How to Make Signature Brush in Procreate
StyleFrame Team7 min read
To make a signature brush in Procreate, write your signature in a high-resolution canvas, copy it, and paste it into a new brush's Shape source in Brush Studio. Then set Stroke Path spacing to maximum, turn Apple Pencil pressure opacity off, and enable Stamp Preview so the brush places your whole signature with a single tap. The whole setup takes a few minutes, and you can reuse the brush on every illustration, style frame, or end card you finish.
What You Need Before You Start
- Procreate on an iPad.
- An Apple Pencil or a steady finger for writing the signature itself.
- A signature, logo mark, or watermark you're happy with. The brush will reproduce it exactly, so spend time on the design first.
Plan for resolution. A signature drawn small may look soft when you stamp it large. A canvas of 2000 px wide is a workable minimum, and 3000 × 3000 px gives you headroom for large prints or 4K deliverables.
Step-by-Step: Build the Signature Brush
1. Create the Source Canvas
Create a new square canvas, ideally 3000 × 3000 px. Square canvases are easier to center.
Fill the background with black. On a new layer above it, write your signature in white. Use a brush with clean, consistent edges, such as a monoline or a lightly textured inking brush, rather than something with heavy grain. Grain in the source becomes grain in every stamp.
Make the signature fill most of the canvas without touching the edges. A tight composition means the stamp wastes less space and scales predictably later. Turn on Snapping and Magnetics, with both turned all the way up, to center it precisely. A signature that sits off-center will land off-center relative to your cursor every time you stamp.
2. Copy the Artwork
With the signature layer selected, use the three-finger swipe down gesture to open the Copy & Paste menu and choose Copy All (sometimes labeled Copy Canvas).
3. Create a New Brush
Open the Brush Library. Either create a dedicated brush set (tap the + at the top of the set list) or pick an existing set. A custom set called "Signatures" or "Branding" is a good idea if you plan to make several variants.
Inside the set, tap + to open Brush Studio with a new brush.
4. Import the Shape Source
In Brush Studio, open the Shape tab, tap Edit, then Import, then Paste. Your signature appears in the shape editor.
Check the polarity. If your design shows as a white background with a black design, tap the image with two fingers to invert it to a black design on a white background. Then tap Done and wait for the preview to refresh.
5. Turn the Brush Into a Single Stamp
A normal brush repeats its shape along a stroke. For a signature you want exactly one impression per tap. Make these changes:
- Stroke Path: Drag Spacing all the way to the maximum. This lets the brush act as a single stamp rather than a line.
- Apple Pencil: Set the pressure Opacity slider to none, so the signature is always fully opaque no matter how lightly you tap.
- Properties: Raise the Maximum Size slider as high as it goes. This lets you stamp the signature large on big canvases without hitting a ceiling.
- Properties > Preview: Enable Use Stamp Preview so the brush thumbnail in the library shows your actual signature rather than a generic stroke.
You might also check Stroke Path's jitter and Streamline values, plus Taper settings, to ensure nothing distorts the shape. Defaults on a new brush are generally fine, but a leftover taper from a duplicated brush can make a signature look clipped.
6. Tune Preview Size and Maximum Size
Two settings depend entirely on how you drew the signature:
- Preview size controls how large the signature appears in the brush set thumbnail. Adjust it until the entire signature fits inside the preview.
- Maximum size controls how large the stamp can become on canvas. If you work on a huge file, such as a 20-inch canvas, and can't make the signature big enough, this is the setting to raise.
Test on a scratch canvas. Stamp at small, medium, and large sizes and check that edges stay crisp.
7. Name and Pin the Brush
In the About this Brush tab, add your name and any notes. Back in the Brush Library, tap and hold the brush to rename it. Choose something obvious, like "Signature – White" or "Signature – 2025."
To keep it handy, open Recents, swipe left on the brush, and tap Pin. It stays at the top of the Recents list so you never dig through sets mid-project.
Troubleshooting Common Problems
The stamp appears as a line of repeated signatures. Spacing isn't at maximum. Return to Stroke Path and push it fully right.
The signature is faint or varies with pressure. Pressure opacity is still active in the Apple Pencil tab. Set it to none, and check that the brush's Properties don't add a minimum opacity below 100%.
The edges look soft or jagged. The source was too small or heavily blurred. Redraw at a larger canvas size and avoid scaling the pasted image in the editor.
The signature is cropped. The artwork touched the edges of the source canvas. Leave a small margin and recopy.
The stamp comes out in the wrong color. Check the color you have selected before tapping. For fast switching, make two brushes (light and dark) or keep a color history swatch for each.
Useful Variations
- Initials-only version. A compact monogram works for small corners or social crops.
- Full-name version. Better for finished prints and portfolio pieces.
- Logo lockup. Use a separate brush for studio branding so you don't mix personal and client marks.
- Textured version. Add a grain or ink-bleed texture to the source so the signature feels hand-applied on traditional-styled pieces.
Duplicate your working brush before experimenting so the original stays intact.
Taking the Signature Into a Motion Pipeline
If you work in After Effects, Premiere Pro, Cinema 4D, Blender, or Nuke, the Procreate brush is mainly a tool for finishing stills, boards, and style frames. For video work, a few habits help:
- Stamp on its own layer. Put the signature on a separate transparent layer so it never bakes into the artwork. Export a PNG with the background hidden to keep the alpha channel.
- Export a clean signature asset. Stamp it once on an empty canvas and export a transparent PNG at 3000 px or larger. Import that into After Effects as a footage item for end cards, lower thirds, or watermarks.
- Keep it in a safe area. If a frame will be cropped for different aspect ratios, keep the signature inside title-safe margins.
- Animate it in your compositor. A simple write-on can be built with a Reveal mask or a Shape Layer trim path in After Effects. For something that looks more drawn, screen record yourself writing the signature in Procreate and use that as a plate.
- Match color management. Check your Procreate canvas color profile against your After Effects project color space to avoid shifted blacks or tinted whites on the signature.
Where Styleframe Fits in the Workflow
A signature brush helps you finish illustrated frames consistently, but Procreate isn't where you'd extend those frames into motion. is an AI video and motion tool. You can start from a Procreate painting or style frame and use it as a reference image.
That means the signature stays where it belongs, as a final compositing layer in After Effects or Nuke, over footage you can grade, track, and finish in your usual pipeline.
Quick Checklist
- Draw the signature in white on black at 2000–3000 px.
- Center it and leave margins.
- Copy the canvas.
- New brush > Shape > Edit > Import > Paste.
- Invert if needed, then Done.
- Spacing to max, pressure opacity to none, Maximum Size up, Stamp Preview on.
- Adjust preview size, name the brush, and pin it in Recents.
- Export a transparent PNG for motion projects.
Once the brush is set up, signing a piece takes one tap. Keep the source file so you can regenerate the brush if you update your signature or switch devices.