How to Make Procreate Brush Chisel Point
StyleFrame Team7 min read
To make a chisel-point brush in Procreate, duplicate a hard-edged brush, open Brush Studio, and replace its Shape source with a flat rectangle. Then set Spacing very low, set Rotation to a fixed angle (or to Follow Stroke for a marker feel), and reduce Taper so the tip stays blunt. The flat shape and the rotation setting together produce the thick-and-thin line variation that defines a chisel nib.
What Makes a Chisel Point Different
A round brush draws the same width in every direction. A chisel tip is a flat, angled edge, so line width depends on the angle between the stroke and the edge. Drag across the flat side and you get a wide line. Drag along the edge and you get a thin one.
To rebuild that in Procreate, you need three things to work together:
- A flat, elongated shape source, so the stamp has a broad side and a narrow side.
- A controlled rotation, so the stamp angle is either fixed (calligraphy) or tied to stroke direction (marker).
- Tight spacing and minimal tapering, so the stamps merge into a clean, hard-edged stroke instead of a pointed or scalloped one.
Everything else, such as pressure response and texture, is refinement.
Step-by-Step: Build a Chisel Brush in Brush Studio
1. Duplicate a base brush
Don't edit a stock brush directly. In the brush panel, swipe left on a hard-edged brush and tap Duplicate. Tap the copy to open Brush Studio. Rename it under About This Brush so you can find it later.
2. Replace the shape source
Open the Shape section and tap Edit to reach the Shape Source editor. You have two options:
- Draw your own. Clear the canvas and paint a solid, narrow rectangle in the center.
- Import a base. Use the Source Library to pick a base shape with a flat bar. You can also start with a square and squash it, but a drawn rectangle gives you more control over the aspect ratio.
The ratio matters. A thin sliver gives a sharp calligraphic contrast. A chunkier rectangle behaves more like a broad marker. Start around 4:1 and adjust by eye.
Keep the edges crisp. If your shape source has soft, feathered edges, the stroke will look airbrushed rather than chiseled. Tap Done when you're happy.
3. Set the stroke path
Go to Stroke Path and drop Spacing to its lowest practical value, around 1 to 3 percent. This makes each stamp overlap the next so the stroke reads as one continuous shape. Higher spacing leaves a visible chain of rectangles along the path.
Next, set Jitter (lateral and linear) to zero. Jitter is useful for texture brushes, but it breaks the clean edge a chisel needs. Leave Fall Off off unless you want strokes that fade out.
Add some StreamLine under Stabilization, a moderate amount if you're doing lettering or inking. Smoothing helps with long, flowing strokes, though too much will make the line lag behind your pencil.
4. Control the angle
This is the step that makes the brush a chisel. In Shape, you have a few options:
- Fixed angle. Drag the Rotation slider to a specific value, then test it. Angles in the 30 to 45 degree range are a common starting point for broad-edge calligraphy. Every stamp is rotated the same amount, so line width changes depending on the direction you draw, much like a physical pen held at a constant angle.
- Follow Stroke. Drag Rotation all the way to the right until the label changes to Follow Stroke. The stamp rotates to match your stroke direction. With a flat shape, this keeps the wide side perpendicular to the path, so line width stays consistent in every direction, like a felt marker that rotates as you draw. You may need to rotate the shape source by 90 degrees (two-finger drag in the source editor) so the broad side faces the right way.
Pick one of these and test it. Change one thing at a time.
5. Tame the taper
Tapering is what turns round brushes into pointed ones, so it works against a chisel. Open Taper, and for both Pressure Taper and Touch Taper, set the tip sizes to 100 percent and reduce the taper amount to near zero. Using Link Tip Sizes keeps both ends consistent. If you do want a hint of softness at the stroke ends, add only a small taper.
6. Tune pressure and size
Under Apple Pencil settings, decide how much pressure should change size. For a true chisel, keep the pressure-to-size curve mild so the width comes from stroke angle, not force. You can still link pressure to opacity for expressive shading. Under Properties, check the Maximum and Minimum size limits so you can scale from fine detail to wide blocking without distortion.
7. Test with stress strokes
Open the Drawing Pad and draw a set of tests: horizontals, verticals, diagonals, circles, and a few quick zigzags. Watch for:
- Line width changing the way you expect as you change direction.
- Clean, flat ends at the start and finish of each stroke.
- No gaps or scalloping along slow curves.
Adjust Rotation, Spacing, or the shape ratio until the tests look right.
Two Useful Chisel Variations
Calligraphy nib. Fixed rotation near 40 degrees, a thin rectangle, no taper, moderate StreamLine. Pressure affects size slightly or not at all.
Design marker. Rotation set to Follow Stroke, a medium-thickness rectangle, Opacity pressure off, and a slight opacity buildup if you want marker-style layering. This matches how a rotating-tip marker behaves.
Save each variation as its own duplicate so you can switch between them without re-editing.
Troubleshooting Common Problems
- Stroke looks scalloped or beaded. Spacing is too high. Reduce it.
- Edges look soft or blurry. Your shape source has feathered edges, or the brush has grain or wet-mix settings applied. Redraw the shape with a hard brush and disable Grain and Wet Mix.
- Brush is thin in one direction and unusable. That's normal for a fixed-angle chisel. If you want consistent width, switch to Follow Stroke or rotate the source 90 degrees.
- Angle is off by 90 degrees. Rotate the shape source in the editor with a two-finger drag instead of fighting the Rotation slider.
- Ends look pointed. Taper is still active. Set tip sizes to 100 percent and reduce taper amounts.
- Brush feels laggy. Lower StreamLine amount, or reduce the max brush size if you're working on a very large canvas.
Using Chisel Strokes in a Motion Pipeline
Chisel strokes are handy beyond illustration. Motion designers use them for hand-lettered titles, painted mattes, wipe shapes, and style frames that set the look of a sequence before animation starts. Procreate can export layered files that you can bring into compositing software. Keeping each stroke group on its own layer makes it easier to animate reveals or build mattes later.
This is also where a tool like Styleframe (styleframe.ai) can be useful. If you've drawn a handful of chisel-brush style frames in Procreate, you can use them as reference images rather than describing the look in words, so the hand-drawn character of your brushwork can carry into moving images. Your painted style frames stay the creative source, and your compositing stays where it already lives.
Quick Checklist
- Duplicate a hard-edged brush before editing.
- Draw or import a flat rectangular shape source with crisp edges.
- Set Spacing to the 1 to 3 percent range and zero out Jitter.
- Choose a fixed Rotation or Follow Stroke for angle control.
- Reduce Taper to keep the tip blunt.
- Keep pressure-to-size mild so width comes from angle.
- Test across all stroke directions and save variations separately.
Once you understand that a chisel point comes from a flat shape plus controlled rotation, you can build any variation you need, from formal calligraphy nibs to loose marker blocking, in a few minutes.