How to Make Layer Less Opaque Procreate
StyleFrame Team6 min read
To make a layer less opaque in Procreate, open the Layers panel, tap the "N" to the right of the layer name, and drag the Opacity slider to the left. A faster route is to tap the layer with two fingers and slide left on the screen; the percentage shows at the top as you drag. Both methods change the whole layer non-destructively, so you can revisit the value at any time.
Method 1: Lower opacity from the layer's "N" menu
This is the most precise method, because the slider sits next to the blend mode controls and shows a percentage.
- Tap the Layers icon (two overlapping squares) at the top right.
- Find the layer you want to fade.
- Tap the small letter to the right of the layer name. It reads "N" by default, and it changes if you've set another blend mode.
- Drag the Opacity slider left. 100% is fully visible, and 0% is invisible.
The panel is also where you change the blend mode, so you can fine-tune how a faded layer interacts with the ones beneath it. Setting a layer to 40% Multiply produces a very different result from 40% Normal, and it's worth checking both before you commit to a look.
Because the value lives on the layer rather than in the pixels, you can reopen the slider and change it as often as you like. Nothing is baked in.
Method 2: The two-finger tap
When you're mid-painting and don't want to open menus, this is quicker.
- Open the Layers panel.
- Tap the target layer with two fingers at the same time. An opacity slider appears at the top of the canvas.
- Slide left to reduce opacity or right to increase it. Your finger or the Apple Pencil both work.
- Lift off to set the value.
The interaction is gestural, so it's less exact than the slider in the "N" menu. If you need a specific value, such as exactly 35%, watch the percentage readout and nudge until it matches. For rough decisions like "a bit lighter," the gesture is hard to beat.
Method 3: Adjustments > Opacity
Procreate also has an Opacity option in the Adjustments menu. It acts on the active layer's contents.
- Select the layer.
- Tap Adjustments, then Opacity.
- Slide left or right on the canvas. The blue bar at the top reads out the current value, starting at 100%.
- Use the bottom buttons to Cancel, Undo, Redo, or Reset.
- Commit by tapping the Adjustments icon again or choosing another tool.
This works like a tool session. It's useful if you like Procreate's undo, redo, and reset controls while you experiment, but for ordinary layer fading the layer-panel sliders are more convenient and keep the value editable in the panel.
Reducing opacity on only part of a layer
Sometimes you only want to fade one area. Procreate handles this through selections, and the behavior differs from layer opacity.
- Make a selection with your preferred selection method.
- Open Layers and two-finger tap the layer holding the paint.
- Slide a finger left or right on the canvas to lower or raise the opacity of the selected area.
The important caveat is that this is destructive. When you exit the mode, the change is applied to the pixels. You can undo immediately, but you can't return later and adjust the value as you can with the layer slider. If you might want to change your mind, split the area onto its own layer first (copy and paste the selection to a new layer) and then use layer opacity on that.
Brush opacity is a different control
A common point of confusion is that "making something less opaque" can mean two things: fading an existing layer or painting with a more transparent brush. The lower slider on the Sidebar controls brush opacity. Drag it down to paint more faintly, up to paint more solidly. Brush opacity only affects new strokes. It does nothing to marks already on the canvas.
If your brush opacity is set to maximum and strokes still look too transparent, check pressure. The opacity of many Procreate brushes is affected by Apple Pencil pressure, so light strokes can produce faint marks regardless of the slider. Press harder, or look into how pressure is affecting your brush.
Why the opacity slider "isn't working"
If you drag the slider and nothing seems to change, check these common causes:
- You're on the wrong layer. Opacity applies to one layer at a time. Confirm the highlighted layer is the one you mean to change.
- The content lives on a different layer. If you painted on a clipping mask, the visible color might sit on a different layer than the one you're adjusting.
- A blend mode is masking the effect. Some blend modes can make opacity changes hard to read over certain backgrounds.
- Pressure or brush settings. As noted above, this only applies to painting, not layer fading.
Non-destructive versus destructive: a quick reference
For production work, default to the layer slider. Reserve the destructive routes for cases where you're certain.
Taking faded Procreate layers into a motion pipeline
If you're a motion designer or compositor, you're probably pulling Procreate art into a compositing or editing app rather than finishing in Procreate. A few practical notes help the handoff go smoothly.
Export layered files. Keeping your layers separate on export gives you more control in your compositor. Verify the result against your Procreate canvas, since opacity and blend mode behavior may not match one-to-one between apps.
Prefer opacity on layers over baked-in fades. If you've faded elements with the layer slider, you can re-animate them in your compositor by keyframing opacity. A Procreate fade you've baked into pixels via selection opacity can't be animated that way.
Keep a clean version. Save an unfaded copy of anything you might want to animate in. Fading in Procreate is a static decision, while fading in your compositor is a time-based one.
Mind color space. Check that the Procreate canvas profile matches your composition's working space, or semi-transparent edges and overlaps can look different after import.
Quick answers
What is the fastest way to make a layer less opaque in Procreate? Two-finger tap the layer in the Layers panel and slide left.
How do I set an exact percentage? Use the "N" menu slider and read the percentage while dragging.
Can I fade just part of a layer without losing flexibility? Move that part to its own layer first, then use layer opacity.
Does lowering opacity delete pixels? Not with layer opacity. Selection opacity and committed Adjustments changes do alter the pixels, though you can undo right after applying them.
Will my opacity values survive export to a compositing app? That can vary, so check the result against the original and confirm your blend modes.
Master those three controls, layer, selection, and brush, and you'll rarely lose time to a slider that seems to do nothing. From there, you can carry your faded layers into whichever compositing environment finishes the job.