How to Make Procreate Brush Not Pixelated
StyleFrame Team7 min read
Procreate brush strokes look pixelated mainly because the canvas doesn't have enough pixels, you're zoomed past 100%, or a layer has been scaled up after drawing. Start with a larger canvas (about 3000 × 3000 px or more for line art), then draw with a brush whose spacing, streamline, and shape source are set for clean edges. Avoid scaling raster strokes after the fact, and export as PNG or PSD instead of JPEG.
Why Procreate brush strokes look pixelated
Procreate is a raster app. Every stroke is a grid of pixels with anti-aliased edges, and zooming in far enough will always show them. The goal isn't to eliminate pixels but to make sure they're invisible at the size and zoom where the artwork is actually viewed.
Pixelation usually comes from one of five causes:
- The canvas pixel dimensions are too small for the intended output.
- You're viewing the canvas above 100% zoom and mistaking that for a quality problem.
- A layer was resized or rotated with Nearest Neighbor interpolation.
- The brush itself is the problem: low-resolution shape source, wide spacing, or heavy stroke smoothing.
- The export format or settings degrade the image.
Diagnose in that order. Brush tweaks rarely fix a canvas that's too small.
Fix 1: Increase the canvas pixel dimensions
DPI is a print metadata setting. It doesn't add pixels. A 1704 × 1900 px canvas is the same canvas at 72 DPI or 1200 DPI; only its nominal print size changes. What matters is the total pixel count.
For comparison:
- 10 × 10 in at 300 DPI = 3000 × 3000 px, a sensible minimum for crisp line art.
- 5 × 5 in at 300 DPI = 1500 × 1500 px, fine for social posts but soft on a poster.
- A 3 × 3 in canvas at 132 DPI is only about 400 px per side. Strokes will look rough immediately.
If you're drawing for motion work, think in video terms. A 3840 × 2160 canvas is 1:1 with UHD. If you plan to push in, pan, or scale the art in After Effects, draw at 1.5× to 2× your comp resolution so you have headroom. A 2× canvas of a UHD comp is 7680 × 4320, so check what your iPad can handle, and expect a reduced layer count.
That layer count is the real tradeoff. Procreate lowers the maximum number of layers as canvas size increases, and the limit depends on your iPad's memory. Plan your layer structure before you start: merge finished line work, keep rough construction on one layer, and put the final inking on a clean layer.
Fix 2: Check your zoom level
Many "pixelated" complaints turn out to be zoom. Anything past 100% shows individual pixels, and Procreate allows deep zoom. A common trap is a screen-sized canvas that's already stretched beyond 100% when it fills the display.
Add the Actual Size command to your QuickMenu and use it to compare. Judge sharpness at 100%, or at the size where the final piece will be seen. A line that looks stair-stepped at 400% may be perfectly clean at delivery size.
Also be aware that crisp aliased edges and soft anti-aliased edges are different looks. If you moved from an app that renders softer strokes, Procreate may feel harsher at high zoom even when the output is the same.
Fix 3: Stop scaling raster strokes
Scaling up a layer can't create detail that isn't there. Each resize, rotation, or warp resamples pixels, and repeated transforms soften or jag the edges.
Three habits help:
- Change interpolation. In the Transform (arrow) tool, check the bottom toolbar. If Interpolation is set to Nearest Neighbor, switch to Bilinear or Bicubic for smoother edges. Keep Nearest Neighbor only when you want hard pixel edges, such as pixel art.
- Transform on a draft layer. Work out composition and proportions on a rough layer, lower its opacity, then ink the final lines on a fresh layer you won't transform again.
- Decide the size first. Resizing a drawing after the fact is the most common cause of mushy lines. If a piece needs to be larger, redraw or retrace at the new size.
Fix 4: Adjust the brush itself
If the canvas is large and you're at 100% zoom but strokes still look rough, the brush is the next suspect. Open Brush Studio (tap the brush in the library) and check these:
- Stroke path spacing. If spacing is too wide, the brush stamps look like a string of beads, and edges can look jagged or lumpy. Lower the spacing for smooth, continuous lines.
- Streamline and stabilization. Higher streamline smooths wobble, but extremes can distort curves and flatten detail. Adjust in small steps and test on fast and slow strokes.
- Shape source resolution. Some imported brushes may use a low-resolution shape image. If the brush shape is small or blurry, every stamp inherits that softness, and it's more visible when the brush is scaled up. Check the shape in the Shape tab and replace it with a higher-resolution source if you made the brush yourself.
- Brush size relative to canvas. A brush set to maximum size on a small canvas can look coarse, since the shape is stretched. On a large canvas, the same preset may look different at the same relative size, so retest.
- Texture and grain settings. Grain can read as pixelation. For clean edges, reduce grain or use a brush without it. Studio Pen and Technical Pen are typical choices for crisp outlines. Textured brushes are meant to look rough.
Duplicate the brush before editing so you can always go back to the default. If every brush looks pixelated on a new canvas, the problem isn't the brush. Go back to canvas size, zoom, and resizing.
Two things to avoid: applying Gaussian Blur to hide pixel edges (it softens everything and can't recover sharpness) and relying on extremely high streamline to smooth jaggies. Both trade one problem for another.
Fix 5: Export without losing quality
Export format can undo your good work:
- PNG preserves line art and transparency without lossy compression.
- PSD keeps layers for compositing, which is what you want when the artwork is going into After Effects or Photoshop.
- JPEG compresses and can blur fine detail and add artifacts around edges. Use it only for quick previews.
After exporting, check at 100% in a viewer rather than judging from the thumbnail.
Getting Procreate art through a motion pipeline cleanly
Pixelation often reappears after export, when the art meets a composition. These checks catch most of it:
- Import at native size. Drop the PNG or PSD into a comp whose resolution is equal to or smaller than the file. If the layer scales above 100%, the software is upsampling and the edges soften.
- Keep a high-resolution source for animated scale. That way you never need to enlarge more than a small amount.
- Test early. Export one frame at the final comp scale and compare it with the Procreate original before building the whole animation.
The same applies in Cinema 4D, Blender, and Nuke when the art is used as a texture or plate: provide enough source pixels for the largest on-screen magnification, not just the default view.
Quick checklist
- Check pixel dimensions, not DPI: aim for 3000 × 3000 px or larger for line art, and 1.5–2× your comp size for motion.
- Judge sharpness at 100% using Actual Size.
- Avoid scaling raster layers up; if you must transform, use Bilinear or Bicubic interpolation.
- Lower spacing, tune streamline, and check the shape source of imported brushes.
- Export PNG or PSD, not JPEG.
- In your compositing software, import at native size and avoid scaling the art up.
- If the source is already too small, redraw at the proper size.
Following these steps in order solves most pixelation problems, because the cause is usually pixel count or scaling rather than the brush.