How to Make Procreate Brush Smoother
StyleFrame Team6 min read
To make a Procreate brush smoother, open the brush in Brush Studio, go to the Stabilization tab, and raise StreamLine Amount first, then Stabilization Amount if the line still wobbles. If the stroke looks bumpy rather than shaky, lower Spacing so the brush stamps merge into one continuous line. Then check Jitter, Taper, and your Apple Pencil pressure curve, and keep global stabilization low so it doesn't make every brush feel laggy.
Start with StreamLine and Stabilization
Both controls live in the brush's Stabilization tab, and they do different jobs.
- StreamLine corrects wobble and shake as you draw. Its Amount slider sets how strongly the line is evened out, and its Pressure slider changes how gradually pressure builds along the stroke. It is particularly important for inking and calligraphy-style lines.
- Stabilization averages the motion of your stroke, so higher values give more deliberate, straighter lines. It's the better tool for long, sweeping curves, where small hand tremors accumulate into visible kinks.
How to adjust them
- Open the Brush Library and tap a brush to select it.
- Tap the same brush again to open Brush Studio.
- Choose Stabilization in the left-hand list.
- Raise StreamLine Amount, then test on the Drawing Pad preview.
- Add Stabilization Amount only if the line still drifts.
Some illustrators set StreamLine somewhere between 70% and 100% for inking. Treat that as a starting point, not a rule. If you push too far, lines look mechanical and lag behind the pencil, so stop as soon as the preview stroke looks clean.
Duplicate the brush before editing. Swipe left on the brush and tap Duplicate. If you overshoot, the About this Brush tab has a Reset Brush option that restores the factory settings.
Understand global versus brush stabilization
Procreate applies smoothing at two levels, and mixing them up is a common reason a brush feels wrong.
Brush-level stabilization changes only the brush you're editing. This is the right place for most adjustments, because a pencil, an inker, and a texture brush each want different behavior.
Global stabilization sits under Actions (wrench icon) > Prefs > Pressure & Smoothing. It applies on top of every brush, including ones not built to be smoothed. A modest value around 10–15% is a sensible place to experiment. If your Pencil suddenly feels sluggish or unresponsive, check this slider first. It's easy to leave raised after a clean-line session and then wonder why your sketching brush feels dead.
A practical habit is to keep global stabilization near zero and build smoothing into dedicated inking brushes instead.
Fix bumpy edges with Spacing, Jitter, and Taper
Not every rough line is a shaky-hand problem. Procreate builds a stroke by stamping the brush shape repeatedly along your path. If the edge looks scalloped or beaded, no amount of stabilization will fix it, because the cause is in the stroke properties.
Spacing
Spacing controls how often the shape is stamped. With generous spacing, you see individual stamps with gaps between them. Reduce it toward zero and the stamps overlap into one fluid stroke. For clean ink lines, low spacing is usually the answer.
Jitter
Spacing Jitter, Jitter Lateral, and Jitter Linear add randomness to stamp placement. Lateral jitter pushes stamps sideways relative to your stroke direction, and linear jitter pushes them along it, so strokes can overshoot their start and end points. These are great for chalk or charcoal and bad for smooth line work. If a brush you downloaded looks ragged, check these values first and set them to zero or near it.
There's a quirk worth knowing: when Spacing Jitter is high, you can still see spacing variation even with base Spacing at 0%, because a minimum spacing value applies.
Taper
The Taper tab controls how the line thins at the start and end of a stroke. Pressure taper makes line ends feel confident rather than blunt, which reads as polish even when the line body is unchanged. Move the taper points to lengthen or shorten each end, and preview it before you commit.
Rendering and shape
If edges still look crunchy, a grainy or heavily randomized brush shape can mimic roughness that looks like a smoothing failure.
Tune the Apple Pencil pressure curve
Smoothness depends on how pressure translates into line width and opacity. A jumpy pressure response makes lines swell and shrink unevenly even when the path is perfect.
Go to Actions > Prefs > Pressure & Smoothing and open the pressure curve editor. If you press hard by habit, flatten or shift the curve so you aren't constantly hitting maximum width. If your lines vary too much from light touches, raise the curve's low end for more consistent output.
Pressure and tilt can also drive jitter values, so if a smooth brush suddenly behaves erratically, check whether pressure is mapped to something you didn't intend.
Improve your technique and canvas setup
Software settings can only do so much. A few habits make a visible difference:
- Zoom in for detail, zoom out for curves. Long confident curves are easier to draw at a smaller view, and short precise corrections are easier up close.
- Draw from the shoulder. Quick, continuous strokes tend to look cleaner than slow, careful ones. Slow strokes expose every tremor.
- Work at adequate canvas size. A low-resolution canvas shows stair-stepping on diagonal edges. Create the canvas at the resolution you'll deliver, or higher.
- Watch performance. A heavy file with many layers can introduce lag, which feels like jagged lines. If strokes feel late or chunky, merge layers, reduce canvas size, or close other apps before blaming the brush.
Know when smooth is the wrong choice
Heavy smoothing flattens character. Turn stabilization down or off when you need gesture energy, deliberate texture such as fur or frayed edges, sharp corners, or technical precision where the line should go exactly where you put it. Cleanup is also a different task from sketching, so keep separate brushes: a loose sketching brush with zero stabilization and a refined inker with high StreamLine.
Starting points to test
These are experiments to adapt, not fixed rules:
Where smooth Procreate lines meet a motion pipeline
Many motion designers and animators use Procreate for storyboards, character keyframes, and hand-drawn style frames before anything reaches After Effects. Line quality matters more in that context, because inconsistent smoothing from one frame to the next shows up as shimmer or "boil" once frames play in sequence. Lock your brush settings, duplicate a dedicated production brush, and use it for the whole sequence, so every drawing shares the same stabilization, taper, and spacing.
Quick troubleshooting checklist
- Line wobbles: raise StreamLine Amount.
- Line drifts or kinks on long curves: add Stabilization Amount.
- Edge looks beaded or scalloped: lower Spacing.
- Edge looks ragged or scattered: reduce Jitter values.
- Pencil feels laggy: lower global stabilization, then check file size and layer count.
- Width changes unpredictably: adjust the pressure curve.
- Brush broke after edits: use Reset Brush, or return to your duplicate.
Change one setting at a time and test on the Drawing Pad. Most "unsmooth" brushes turn out to have a single culprit, and once you know which control owns which symptom, tuning takes a couple of minutes.