How to Make Procreate Not Detect Hand
StyleFrame Team7 min read
To make Procreate ignore your hand, turn off touch drawing in Procreate (Actions > Prefs > Gesture Controls > General > Disable Touch Actions), then turn on "Only Draw with Apple Pencil" in iPad Settings > Apple Pencil. With both set, only the Pencil can make marks, so a resting palm can't paint, smudge, or erase. Procreate's Palm Support can't be switched off completely, but you can tune it under iPad Settings > Procreate with the Palm Support Fine Mode toggle.
What "not detect hand" actually means in Procreate
Procreate has no single switch labeled "ignore my hand." Accidental marks come from three separate systems, and each has its own control:
- Touch input as a drawing tool. By default, fingers can paint, smudge, and erase.
- iPadOS Apple Pencil handling. The system can be told to accept only Pencil input for drawing.
- Palm Support. Procreate's own recognition of large touches as palms, which it then rejects.
Most stray marks come from the first. If your fingers can't draw, your palm can't draw either. Palm Support matters when you still want to use your fingers for gestures like pinch-zoom, two-finger undo, or rotating the canvas while the Pencil is down.
Step 1: Disable finger painting in Gesture Controls
This is the most reliable fix. It makes touch input unable to produce marks at all.
- Open a canvas and tap Actions (the wrench icon).
- Go to Prefs > Gesture Controls.
- Open the General tab.
- Turn on Disable Touch Actions. Older versions label this option "Global Touch" or "Disable touch features – finger touches will only perform gestures." Newer versions word it as disabling painting with a finger. The result is the same: fingers only perform gestures.
- Check the Smudge and Erase tabs and make sure Touch is off for both. These are normally off by default, but a changed setting here means your hand can still smudge or erase when it can't paint.
- On the Eyedropper tab, you can disable everything except touch and hold, so a brushing palm doesn't sample colors.
After this, your fingers still pinch, rotate, and trigger two- and three-finger gestures. They just can't leave a mark.
Step 2: Turn on "Only Draw with Apple Pencil" in iPad Settings
This is an iPadOS-level setting, so it lives outside Procreate.
- Open the iPad Settings app.
- Tap Apple Pencil.
- Toggle on Only Draw with Apple Pencil.
With this on, only your Apple Pencil registers drawing input, not your hand. Combined with Step 1, you have two layers of protection. If one fails after an update, the other still holds.
Procreate also prioritizes Apple Pencil input over touch when a Pencil is in use, which is why the combination works well for most artists. If you draw with a non-Apple stylus, results vary, and you should rely more heavily on Step 1.
Step 3: Tune Palm Support Fine Mode
If you still get stray marks or your gestures misfire, look at Palm Support itself. Procreate's team has said that Palm Support is always on. It works by identifying touches of a certain size as palms and rejecting them. Because one size didn't suit everyone, they added a Fine Mode toggle.
To change it:
- Open iPad Settings.
- Scroll down the app list and tap Procreate.
- Find Palm Support Fine Mode and switch it on or off.
Fine Mode is on by default and is designed for most people. It isn't a way to disable palm rejection, only a way to change how sensitive the size detection is. Try the opposite of whatever you're currently using, then give it a day or two of normal work. You may need to adjust how you perform certain gestures. One user who had to pause before two-finger zooms, because Procreate misread one finger as a palm and drew or erased instead, reported a small improvement with Fine Mode off, though not a complete fix.
Step 4: Change how you rest your hand
Software settings only go so far. A few physical habits help:
- Plant your full palm rather than a sliver of it. Palm detection works by recognizing a palm-sized touch. A tentative contact at the screen edge can look like a normal fingertip and get through.
- Perform gestures near the middle of the screen. Users report fewer missed or misread gestures there than near the edges, where the system sometimes struggles to classify touches.
- Use a drawing glove. A drawing glove covers the part of your hand that touches the glass. It reduces both accidental touches and friction, and it's a cheap fix if the settings don't completely solve it.
- Check for screen contamination. Some users find that a freshly cleaned screen behaves differently. That is anecdotal, so treat it as something to test rather than a rule.
Troubleshooting: marks still appear
If you've done Steps 1 to 3 and still see marks, work through this list:
- Confirm the setting stuck. Updates can reset preferences. Reopen Gesture Controls and verify.
- Check for a Pencil issue rather than a palm issue. If marks appear from tilt, the cause may be brush settings. Tilt-based shading can produce broad, blunt side strokes. Edit the brush's tilt angle so it doesn't trigger unintentionally. One artist reports that the default brushes trigger tilt too easily.
- Restart and re-pair. Restart the iPad, and unpair and re-pair the Pencil if problems persist. It doesn't always fix things, but it rules out a connection issue.
- Check your iPadOS version. Beta releases may cause touch problems. Make sure Procreate and iPadOS are both current.
- Assign touch to something harmless. In Gesture Controls you can map touch actions to shortcuts like QuickMenu, so stray touches do less damage.
The reverse problem: your finger won't draw
Some artists want the opposite, and the same panel handles it. If finger painting isn't working:
- Make sure Disable Touch Actions is off in the General tab.
- Check that Touch is off under Smudge and Erase, otherwise your finger will only smudge or only erase.
- Confirm the paint tool is active, your color differs from the background, and brush size and opacity aren't at zero.
- Check that Alpha Lock isn't enabled on the layer. A checkerboard pattern on the layer thumbnail is the cue.
- Try a new canvas to rule out a file-specific problem.
Why this matters if you work in motion
For many motion designers, Procreate is where storyboards, character studies, texture passes, and style frames start. A stray palm mark on a line-art layer can mean a cleanup pass later, or a ruined frame in a hand-drawn sequence where each drawing has to hold up at full resolution. Setting up touch controls once is cheap insurance, especially if you're drawing for long sessions on an iPad Pro.
A sensible setup for production sketching:
- Disable touch painting globally and keep gestures enabled.
- Turn on Only Draw with Apple Pencil at the system level.
- Keep Smudge and Erase touch controls off.
- Test Palm Support Fine Mode once and leave it alone unless gestures misbehave.
- Save a canvas template with your layer structure, so each new board starts consistently.
Quick reference
Final notes
You can't make Procreate truly blind to your hand, because Palm Support is always on by design. But you can make hand contact harmless. Disable touch painting, enforce Pencil-only drawing at the system level, tune Fine Mode if gestures misfire, and adjust how you rest your palm. That combination solves most accidental-mark problems, and it takes only a few minutes to set up.