipsis, tapping Actions (the wrench icon), and checking your Prefs for interface options.
You're adjusting the wrong slider
The lower slider affects opacity or pressure, not size. On iPhones with 3D Touch, it changes opacity by default. On devices without it, it defaults to pressure. Holding that slider button until you feel a haptic tap (or see it pulse visually) swaps between the two modes. If your strokes look faint rather than thin, this is likely the cause.
The brush itself may limit the size
Some brushes may not go as small as you want. If the smallest setting is still too big, try a different brush, or open the brush in Brush Studio and review its settings. Duplicate the brush before editing it so the original stays intact.
Brush Studio Settings That Change How "Small" Feels
Even at the same pixel size, a brush can look thicker, rougher, or more erratic depending on other attributes. If a small brush still isn't giving you clean thin lines, check these.
Spacing
Spacing sets how often the brush shape is stamped along your stroke. With wide spacing you see distinct shapes with gaps between them. With no spacing the stamps merge into a continuous line. For thin, fluid lines, lower the spacing.
StreamLine and Stabilization
StreamLine smooths wobbles and is especially useful for inking and calligraphy. Stabilization takes a moving average of the stroke, so higher values give straighter, calmer lines. Motion Filtering is Procreate's more advanced take on the same problem, trimming the extreme wobbles instead of averaging them. Thin lines expose shaky hands more than thick ones do, so a small brush often benefits from a bit of smoothing. You can apply these per brush or globally through Prefs under Actions.
Jitter
Jitter offsets each stamp by a random amount. A little roughens the edge, and a lot scatters shapes around the path. If your small brush looks fuzzy or scattered, turn Jitter down or off.
Fall Off
Fall Off fades the stroke out as it goes. If your thin lines vanish halfway, this setting may be responsible. Turn it off for consistent opacity along the stroke.
Practical Habits for Small, Precise Work
- Zoom in instead of shrinking endlessly. A tiny brush on a zoomed-out canvas is hard to control. Zoom in, use a moderate size, and your strokes will be proportionally smaller when you zoom back out.
- Keep a dedicated fine-line brush. Duplicate a brush you like, set its spacing, StreamLine, and size for detail work, and name it clearly. You'll avoid constantly re-tuning the slider.
- Test on a scratch layer. Make a quick stroke on a throwaway layer to check size and smoothing before touching your artwork.
- Work at a higher canvas resolution if the piece will be scaled. Thin lines that look right on a phone screen can become heavy or soft when scaled up in a compositing app.
Why This Matters for Motion and VFX Work
Many motion designers and compositors use Procreate Pocket as a quick sketchpad: thumbnails for storyboards, hand-drawn accents, rough mattes, paint-over notes on frame grabs, or small texture elements. In those cases, brush size consistency matters because the artwork usually ends up in After Effects, Premiere Pro, Cinema 4D, Blender, or Nuke, where line weight affects how elements scale and animate.
A few things to keep in mind when you export:
- Transparent PNGs keep hand-drawn elements isolated so they can sit over footage or 3D renders. Hide the background layer before exporting.
- Consistent line weight across a set of elements keeps them looking like they belong together once placed in a comp. Note the size values you use, or keep the same custom brush for the whole set.
- Resolution should match or exceed your comp size for any element you might scale up. Fine lines get soft quickly if you enlarge them.
- Layer organization helps. Separating elements onto their own layers makes it easier to export variations or animate pieces individually.
Quick Troubleshooting Checklist
Summary
To make the brush smaller in Procreate Pocket, drag the top slider down, and use the hold-and-slide-sideways technique for precision. If the result still isn't what you want, check which tool is active, which slider you touched, and whether the brush's own settings (spacing, StreamLine, Jitter, and Fall Off) are shaping the line. A small amount of setup in Brush Studio gives you a reliable fine-line brush that you can carry into any downstream workflow, whether that's a storyboard, a paint-over, or a set of elements bound for your compositing app.