How to Make Shape Clipping Mask Procreate
StyleFrame Team7 min read
To make a shape clipping mask in Procreate, draw a shape on a base layer (hold your stroke to snap it with QuickShape), add a new layer above it, tap that layer, and choose Clipping Mask. Anything you paint on the upper layer now shows only where the shape has pixels, and a small down arrow on the layer confirms the link. Because the shape stays on its own layer, you can move, erase, or redraw it later and the clipped artwork updates with it.
What a shape clipping mask does
A clipping mask confines one layer's content to the visible pixels of the layer directly beneath it. The lower layer is the base layer, and it acts as the boundary. The upper layer can hold anything: texture, gradients, lettering, photo reference, or shading. Whatever extends past the base shape is hidden rather than deleted.
That non-destructive behavior is the main reason to prefer it over the eraser. If you trim a texture to a circle with an eraser, the trimmed pixels are gone. If you clip the same texture to a circle, the full texture still exists on its layer, so you can slide it around inside the shape or resize the shape later.
Step-by-step: build a shape clipping mask
1. Create the base shape layer
Start a new layer and name it something clear, such as "Base Circle." Naming matters once you have several clipped layers stacked up.
Draw your shape with the Apple Pencil or your finger. For geometric shapes, use QuickShape: draw a rough circle, oval, triangle, or rectangle and hold at the end of the stroke without lifting. Procreate snaps the stroke to a clean shape. Tapping Edit Shape lets you refine it, and with the shape finished you can ColorDrop a fill into it.
Filling the shape matters. A clipping mask follows the pixels that exist on the base layer, so an outline-only circle will reveal content only along the thin line. For a solid window, fill the whole shape.
2. Add the layer you want to clip
Tap the plus icon in the Layers panel to add a new layer above the base. This is where your texture, color, or artwork goes. You can paint on it directly, or import a photo or other artwork onto that layer.
If you already have the artwork on its own layer, make sure it sits above the shape in the stack. The clipping direction is always downward: a layer clips to what is below it.
3. Apply the clipping mask
Tap the upper layer to open the Layer Options menu, then tap Clipping Mask. The layer shows a small arrow pointing down toward the base. Your artwork is now visible only inside the shape.
A shortcut worth knowing: if you create a new layer directly above a base layer that already has clipped layers, Procreate may clip the new one automatically. This is convenient, but it also means you should check for the arrow before painting, in case you wanted a free layer.
4. Adjust each layer independently
Because the base and the clipped layer are still separate, you can:
- Move or rotate the clipped artwork to change what appears inside the shape.
- Recolor the clipped layer without touching the base.
- Erase part of the base shape and see the clipped content disappear in the same area.
- Clear the base layer and draw a new shape on it, so the clipped content "appears" wherever you paint.
That last behavior is useful for reveal-style effects, where you paint a window and the content shows up inside it.
To remove the clip, tap the layer and tap Clipping Mask again. The artwork returns to its full, unclipped state.
Stack clipping masks for texture, shading, and highlights
Clipping masks are stackable, which is where they become practical for production work. A typical stack on a single shape might be:
- Base shape (flat color)
- Clipped texture layer
- Clipped shadow layer
- Clipped highlight layer
Every clipped layer sits above the same base and is confined to it. You can reorder them by dragging, hide them individually, lower their opacity, or change their blend modes. Experiment with blend modes to find what suits your piece.
One rule to remember: a clipped layer locks to the nearest layer below it that is not itself clipped. All the layers in a continuous clipped stack therefore share the same base. If you want stars inside a dotted pattern inside a leaf, you can't do it with simple stacking, because everything clips to the leaf.
Clipping mask vs. Alpha Lock vs. Layer Mask
These three tools overlap, and choosing the wrong one is a common source of frustration.
Alpha Lock doesn't use an extra layer, but it changes the original pixels, so it is the more destructive of the three. Clipping masks cost you additional layers, which matters because Procreate has layer limits. Layer masks are the right call when you need soft, gradient-based transparency rather than a hard shape boundary.
A practical approach: use Alpha Lock for quick flat-color changes, clipping masks for anything you might revise, and Layer Masks when you need feathered edges.
Troubleshooting common problems
The clipped content disappears completely. The base layer is probably empty or hidden. Check that the layer below has visible pixels where you expect the content to show.
Only the outline of the shape is revealing content. The base shape is unfilled. ColorDrop a fill into it.
Clipping stops working after grouping. If you separate a clipped layer from its base by placing it in a different group, the relationship breaks. Keep the base and its clipped layers together in the same group.
You need to clip a layer to something that is itself clipped. A simple stack won't do this. Two workarounds: select the base layer's contents (tap and hold the layer with two fingers) and paint on a new layer with that selection active, or duplicate and flatten a group to create a new base. If you may revise the base later, convert the selection into a Layer Mask instead so the full strokes stay editable.
You are running out of layers. Merge finished clipped layers into their base once you are happy with them, but save a duplicate group first so you can go back.
Moving Procreate shape work into a motion pipeline
Procreate is a fast place to build shapes, textures, and hand-drawn elements, but animation happens elsewhere. If you plan to animate your clipped artwork, a few habits will save time later:
- Keep the layers separate. Export the layered file rather than a flattened image, so the base shape and the clipped texture can move independently.
- Rebuild the clip in your compositor. Verify how your file imports, since clipped layers may arrive differently depending on the format, and be ready to rebuild the relationship between the shape and the texture.
- Name layers deliberately. "Base Circle," "Texture Clip," and "Highlight Clip" are far easier to rebuild than "Layer 14."
- Export textures at the resolution you need. Plan for the largest scale the element will reach in the comp.
Where Styleframe fits
Procreate gives you precise, hand-controlled stills. is a tool you can look at when you want to take stills like these further into motion.
Quick recap
- Draw and fill a shape on its own layer; use QuickShape for clean geometry.
- Add a layer above it and choose Clipping Mask from the Layer Options menu.
- Look for the down arrow to confirm the clip.
- Stack multiple clipped layers for texture, shadow, and highlights, adjusting blend modes and opacity as needed.
- Use Alpha Lock for quick edits and Layer Masks for soft transparency.
- Keep layers separate and well named if the artwork is headed into After Effects or another compositor.