How to Make Text Around in Procreate
StyleFrame Team7 min read
Procreate has no text-on-a-path feature, so you make text go around a circle or curve by faking it: add text, rasterize it, then bend it with the Warp tool (or rotate letters one at a time) against a circle or arc guide you draw yourself. Warp is fastest for gentle arcs. Manual letter placement is more precise for full circles and badge-style logos. Procreate is best for hand-lettered or stylized results.
Why Procreate Can't Do This Natively
Photoshop and Illustrator let you click a path and type along it. Procreate's text tool doesn't. You add text through Actions > Add > Add Text, and it sits in a bounding box that you can move, resize, and transform uniformly. The box can't follow a curve.
Because of that, every method below is a workaround. You build a visual guide, such as a circle or an arc, and then deform or arrange the text to match it. Once you accept that, the choice is between speed (Warp) and control (letter-by-letter placement).
Before You Start: Vector vs. Raster Text
Procreate keeps new text as vector until you rasterize it. Vector text lets you retype, change font, adjust spacing and alignment, and scale without quality loss. But several tools need pixels to work. Rasterizing turns the text into a normal layer you can distort, paint on, and merge.
The practical rule is to finalize everything typographic first: the font, weight, and kerning. Rasterize only when you're ready to bend it. After that, a typo means starting the text again.
Some prep that pays off:
- Pick a font with some weight. Thin strokes can break up when stretched along a tight curve.
- Increase kerning before you curve. Text on the inside of a curve gets compressed, and letters crowd together. Open spacing in the Design settings gives you headroom.
- Keep the text on a single line. Drag the bounding box nodes wider so it doesn't wrap.
Set Up a Circle or Arc Guide
A guide shape is what makes the result look deliberate instead of eyeballed.
- Create a new layer and draw a circle with a mono-line brush.
- Hold two fingers on the canvas after drawing. Procreate snaps the stroke to a circle shape, and you can resize it before releasing.
- For centering, turn on the Drawing Guide in the Canvas section of Actions, open Edit Drawing Guide, and raise the grid size. The center lines make it easy to align the circle to the middle of your canvas.
- For text that wraps both the top and bottom of a badge, duplicate the circle and shrink the copy. The gap between the two circles should roughly equal your letter height, so the text sits between them.
- Group the guides and lower their opacity so they don't distract.
For a simple arc, draw one with the same snap-to-shape behavior, then use Edit Shape to adjust its nodes until it looks symmetrical.
Method 1: Warp the Text Along the Guide
This is the quickest approach and works well for banners, arcs, and slight curves.
- Add your text and set the font, style, and kerning.
- Move the text layer above your guide layer, then center it over the arc using the transform bounding box and the center guideline.
- Open the Transform tool and choose Warp from the menu at the bottom. A mesh of nodes appears around the text.
- Drag nodes (or any part of the mesh, even where there's no node) to pull the text down around the arc.
- Turn on Advanced Mesh for more control points. More nodes mean smoother bends, especially for longer lines.
If you're curving text around a full circle, Warp gets fiddly. The mesh has to stretch the text more than a simple arc requires, and letter shapes distort. For half-circles and gentle curves it's fine. For anything close to a complete ring, switch to Method 2.
Tips for cleaner Warp results
- Work in small adjustments. Pull the ends down first, then refine the middle.
- Check the baseline against your guide, not the tops of the letters.
- Zoom in on letter edges after you've finished. If anything looks stretched, undo and add more mesh nodes.
Method 2: Place and Rotate Each Letter
For a true circular badge, this is the most reliable approach. It's slower but gives you full control over spacing and angle.
- Type the text, then split it so each letter (or small group of letters) is on its own layer. Rasterize them as needed.
- Starting at the top center of your guide circle, position the first letter so its baseline touches the guide.
- Use the Transform tool to rotate each following letter so it points outward from the circle's center. Move it along the circle edge to the right spacing.
- Work from the middle outward when you have a phrase that should be symmetrical, placing the middle letters first and then moving to each side.
- For text on the bottom of a circle, decide whether the letters should read left to right along the bottom (tops facing the center) or follow the top's orientation. Bottom text usually reads better when its baseline sits on the outer guide.
This method is also how you avoid awkward distortion. Each letter stays undistorted, since you're only moving and rotating it. The trade-off is time, so it makes sense for logos and key lettering and less sense for throwaway text.
You can also apply the same idea to hand lettering. Draw the lettering on a straight line, then use either method to bend it, or just letter directly on the curve if that feels more natural.
Method 3: Letter Directly on the Curve
If your project is illustrative rather than typographic, skip the text tool. Use your circle guide as a visual reference and hand-letter along it with a brush. You lose font consistency but gain organic spacing, and imperfections read as intentional in hand-lettered work. Many badge and emblem designs are done this way.
Clean Up and Finish
Once the text follows the guide:
- Delete or hide the guide layers.
- Check the spacing optically. Curved text often needs individual letter nudges even when the math is right, especially around letters like "A," "V," and "T."
- Group the final text layers so they're easy to move together.
- Use clipping masks or layer masks if you want to add texture or color fills to the lettering without destroying it.
- Keep a copy of the layered file before you flatten anything. If you rasterized the text, that copy is your only way back to editable type.
Taking Procreate Lettering Into a Motion Workflow
For motion designers, Procreate is usually the lettering stage and not the final one.
Use Procreate for characterful lettering. When the lettering is hand-drawn, warped, or textured, curve it in Procreate and export it as a transparent PNG or a layered file. Export letters on separate layers if you want to animate them individually in your animation software. Splitting the letters during Method 2 sets you up for that automatically.
Plan for resolution. Procreate canvases are fixed-size rasters once text is rasterized. If you'll scale the lettering up in a 4K comp, make the original canvas large enough to hold up. Otherwise you'll soften edges when you scale.
Export clean alpha. Hide the background and any guides, then export a PNG so you have clean transparency to drop into your compositing or editing software.
Quick Troubleshooting
- Letters look jagged after warping. Your canvas is probably too small. Redo the lettering on a higher-resolution canvas.
- The curve looks lopsided. Re-check that your guide circle is centered using the drawing guide's middle lines, and use Edit Shape to correct the arc.
- Spacing looks uneven. Adjust kerning before rasterizing, or nudge individual letters in Method 2.
- A tool is grayed out for text. Rasterize the text layer first.
Choosing the Right Method
Start with Warp to see whether it gets you there. If the letters distort or the curve gets tight, move to manual placement. Either way, a clean guide and generous kerning will do more for the final result than any single tool setting.