How to Make Procreate Brush Taper at End
StyleFrame Team7 min read
To make a Procreate brush taper at the end, duplicate the brush, open Brush Studio, and go to the Taper tab. Drag the end node of the Pressure Taper slider (Apple Pencil) or the Touch Taper slider (finger) inward, then raise the Size amount so the stroke actually thins. If only one end tapers, turn off Classic Taper at the bottom of the tab, turn on Link Tip Sizes, and check the Size slider in the Apple Pencil section.
The quick version
- In the Brush Library, duplicate the brush. Edit the copy so the original survives.
- Open the copy in Brush Studio, then select Taper in the left-hand list.
- In Pressure Taper, drag the nodes at the top of the slider to set how much of the stroke start and end is affected. Pull the end node inward to lengthen the end taper.
- Raise Size so the stroke thins across that zone.
- Adjust Tip to set how sharp the point is (blunter to the right, sharper to the left).
- Scroll to the bottom and switch Classic Taper off.
- Test on the drawing pad, then on a real canvas.
That sequence should cover many cases. The rest of this article explains why each step matters and what to check when the taper still doesn't show up.
Pressure taper vs. touch taper
The Taper tab is split into two sections, and this causes much of the confusion.
- Pressure Taper applies to pressure-sensitive styluses such as the Apple Pencil.
- Touch Taper applies to anything without pressure sensing, including a finger or a basic stylus.
They are separate settings. A brush can taper beautifully under your finger and look blunt with an Apple Pencil, or the reverse, because you may have configured only one section. One person in Procreate's own support threads followed a tutorial where the artist drew with a finger, then couldn't reproduce the look with a Pencil.
Set up the section that matches your input device. If you switch between finger and Pencil, configure both.
What each Taper control does
Understanding the controls makes troubleshooting much faster.
Taper nodes and Link Tip Sizes
The nodes at the top of each slider define how much of the stroke's start and end are affected. The left node controls the beginning and the right node controls the end. With Link Tip Sizes on, moving one node moves its partner to match. This is the fastest way to get a symmetrical taper. If you want a long, elegant exit and a short entry, turn it off and set each node independently.
Size
Size sets how much the stroke width shifts across the taper zone. A low amount barely changes the line. A high amount drives it toward a point. If your end isn't narrowing at all, this is the first slider to check, because Tip depends on it.
Opacity
Opacity fades the stroke across the taper zone, but only within the length you defined with the nodes. It works well for a soft, ink-wash exit. It is less natural than a pressure-based fade, because the fade is confined to that zone.
Pressure
The Pressure setting gives a more natural fade and more control. If you want less fade, press harder as you draw. This ties the taper to your hand rather than to a fixed profile.
Tip
Tip defines how sharp the end is, from blunt to pointed. It only has an effect once Size has an amount set, so a Tip change that appears to do nothing usually means Size is still at zero.
Tip Animation
Tip Animation animates the taper as you draw in the preview. Turning it off gives a snappier preview, and the final result is identical either way, so treat it as a preference.
Why the end still won't taper
If you've followed the steps and the end of your stroke stays blunt, work through these in order.
Classic Taper is on
This is a frequently reported culprit. Classic Taper is a legacy system, and one user reported that turning it off fixed an end that wouldn't taper. That user described spending hours before discovering it. Turn it off, then retest.
Link Tip Sizes is off, or the nodes are mismatched
If only the start tapers, check whether the end node has actually been moved from the edge of the slider. With Link Tip Sizes on, pull the start node and the end node should follow.
The Apple Pencil section overrides your taper
In Brush Studio, the Apple Pencil section has its own pressure response. If Size under Pressure is too low, the line has too little range to produce a visible thin end. Raise it and test again. Setting both size and pressure to a high value gives the taper room to work.
You're testing with the wrong input
Remember that finger and Pencil use different taper sections. If your finger tapers but your Pencil doesn't, you're likely looking at Touch Taper settings while drawing with Pressure Taper.
Stroke prediction and stabilization interfere
One user in a support thread suspected stroke prediction affects how the end of a stroke resolves. Heavy StreamLine may also affect how the end of the stroke resolves. Try lowering StreamLine, or test a short, quick flick and a slow, deliberate stroke to see whether speed changes the result.
Dynamics speed
One approach shared by experienced users is to set the brush's dynamics speed setting to a negative value. Combine this with pressure taper at both ends, high size and pressure values, and Classic Taper off. It is a community technique, not an official recipe, so treat it as something to experiment with.
A starter tapered round brush
If you'd rather start from a known-good configuration than tune from scratch, this recipe, shared by a user in Procreate's support thread, can serve as a baseline. Duplicate the default Round Brush, then:
- Stroke Path: Spacing around 3%.
- Stabilization: StreamLine Amount around 10%.
- Taper: bring the tip sizes in roughly halfway, set Size around 80%, and switch Classic Taper off.
- Apple Pencil: Size around 83%.
Adjust from there. For a watercolor or ink-brush feel, link the tip sizes, raise Size toward 100% for a very sharp point, and apply the same logic to Touch Taper if you also draw with a finger.
Taper vs. Fall Off
Don't confuse taper with Fall Off, found under Stroke Path. Fall Off fades a stroke away over its length: it starts at full opacity and disappears as it goes on. Taper shapes the width and opacity at the start and end specifically. Fall Off is useful for dry-brush trails and speed streaks. Taper is what gives linework its hand-drawn start and finish. If you use both on one brush, change one at a time.
When to skip the settings and use pressure
Taper settings are a profile, not a performance. Real inking and brush lettering get their taper from hand pressure: light at the start, firm in the middle, easing off at the exit. If you use an Apple Pencil, a brush with generous pressure response and Classic Taper off may give you more convincing line variation than a heavily configured taper. For flicked strokes like hair, grass, or whip-fast calligraphy, a short end taper plus a quick, confident stroke usually looks better than a long programmed one.
Quick troubleshooting checklist
- Editing a duplicate of the brush?
- Adjusting Pressure Taper for Pencil and Touch Taper for fingers?
- Classic Taper off?
- Link Tip Sizes on, with the end node actually moved inward?
- Size raised high enough to see a change?
- Apple Pencil Size under Pressure set high enough?
- StreamLine low enough that it isn't smoothing out the exit?
Run through that list in order and the end of your stroke should be much more likely to taper. From there, fine-tune Tip and Pressure until the line matches the feel you want, then save the brush into your own set so it's ready for the next project.