How to Make Lines Auto Straight in Procreate
StyleFrame Team7 min read
To make lines auto straight in Procreate, draw a stroke and keep your Apple Pencil or finger pressed on the screen at the end without lifting. After about half a second, Procreate snaps the stroke into a perfectly straight line (QuickLine). While still holding, touch a second finger to the screen to lock the angle to 15° increments. For shapes, the same hold gesture triggers QuickShape, which cleans up rough circles, rectangles, and triangles.
How to Draw a Straight Line with QuickLine
QuickLine is the fastest way to get a clean straight line, and it works when the Paint or Erase tool is selected.
- Select a brush and a layer.
- Draw a line in roughly the direction you want.
- Stop moving but keep the Pencil (or finger) on the glass.
- Wait for the stroke to straighten, which takes roughly half a second.
- While still holding, drag to change the line's angle and length.
- Lift to commit.
The line pivots around the point where you started, so you can sweep it around like a clock hand until it sits where you want it. If you place the start point correctly first, you rarely need to adjust anything afterward.
Snapping to 15° increments
With the line still held, touch a second finger anywhere on the canvas. The line locks to 15° steps, which makes true horizontals, verticals, and 45° diagonals easy. This is the quickest way to get precise angles for mechanical shapes, UI mockups, grid-based layouts, or storyboard frames where perspective lines need to be consistent.
If the line looks slightly off, you probably released the second finger before lifting the Pencil. Keep both in contact until you're happy with the angle.
Using QuickShape for Rectangles, Triangles, and Circles
QuickShape uses the same hold gesture. Draw a rough closed form, hold at the end, and Procreate replaces it with a cleaner version. It recognizes common shapes such as lines, rectangles, triangles, and circles, and it can also tidy a multi-segment polyline into straight edges.
Holding a second finger on the screen while the shape is previewed pushes it toward a regular form:
- A rough circle becomes a true circle rather than an ellipse.
- A triangle becomes equilateral.
- A rectangle becomes a square.
- A line snaps to 15° angles.
Editing a QuickShape after it appears
Right after the shape snaps, a notification appears at the top of the canvas. Tap it to open the Edit Shape menu. From there you can change the shape type, such as turning a circle into a square, and you'll see transformation nodes you can drag for fine adjustments.
This window is short-lived. Once you move on to another stroke, the shape is just pixels, so you'd have to use the Transform tool for further changes. If you know a shape will need tweaking, edit it immediately or put each shape on its own layer.
Making Every Stroke Straight with Drawing Guides
QuickLine straightens one stroke at a time. If you need many straight lines aligned to a system, such as a grid, use Drawing Guide with Drawing Assist.
- Set up a Drawing Guide in Procreate's canvas settings.
- Open the Layers panel, tap the layer thumbnail, and choose Drawing Assist.
Strokes on a layer with Drawing Assist snap to the guide. The layer thumbnail shows an "Assisted" label so you can tell which layers are affected. This is useful for mockups, architectural layouts, or any art where lines should follow a consistent system rather than just be straight.
Adjusting or Turning Off the Straight-Line Behavior
If QuickLine feels too fast, too slow, or you keep triggering it accidentally, you can change it:
- Tap the Actions menu (wrench icon).
- Go to Prefs, then Gesture Controls.
- Open the QuickShape settings.
- Adjust the delay, change the trigger, or disable the feature.
A longer delay is helpful if you draw slowly with hesitation at the end of strokes, such as when inking. A shorter delay speeds up diagram work. If you do mostly organic sketching, turning it off may be easier, since you can always switch it back on for technical work.
Troubleshooting: Lines Are Straight When You Don't Want Them
A common complaint is that every stroke comes out straight or locked horizontal and vertical. Work through these in order.
Check Assisted Drawing
- Go to Actions > Prefs > Gesture Controls and open the Assisted Drawing tab. If Apple Pencil is enabled there, turn it off.
- Open the Layers panel and look for "Assisted" under the layer name. If it's there, tap the layer and toggle Drawing Assist off.
A layer with Drawing Assist and an active Drawing Guide will force strokes onto guide lines, which looks a lot like unwanted straightening.
Look for a QuickShape notification
If you do get the shape notification at the top of the canvas, QuickShape is firing. Lengthen the delay or turn it off in Gesture Controls. If you don't see the notification and strokes are still stiff or straight, the cause is something else, most likely stabilization.
Reset stabilization and smoothing
Heavy stabilization can make strokes look like they're being pulled into straight lines. Check:
- The brush itself. Open the brush settings and look at its Stabilization values. Test a few default brushes to see whether the problem follows the brush or the app.
- App-wide smoothing. Go to Actions > Prefs > Pressure and Smoothing and tap Reset to return the values to defaults.
Users have reported cases after app updates where drawing behaved as if stabilization were maxed out, even though sliders looked normal. Resetting Pressure and Smoothing is a commonly suggested fix. If it persists, restart the app or device and test with your finger instead of the Pencil to isolate the cause. Recording a short screen capture of the behavior also helps if you contact support.
Practical Tips for Cleaner Straight Lines
- Start with placement. QuickLine pivots around the start point, so put it exactly where the line should begin.
- Draw long strokes in one pass. Longer lines are easier to rotate into position than short ones.
- Use a consistent brush. Pressure-sensitive brushes can taper lines after snapping. A monoline brush (constant width) makes straight lines look uniform.
- Separate construction lines. Put guides and perspective lines on their own layer so you can lower opacity or delete them later.
- Combine tools. Use QuickShape for the base form, then Transform or Selection to scale and align it.
- Lock transparency and use Alpha Lock when you want to recolor straight lines without disturbing their edges.
Where Straight-Line Procreate Work Fits in a Motion Pipeline
Many motion designers and animators use Procreate for storyboards, style frames, and character or prop concepts before moving to After Effects, Cinema 4D, Blender, or Nuke. Clean linework helps downstream: geometric elements stay crisp, and perspective lines make layout intent clear for 3D artists and compositors.
When you export, choosing a format that preserves transparency or layers lets you bring elements into After Effects as separate pieces. Keeping straight-line elements like horizon lines, panels, and UI frames on their own layers makes them easy to animate or replace later.
Using Procreate frames as references in Styleframe
If you're exploring a look or animating between key moments, those clean frames can serve as reference inputs to , an AI video and motion tool. Crisp, deliberate linework gives reference-driven tools a clearer signal about shape and structure than loose sketching does.
None of this replaces your drawing skills or compositing tools. It extends what you can do with the frames you've already made.
Quick Reference
FAQ
Why won't my line straighten? You may be lifting too early, or QuickShape may be disabled or set to a long delay. Check Gesture Controls and make sure you're holding at the end of the stroke without moving.
Can I straighten a line after I've drawn it? Not with QuickLine, which only works while the stroke is still held. Undo and redraw it, or use Selection and Transform to rotate or scale it into place.
Do I need an Apple Pencil? No. Holding a finger on the screen works too, though the Pencil gives you more precise placement.
Why are all my lines horizontal or vertical? Most often an active Drawing Guide with Drawing Assist enabled on the layer, or the Apple Pencil option in Assisted Drawing. Turn them off and test again.