How to Make Shape Brushes in Procreate
StyleFrame Team7 min read
To make a shape brush in Procreate, open Brush Studio with the + button in the brush library, tap Shape Source, and import a square, high-resolution image with the design in white on black. Then set Spacing under Stroke Path high enough that each stamp reads as a separate shape. White in the source image paints and black stays transparent, so a common cause of failed brushes is an inverted or transparent source.
What a shape brush actually is
In Procreate, every brush combines two ingredients: a Shape, the tip that gets stamped along your stroke, and a Grain, a texture that shows through the shape. A shape brush, often called a stamp brush, uses a recognizable form such as a star, a leaf, a logo mark, or a hexagon as that tip. Spacing is set wide enough that each stamp stays distinct instead of smearing into a line.
Because the brush engine only reads luminance, the shape is a grayscale mask. White is fully opaque, black is fully transparent, and grays are partial opacity. Once that clicks, most of the rest is settings.
Prepare the shape artwork
Preparation matters more than any slider in Brush Studio. Do this before you open the editor:
- Use a square canvas. A non-square source gets distorted when Procreate fits it to the brush tip.
- Work large. A canvas around 10 × 10 inches at 300 dpi gives you a sharp stamp, even at big brush sizes. Small sources turn soft when you scale the brush up.
- Stick to pure black and white for a crisp, fully opaque stamp. Mid-grays produce a semi-transparent result, which is useful when you want soft edges but surprising when you don't.
- Draw the shape in white on a black background. If you draw it black on white, you can invert it later, but starting white-on-black saves a step.
- Leave a margin. Keep the shape away from the canvas edge so the stamp doesn't clip at its bounds.
JPG or PNG?
A common trap is importing a PNG with a transparent background and a black design. Procreate reads black as transparent, so the whole image becomes an empty tip and the brush paints nothing. There are three fixes:
- Save the artwork as a JPG with a solid background.
- Put a flat white or black background behind the design before exporting.
- If you do use transparency, make the design white.
Build the brush step by step
- Duplicate first. In the brush library, swipe left on a simple brush such as a basic pen and tap Duplicate. You keep a safe original and start from sensible defaults.
- Open Brush Studio. Tap the duplicate, or tap + for a new brush, to enter Brush Studio.
- Open Shape. Tap Shape in the left sidebar, then Edit next to Shape Source. On smaller screens you may tap the shape preview directly.
- Import your artwork. Choose Import and pick from Photos, Files, the built-in Source Library, or paste from your clipboard. Procreate's Source Library has over 150 stock shapes, which works well for testing before you commit your own art.
- Invert if needed. If the preview looks like a negative of what you wanted, tap the source with two fingers to invert it.
- Set a neutral grain. For a clean solid stamp, pick a plain white or flat grain source so no texture breaks up the shape. A textured grain gives a printed, distressed look.
- Tap Done and test on a blank canvas.
- Name and save. In About This Brush, rename it and add your signature if you like. Put it in its own brush set so it's easy to find and share.
Tune the stamp behavior
The raw import usually looks wrong until you adjust how it's laid down. The settings that matter most:
- Spacing (Stroke Path): Raise it until each stamp separates. At low spacing you get a continuous painted ribbon; at high spacing, discrete shapes. It's the first thing to adjust.
- Orient to screen: Turn this on if you want the shape to stay upright no matter which way you drag. Leave it off for shapes that should rotate with the stroke, such as arrows following a path.
- Rotation and Scatter (Shape behavior): Add Rotation jitter or Scatter for organic variety, like leaves or confetti. Keep both at zero for precise geometric stamps.
- Size limits (Properties): Set the maximum so the shape can reach the sizes you actually need, and the minimum so small stamps stay legible.
- Pressure and tilt dynamics: Map size or opacity to Apple Pencil pressure if you want expressive control. Switch dynamics off for a consistent stamp every tap.
- Streamline: Mostly useful for line-based brushes, but it can steady a stroke that places stamps along a curve.
Change one setting at a time and test after each change. Brush Studio gives you a live preview pad, so use it.
Make a reusable set of geometric shape brushes
Shape brushes are especially handy as quick stand-ins for shape tools, which Procreate doesn't offer in the same way vector apps do. A workable approach:
- Create one clean white-on-black source per shape: circle, square, triangle, pentagon, hexagon, star.
- Build the first brush with the settings above, with spacing high, Orient to screen on, and dynamics off.
- Duplicate that brush for each additional shape and swap only the Shape Source. Settings stay consistent across the set.
- Make outline and solid variants of each shape.
- Stamp on a dedicated layer, then use Transform to stretch a circle into an ellipse or a square into a skewed parallelogram. Transform also lets you go beyond the brush's maximum size.
Two useful variations: stamp an outline shape on one layer and hand-draw over it on another, using it as a tracing guide for natural-looking geometry. And for a straight-line tool, put a thin horizontal bar in the Grain source instead of the Shape, which produces ruled lines whose spacing follows your size setting.
Troubleshooting common problems
- The brush paints nothing or a blank square: Your source is probably a black design on transparency or a flat black image. Re-export as a white design, add a solid background, or invert it with two fingers.
- Edges look jagged or blurry: The source resolution is too low. Rebuild it larger and re-import.
- The shape looks stretched: The source wasn't square. Crop to 1:1 first.
- Shapes overlap into a smear: Increase Spacing.
- A gray halo appears around the stamp: Your source has anti-aliased gray edges or a non-pure background. Clean the artwork to pure black and white, or accept the soft edge intentionally.
- Stamps rotate unpredictably: Check Orient to screen and any Rotation or Azimuth settings.
- Import does nothing: Save the image to Photos or Files as a JPG and import from there, or copy it and use paste.
Where Procreate shape brushes fit in a motion pipeline
Procreate is an illustration tool, but its output can feed motion work. A few practical points:
- Work at the final resolution. Match canvas size to your comp, or go larger, so you don't scale up raster stamps in After Effects.
- Know the raster limit. Stamped shapes are pixels, not vectors. If you need infinitely scalable geometry, build it as shape layers in After Effects or in a vector tool, and use Procreate shape brushes for hand-made, textured, imperfect marks.
Quick checklist
- Square, large source with a white design on black
- JPG or flattened PNG, with no transparent black designs
- Shape Source for the stamp; neutral Grain for a clean result
- Spacing raised, Orient to screen set for your intent
- Duplicate before editing; save into a named brush set
Once your first brush works, building a whole set is straightforward, because every new brush reuses the same settings and only the source image changes.