How to Make Flames in Procreate
StyleFrame Team6 min read
To make flames in Procreate, paint on a dark background and build the fire from deep red outward to orange, yellow, and a near-white core, then soften the transitions with Gaussian Blur and shape them with Liquify. For a faster result, the built-in Flames brush in the Elements set gives you a usable base in seconds. Finish with a glow layer set to a light-based blend mode so the fire reads as light rather than paint.
What You Need Before You Start
Flames are a lighting problem more than a drawing problem. Fire emits light, so you are painting luminance on a dark ground. Set up a few things first:
- Canvas: Work large. A canvas around 3000 px or more on the long edge gives you room to crop and scale later, especially if the flames will end up in a video timeline.
- Background: Fill the background layer with a near-black, slightly warm tone. Pure black works, but a dark brown or deep red-black makes the glow feel more natural.
- Palette: Pick five or six values ahead of time: dark red, red-orange, orange, yellow, pale yellow, and a creamy white. A fire palette is mostly about value steps, so keep the hue shifts small.
- Brushes: A soft airbrush for glow, a hard round or a gouache-style brush for shapes, and the Flames brush from the Elements set.
- Layers: Keep the background separate from every flame layer. You will need that separation later for compositing.
Method 1: Quick Flames with the Built-In Brush
Procreate's Elements brush set includes a Flames brush. It is the quickest route when you need a stylized fire for an illustration or a motion board.
- Create a new layer above the dark background.
- Pick an orange as your base color and stamp or drag the Flames brush where the fire should sit.
- Drop a second layer on top, switch to a lighter yellow, and repeat at a smaller size so the brighter flames sit inside the larger ones.
- Add a third pass in pale yellow or white at the base of each flame, where the fire is hottest.
The result is quick, but brush-generated flames can look repetitive. Vary your stroke angle, size, and pressure, and erase or smudge areas where the pattern repeats. Treat the brush as a starting point rather than a finished flame.
Method 2: Paint Flames in Layers
Painting by hand gives you the most control over silhouette and movement, which matters if the flames will drive an animation.
Step 1: Rough the silhouette
On a new layer, use a mid-red or dark orange to sketch the outer shape. Real flames are not symmetrical. Draw tongues that curve, lean, and occasionally fold back on themselves. Avoid evenly spaced, same-length spikes. Aim for one dominant lick, several secondary ones, and a few small detached wisps.
Step 2: Build color from outside in
Create a new layer for each color step, working from the darkest outer layer to the brightest inner one:
- Outer edge: deep red or red-orange, with the lowest opacity.
- Body: saturated orange.
- Inner flame: yellow.
- Core: pale yellow to white, only at the base and the thickest parts.
Each inner layer should be smaller than the one before it. Fire is brightest where it is densest, and the color falls off toward the tips.
Step 3: Soften with Gaussian Blur
Select a layer, open Adjustments, choose Gaussian Blur, and slide the Apple Pencil across the canvas to set the amount. Apply a stronger blur to the outer red layer, and a lighter one to the inner yellow layer. Differing blur amounts create the soft-to-sharp gradient that makes fire feel luminous.
If you painted every color on a single layer, you can blur that layer as a whole, which blends everything faster. You lose per-color control, though, so decide up front whether you want speed or flexibility.
Step 4: Pull the tips with Liquify
Open Adjustments, choose Liquify, and work at a modest size. Drag upward from the base of the flame to pull tips into curling points. Add small sideways pushes to suggest wind. Keep your movements slow; fast, large drags tend to smear the color into mush.
Method 3: One-Layer Gradient Flames
A popular shortcut is to paint everything on one layer as horizontal color bands, with light colors at the top and dark colors beneath, then blur and liquify the stack upward.
- Fill the canvas with bands, moving from light to dark.
- Blur the layer until the bands blend into a smooth gradient.
- Open Liquify and drag upward from the bottom with steady pressure so the colors stretch into flame shapes.
- Repeat with a smaller brush size to carve individual tongues.
This method is fast and produces a smooth look, but it is harder to edit once you have liquified. Duplicate the layer before you start so you can go back.
Add Glow, Heat, and Embers
A flame without light feels flat. Add these touches last:
- Glow layer: Create a new layer above the flames, set it to a light-based blend mode, and paint soft orange with a large airbrush around the brightest areas. Then apply a light Gaussian Blur.
- Ambient light: On a layer under the flames, paint a faint warm wash on nearby surfaces, such as a log, a wall, or a character's face. Orange light on surrounding objects sells the fire more than the flame itself.
- Embers and sparks: Use a small hard brush to place dots and short streaks drifting upward. Vary size and opacity, and keep most of them close to the fire.
- Smoke: A soft, low-opacity gray-brown brushed above the tips adds depth. Keep it subtle so it does not compete with the flame.
Common Mistakes to Avoid
- Painting on a light background: Flames lose their luminous quality when the surrounding value is too high.
- Too many hues: Stick to a tight red-to-yellow range. A touch of blue at the base is fine for gas flames, but rarely needed.
- Uniform shapes: Symmetry and repetition read as clip art. Vary height, lean, and spacing.
- Over-blurring: If every edge is soft, the flame becomes a blob. Keep a few crisp tips against the soft glow.
- Skipping surrounding light: The environment's response to the fire is half the effect.
- Flattening too early: Keep layers separate until you are sure you are done, especially if you plan to animate or composite.
Quick Recap
- Start with a dark background and a limited warm palette.
- Use the Flames brush for speed, or paint layered silhouettes for control.
- Blur each color layer by a different amount, and push the tips with Liquify.
- Add glow with a light-based blend mode, plus embers and ambient light.
With a few layered passes and a good glow, Procreate can produce flames that hold up in a standalone illustration.