How to Make Photo as a Brush in Procreate
StyleFrame Team7 min read
To make a photo into a Procreate brush, convert it to a square grayscale image, then import it as the Shape Source (for a stamp) or the Grain Source (for a texture) in Brush Studio. Procreate reads white as opaque paint, black as transparent, and grays as partial opacity, so invert the image if your subject is dark. For a stamp, raise Spacing in the Stroke tab and turn on Orient to Screen. Procreate brush sources are grayscale only, so the photo gives you shape and texture, not its original colors.
How Procreate Treats a Photo as a Brush Source
Every Procreate brush combines two inputs: a Shape, which is the mark the brush makes, and a Grain, which is the texture that shows through that mark. A photo can fill either slot, and which one you pick decides the behavior:
- Shape Source: the photo becomes the stamp. Each dab of the brush paints the photo's silhouette and tonal structure. Use this for leaves, splatters, smoke, bokeh, or a scanned ink blot.
- Grain Source: the photo becomes a texture revealed inside strokes. Use this for paper, concrete, fabric, film dust, or canvas.
Both slots work the same way: luminance becomes opacity. White paints fully, black paints nothing, and gray values land in between. Everything below follows from that rule.
Step 1: Prepare the Photo Before Import
Most failed imports come from skipping prep. Do this in any photo editor, or in Procreate itself.
- Crop to a square. Procreate wants square sources. The maximum brush resolution is 2048 × 2048 px. Larger squares are downscaled automatically, so there's no need to go bigger.
- Isolate the subject if you want a clean stamp. If the background is busy, the brush will stamp the whole rectangle of tones. Cut out the subject first, or shoot against a plain backdrop.
- Convert to grayscale. You'll get predictable results if you see the tonal values yourself rather than leaving Procreate to flatten color.
- Push contrast with Levels or Curves. Photos are usually too mid-gray to make a convincing stamp. Crush the blacks and lift the whites so the shape reads clearly.
- Decide which way your tones go. For a stamp, the subject should be light on a dark background. If it's the other way around, you can invert inside Procreate later.
Format matters. Save as JPG with a solid background for the least trouble. A PNG with a transparent background can import as a blank square, especially if your subject is dark, because transparent areas and black areas both read as "nothing." If you use a PNG, make the subject white, or place it on a solid white or black background.
Step 2: Build a Stamp Brush From the Photo
- Open the Brush Library and tap + to create a new brush. Brush Studio opens.
- Go to the Source tab. You'll see two square slots: Shape and Grain.
- Under Shape Source, tap Edit, then Import. Choose Insert Photo to pull from your camera roll, or copy the image and use Paste. You can also press and hold the Shape square to paste directly.
- Check the preview. If your subject appears dark on light, invert it with the Invert button or a two-finger tap on the image.
- Set a neutral Grain Source. A plain option such as Blank from the Pro Library keeps the grain from interfering. Make sure the preview still shows your shape clearly.
- Go to the General tab and enable Orient to Screen so the stamp stays upright instead of rotating with your stroke direction. Turn on Stamp Preview if you want the preview window to show a single dab rather than a line.
- Still in General, set Size Limits. A generous maximum and a modest minimum let you scale the stamp from a small accent to a big hero element.
- Open the Stroke tab and drag Spacing to the right. Without this step, the images overlap and smear into a continuous line. With high spacing, each tap lands as a distinct stamp.
- Tap Done, then test on a blank canvas at different sizes and pressures.
Name the brush under About this brush so you can find it later.
A Faster Method: Duplicate a Stamp Brush
Procreate already ships with stamp brushes. Swipe left on one and choose Duplicate, open it, and replace only the Shape Source with your photo. The spacing and orientation settings carry over, so you skip the setup.
Step 3: Use the Photo as a Grain Texture
If you want the photo's texture inside normal strokes, import it as the Grain instead:
- Create or duplicate a standard drawing brush, such as a pencil or charcoal.
- In Source, tap Edit next to Grain Source and import your photo.
- If the texture has visible edges or tiling seams, use Auto Repeat, which blends the image into itself so the grain tiles seamlessly across a long stroke.
- Adjust the Grain settings and test. Photos of paper, plaster, or fabric usually work best when slightly blurred and contrast-adjusted.
Settings That Change How the Brush Feels
Once the photo is in, a few other parameters turn a flat stamp into something that feels hand-made:
- Spacing tuned down slightly: if you want a textured line instead of a pure stamp, lower spacing and see how the photo shape repeats along the stroke. Many stamp sources also make good line brushes.
- Color dynamics: since the source is grayscale, hue and saturation variation is how you reintroduce color. Adding hue jitter makes foliage or confetti stamps look varied.
Troubleshooting Common Problems
The Shape or Grain stays blank. The most likely cause is a transparent PNG with a dark subject. Resave as a JPG on a solid background, or recolor the subject white.
The brush paints a solid square. The photo's background is white (opaque). Invert the source, or isolate the subject on black.
The stamp rotates oddly. Turn on Orient to Screen in the General tab.
Stamps overlap into a smeared line. Increase Spacing in the Stroke tab.
Import isn't working at all. Check that the file is square, saved to Photos or copied to the clipboard, and in JPG or PNG. You can also copy your entire canvas and paste it directly as a shape or grain source. This is a quick way to iterate: draw or edit the source, paste, test, repeat.
The result looks muddy. Increase contrast on the source. Mid-gray areas become semi-transparent paint, which reads as weak.
What About Color Photos?
Procreate brushes can't hold a full-color stamp. If you need a photographic element in color, the practical workarounds are:
- Place the photo as an image layer and mask or erase it by hand.
- Use the grayscale brush as a mask shape, then clip a color photo layer to it, so the brush paints the shape and the clipped layer supplies the color.
- Paint with the brush, then apply color adjustments or gradient maps on top.
Taking Procreate Brushwork Into a Motion Pipeline
For motion designers and VFX artists, custom brushes are usually a means to an end: painted textures, hand-made elements, matte paintings, or style frames that eventually move. Procreate is good at producing the still. Turning it into footage is a separate problem.
A reasonable workflow looks like this:
- Build the look in Procreate. Use your photo-derived brushes to paint a style frame or a set of key poses, such as an ink-and-grit treatment or a textured illustration.
- Export layers or flattened frames as PNG and bring them into After Effects, Nuke, or Blender for animation, parallax, or compositing.
- Return to your compositing app and finish the shot there.
The point is control. The brush textures and reference frames you author remain the source of the look.
Quick Checklist
- Square image, up to 2048 × 2048 px
- Grayscale with strong contrast
- Subject white on black (or invert inside Brush Studio)
- JPG with a solid background, or a PNG with a white subject
- Import as Shape for stamps, Grain for textures
- Orient to Screen on, Spacing increased for stamps
- Auto Repeat for seamless grain
- Test, tweak, duplicate, repeat
Once you've made a handful, stamp brushes built from your own photos give you a personal texture library that you can reuse across stills, style frames, and animation reference.