How to Make Lines Thinner in Procreate
StyleFrame Team7 min read
Procreate paints in pixels rather than vectors, so you can't change the width of a finished line the way you would in Illustrator. The practical options are to redraw with a smaller brush size, erode the edges of existing lines by blurring and adjusting levels on a duplicate layer, or scale the artwork down. Set your brush's size range and stabilization before you start inking, so you rarely need to thin lines afterward.
Why You Can't Just Edit Line Width in Procreate
Procreate users have asked for a "line thickness slider" that works like the opacity slider, and a reply in that thread pointed out that changing line width after painting would be difficult because Procreate paints in pixels, not vectors. Once a stroke is painted, it's a cluster of colored pixels. Making it thinner means removing pixels from the edges, and doing that carelessly leaves jagged or pixelated results.
That's the reason the fixes below fall into two groups. Some work at the pixel level (erase, blur and level, scale). The others prevent the problem by controlling how the line is drawn in the first place. Pick based on whether the artwork is already finished.
Method 1: Redraw or Re-Ink With a Smaller Brush
If the drawing is a sketch or a loose inking pass, the cleanest result is often to trace it again.
- Lower the opacity of the thick line layer so it works as a guide.
- Create a new layer above it.
- Select your inking brush and drag the Size slider (left sidebar) down.
- Trace over the guide, then hide or delete the original layer.
This keeps stroke ends and curves crisp because every line is freshly rendered at the new width. It costs time, but for hero artwork or anything that will be scaled up in a composite, it's the most reliable path.
Method 2: Erode the Lines With the Eraser
When the lines are only slightly too heavy, you can shave the edges.
- Pick the Eraser tool and choose the same brush you inked with, or a hard round brush.
- Zoom in far enough that you can see individual line edges.
- Set a small size and trace along the outer edge of each stroke.
This is the "hard way" one commenter on a Procreate tip video jokes about, and it is slow. It's still useful for fixing a few problem areas, such as a single curve that came out heavier than the rest. Use Procreate's StreamLine setting on the eraser if your hand shakes at high zoom.
Method 3: Blur and Adjust to Thin All Lines at Once
If you need to thin an entire layer uniformly, a common approach is to soften the lines and then push the tonal range so the edges contract. The exact steps depend on your artwork, so work on a duplicate layer.
- Duplicate the line art layer and hide the original as a backup.
- If your lines are on a transparent layer, put a white layer underneath and merge them, so you have dark lines on a light background.
- Open Adjustments > Gaussian Blur, choose Layer, and slide a small amount. A tiny blur is enough, because the goal is to soften the edge, not smear it.
- Open Adjustments > Curves (or Color Balance/Hue, Saturation, Brightness if that suits your art) and brighten the midtones so the soft edges fall toward white. The dark core of each line remains, but narrower.
- Convert the result back into line art on a transparent layer. One approach is to set the layer blend mode to Multiply over your colors; another is to select by color and delete the background.
Results vary with line weight, anti-aliasing, and canvas resolution. Heavy blur turns thin strokes into faint gray ones, so increase gradually and compare to your backup.
Some artists describe a related shortcut: select the line color with a color-based selection, contract that selection by about a pixel, and delete the overlap. Whether you can do that cleanly depends on your Procreate version and its selection options, so test it on a copy before relying on it.
Method 4: Scale the Layer Down
Line width scales with the artwork. If the whole drawing is the problem, not individual strokes, scaling is the simplest fix.
- Select the layer and open the Transform tool (arrow icon).
- Choose Uniform and pinch to reduce the size.
- In the transform settings, set the interpolation to Bicubic or Bilinear for smoother edges.
- Accept the transform and, if needed, re-fill or extend the background.
The trade-off is that you also shrink the drawing itself. This is best when you can compensate by redrawing or reframing, or when you plan to enlarge the canvas afterward. To avoid quality loss, start projects on a high-resolution canvas so there's headroom to scale.
Method 5: Prevent Heavy Lines With Brush Settings
The best way to get thinner lines is to ink them thinner the first time. A few brush-level settings do most of the work.
Size range
Open Brush Studio (tap the brush) and look at Properties. The Maximum Size and Minimum Size values control how thick or thin the brush can go at the extremes. Lowering the maximum keeps a heavy hand from producing fat strokes.
Pressure response
Under Apple Pencil in Brush Studio, adjust Size and the Pressure Curve. A flatter curve gives you more consistent thin lines. A steeper curve leads to dramatic width changes with small pressure shifts.
Stabilization
Under Stabilization, increase StreamLine. Smoother strokes let you work with a smaller brush without the wobble that makes artists reach for heavier lines to hide it.
Separate layers for linework
Keep line art on its own layer, ideally with different layers for characters, props, and backgrounds. Thickness adjustments (whether erasing, blurring, or scaling) then only touch what you intend.
Choosing the Right Method
Thinning Procreate Lines in a Motion or VFX Pipeline
If your Procreate drawings are going into animation or compositing, there is a better option than fixing pixels in Procreate: export at high resolution with a transparent background and adjust line weight downstream, where the change is non-destructive.
- After Effects: Apply Minimax (Effect > Channel) to the layer's alpha with the Minimum operation to erode lines, or use Simple Choker or Matte Choker. Keyframe the radius if you want line weight to change over time.
- Nuke: Use Erode (filter) on the alpha, and compare its edge quality with a slight blur-then-grade approach.
- Blender: In the compositor, a Dilate/Erode node set to negative distance does the same job.
Check edge quality at 100% and at the delivery resolution. Erosion works on pixel values, so low-resolution art can look rough. Exporting from a larger canvas pays off here.
Where Styleframe Fits for Line-Based Animation
Thinning lines by hand works for a single illustration. It becomes harder when you need consistent line character across many frames or shots. Styleframe is an AI video and motion tool that can sit beside Procreate and After Effects in that situation.
Styleframe doesn't replace Procreate's brush controls; it extends hand-drawn work into motion while you keep your compositing workflow.
Common Mistakes to Avoid
- Thinning on the only copy of the layer. Always duplicate first.
- Over-blurring. Strong blur permanently softens the line's edge and may give you gray, weak strokes.
- Working on a low-resolution canvas. Fewer pixels means more visible jaggedness when you erode or scale.
- Mixing color and line art on one layer. Adjustments will then affect fills as well.
- Expecting a vector result. If you routinely need editable width, ink in a vector app and bring the result into Procreate for coloring.
Quick Summary
To make lines thinner in Procreate, choose the method that matches your situation: re-ink with a smaller brush for the cleanest result, trim with the eraser for small fixes, blur and adjust a duplicate for uniform thinning, or scale the layer down. Prevent the problem next time by reducing maximum brush size, flattening the pressure curve, and raising StreamLine. For animation and compositing, export from a large canvas and adjust line weight in After Effects, Nuke, or Blender, where erosion stays editable.