How to Make Image Opaque in Procreate
StyleFrame Team7 min read
To make an image opaque in Procreate, open the Layers panel, tap the N beside the layer, and drag the Opacity slider to 100%. The faster route is to tap the layer with two fingers and slide right on the canvas until the readout hits 100%. If it still looks see-through, check the brush opacity, the blend mode, the parent group, and whether you are on a selection-based adjustment.
What opacity means in Procreate
Opacity controls how visible pixels are. At 100% a pixel is fully visible, and at 50% it is half see-through. Procreate lets you control opacity in three places: the brush, the layer, and a selection. Each behaves differently, and mixing them up is the main reason "make it opaque" fails.
- Brush opacity affects only new strokes you paint.
- Layer opacity affects everything on one layer and can be changed repeatedly without damaging pixels.
- Selection opacity changes pixels inside a selected area and is applied as a final action.
If you want to fix an existing image, you almost always want layer opacity. If you want future strokes to be solid, you want brush opacity.
Method 1: The layer opacity slider
This is the most reliable method, and it shows an exact percentage.
- Tap the Layers icon (two overlapping squares) at the top right.
- Find the layer holding your image.
- Tap the small letter to the right of the layer name. It reads N by default, which stands for Normal blend mode.
- Drag the Opacity slider at the top of the panel all the way to the right, to 100%.
The same panel lists blend modes, so confirm the mode is still Normal. A layer set to a different blend mode can look washed out or partly invisible even at 100% opacity, because the mode changes how it combines with what is underneath.
Because this slider can be changed as often as you like, it is non-destructive. You can set a layer to 40% for tracing, then raise it to 100% for final art without losing anything.
Method 2: The two-finger tap shortcut
When you are mid-drawing, this is quicker.
- Open the Layers panel.
- Tap the target layer with two fingers at the same time. Index and middle finger of one hand works well.
- An opacity bar appears at the top of the screen with a percentage readout.
- Slide left to reduce opacity or right to increase it. Drag until it reads 100%.
You can only adjust one layer at a time this way. The percentage readout is useful for matching values across layers. If you want two layers to sit at exactly 80%, check the number rather than eyeballing it.
Method 3: Adjustments > Opacity
The Adjustments menu also has an Opacity tool, and it works on the contents of the active layer. Tap the Adjustments icon, choose Opacity, and slide a finger left or right on the canvas. A bar at the top shows the current value, starting at 100%.
The bottom controls let you cancel, undo, redo, or reset your changes. To commit, tap the Adjustments icon again or switch to another tool. Cancel exits without applying.
This tool is useful if you prefer the Adjustments workflow, but the layer slider is better for anything you may want to revisit, because once committed, the change is applied to the layer.
Method 4: Selection opacity
Use this when only part of an image should become more or less solid.
- Open Selections and choose a method, such as Automatic.
- Make the selection.
- Open Layers and two-finger tap the layer containing the pixels.
- Slide a finger left to reduce or right to increase opacity within the selection.
Exiting this mode applies the change. You can undo right away, but you cannot keep adjusting it later like a layer slider. Treat it as a final edit. If you might want to revise it, duplicate the layer first, or put the area on its own layer and use the layer slider instead.
One caveat: raising opacity cannot restore pixels that were already erased or made transparent. If part of the image is truly missing, you need to repaint or recover it, not adjust opacity.
Method 5: Make your brush paint opaquely
If the problem is that your strokes come out thin or ghostly, the cause is on the brush, not the layer.
- Select the brush.
- Use the lower slider in the left sidebar. Drag it up to increase brush opacity and down to decrease it.
Many brushes also respond to Apple Pencil pressure. If the slider is at maximum and strokes still look faint, you may be pressing lightly or the brush's pressure settings may be mapping light touches to low opacity. Try pressing harder first. If that fixes it, adjust the brush's pressure behavior in its settings rather than fighting the slider.
Why your image still looks transparent
When the slider says 100% and the result still looks wrong, work through this checklist:
- Blend mode: Check the letter beside the layer. Anything other than N changes appearance regardless of opacity.
- Parent group: A group can have its own opacity setting. If your layer sits inside a group at 60%, the contents are limited by that.
- Clipping mask: A clipped layer only shows where the layer beneath has pixels. Partial coverage underneath looks like partial opacity.
- Layers above: A semi-transparent white or tinted layer above your image can wash it out. Hide layers one at a time to find it.
- Faint source pixels: If the original image was already semi-transparent, such as a soft-edged PNG, raising layer opacity will not make those pixels solid. Duplicate the layer and merge the copies down to build up density, or repaint the weak areas.
- Brush at low pressure: Covered above. It affects new marks only.
Making the result permanent
Layer opacity is a property of the layer. If you merge or flatten, the current opacity gets baked into the pixels. Before merging, decide whether you still need flexibility. Keeping layers separate and saving a copy of the project is cheap insurance.
For export, how you save matters:
- Exporting as a flat image captures what you see on the canvas, including any layer opacity and the background.
- If you need transparency around your artwork, hide the background before exporting, and use a format that supports transparency.
Carrying Procreate art into a motion pipeline
Many motion designers and animators use Procreate for concept art, style frames, textures, and hand-drawn elements, then move the files into other compositing and animation tools. A few habits make that handoff cleaner:
- Keep opacity decisions in layers. Keeping layer opacity intact lets you rebalance elements later without returning to the iPad.
- Separate elements deliberately. Put characters, props, and backgrounds on different layers so they can be animated independently.
- Keep fully opaque art where you need clean edges. Semi-transparent, soft pixels can show fringing when composited over different backgrounds, so check edges against a dark and a light backdrop.
- Export with a transparent background when you need a single element. Hide the background first.
If you plan to use a Procreate frame as a reference in other tools, the opacity cleanup above matters. A reference frame with a stray translucent layer, a leftover blend mode, or a half-hidden background can carry those artifacts into later work. Check the canvas against a neutral backdrop, then flatten a copy to use as your input.
Quick reference
Final tips
Use the layer slider for anything you may revisit, use selection opacity only when you are sure, and always check blend mode and group settings before assuming opacity is the problem. Once a layer is truly solid, you can export it with confidence, whether it goes into a compositing app or serves as a reference in your next project.