How to Make Procreate Brush Bigger When You Press Harder
StyleFrame Team8 min read
To make a Procreate brush get bigger as you press harder, open the brush in Brush Studio, go to the Pencil tab, and raise the Size slider under Apple Pencil Pressure (around 70% is a good starting point). Then test the stroke and adjust until light pressure gives a thin line and firm pressure gives a thick one. If it still feels wrong, reset the brush to its defaults, check the Maximum size under Properties, and review the global Pressure Curve in Actions → Prefs.
Step-by-step: add size pressure to any brush
Procreate lets you add pressure-driven size to any brush, including ones that don't respond to pressure out of the box, such as the default Round Brush.
- Open the Brush Library and find the brush you want to change.
- Swipe left on it and tap Duplicate. Editing a copy keeps the original intact, so you can always get back to a known-good brush.
- Tap the duplicate to open Brush Studio.
- Open the Pencil tab.
- Under Apple Pencil Pressure, find the Size slider at the top.
- Drag it to roughly 70%, then draw a few test strokes, pressing lightly and then firmly.
- Adjust the slider up or down until the range feels right, then tap Done.
This one slider is the answer for most people. A brush that looks stuck at a single width may simply not have size pressure set up yet.
Why the slider seems to do nothing
A common mix-up is that the setting appears to change only the ends of a stroke instead of the whole line. That's usually a different control: Taper. Taper shapes the start and end of a stroke, thinning it as you begin or lift off. Pressure size responds to how hard you press along the whole stroke. If your lines only get thinner at the tail, you're probably in the Taper settings, not Apple Pencil Pressure.
A second cause is a brush with leftover settings from earlier experiments. If changing the Size slider isn't producing a pressure response, reset the brush to its default settings, then change only the Size slider and test again. Changing one variable at a time makes it obvious which control does what. In one forum case, a user who thought the setting was broken got it working after resetting the brush and repeating the single change.
Also test with a deliberate range of pressures. Many people press lightly and consistently, so the stroke never visibly changes. Draw one stroke that starts as light as you can and ramps up to a hard press. If the width changes smoothly, the brush is configured correctly.
Control how large the brush can get
Pressure scales size within a range, and that range is set by the brush's size limits, not just the pressure slider. If a brush stays small even at full pressure, the ceiling may be too low.
In Brush Studio, open Properties and look under Brush behavior. There you can set the Maximum size (and a minimum size) for the brush. Drag the maximum up if you want heavier strokes at the top of the range. Drag it down if you want finer control: with a low maximum, the on-canvas size slider covers a much narrower span, which makes small adjustments easier. One forum user suggests building a dedicated fine-detail brush with a maximum around 15% for exactly this reason.
Canvas size matters here too. The same brush size percentage looks different on a 1,000 px canvas than on a 3,000 px canvas, and textured brushes show their grain differently. On a large, high-resolution canvas, a brush can feel too small even at 100%. Raising the maximum size on a duplicated brush fixes that. If the texture also looks off at the new scale, adjust the grain size in the same brush so the texture matches the larger strokes.
A practical combination for pressure-driven size:
- Pressure Size around 60–80% for a clear, readable response.
- Maximum size raised only as far as your canvas needs.
- Minimum size kept low enough that a feather-light touch still produces a thin line.
Tune pressure globally with the Pressure Curve
If every brush feels too stiff or too sensitive, the problem is probably not any one brush. Procreate has a global Pressure Curve in Actions → Prefs, where you can tweak how Pencil pressure is interpreted.
Try adjusting the curve to suit your hand, since a gentle touch and a heavy hand may each prefer a different setting.
Adjust the global curve first, then fine-tune individual brushes. If you change per-brush values to compensate for a bad global curve, every new brush you install will feel off. Setting the curve once and leaving it alone keeps behavior consistent.
Troubleshooting checklist
If size still won't respond to pressure, work through these in order:
- Check your stylus. Pressure sensitivity depends on hardware that reports pressure to the iPad. An Apple Pencil works. Some third-party styluses may not report pressure in the same way, and in that case size may not change no matter how you set the sliders.
- Check the brush. Some brushes are designed with fixed width. Duplicate it and add size pressure as described above, or pick a brush that already has it.
- Look for conflicting tilt settings. Tilt can also change size. Combined with pressure, it may produce strokes that seem inconsistent. Test with tilt-related values reduced to see what pressure alone does.
- Check Brush scaling. Under Actions → Prefs, Brush scaling controls whether size is relative to the canvas or to the screen. If brushes behave unexpectedly as you zoom, try setting it to relative to canvas, since many brushes are built for that mode.
- Turn on the Brush cursor. Enabling it in Prefs shows the outline of the brush shape when you touch the canvas, so you can see the size you're about to make before committing a stroke.
- Reset and retest. Start from the brush's default settings and change only the size pressure value.
Fine-tuning size without the slider fighting you
Pressure size is only useful if you can also set the base size accurately. Procreate's size slider is coarse at the low end, but there's a trick: while dragging the slider, move your finger away from the track. The further you move away, the slower the value changes, which lets you land on an exact number. Combine that with a lower maximum size on detail brushes and you get very precise control.
Where this fits in a motion and VFX workflow
Many readers of this article may not be illustrators by trade. If you're a motion designer, animator, or VFX artist, you probably use Procreate for the stages around your main compositing work: boards, style frames, hand-drawn texture, paint-over passes, or rough character poses. Pressure-sensitive size is what makes those marks feel hand-drawn rather than mechanical, so it's worth getting right once and saving as a duplicate brush.
A few habits help when Procreate feeds a larger pipeline:
- Keep a small set of tuned brushes (one for linework, one for fills, one for texture) rather than editing the defaults every project.
- Work at the final aspect ratio and a resolution that matches your timeline, so the brush behaves the same as it will at delivery size.
- Export flattened PNGs or layered files and bring them into After Effects or Nuke as plates, mattes, or texture elements.
This is also where Styleframe can fit, without replacing anything you've drawn. You can take a hand-drawn frame from Procreate and use it as a reference for motion work. Your pressure-sensitive brushwork stays what defines the look, and the motion work happens downstream in the tools you already use.
Quick reference
FAQ
Can I make any Procreate brush get bigger with pressure? Yes. Open the brush in Brush Studio, go to the Pencil tab, and raise the Size value under Apple Pencil Pressure. Duplicate the brush first so the original stays untouched.
Why does pressure only thin the end of my stroke? You're likely adjusting Taper, which shapes the start and end of a stroke. Use the Size slider under Apple Pencil Pressure for pressure along the full stroke.
Why won't my brush get large enough even at full pressure? Check the Maximum size in Properties, and consider your canvas resolution. Large canvases make the same percentage look smaller.
Does this work with a finger or any stylus? It depends on the hardware reporting pressure, as an Apple Pencil does. Without pressure data, the size can't change with force.