How to Make Dotted Style Pen in Procreate
StyleFrame Team7 min read
To make a dotted-style pen in Procreate, duplicate the stock Monoline brush, open Brush Studio, and raise Spacing under Stroke Path until the round stamps separate into distinct dots. Set Taper to none so every dot stays the same size, then rename and save the brush. For dashes instead of dots, import a short straight line as the brush's Shape source and set its rotation to Follow Stroke.
How a dotted pen works in Procreate
A Procreate brush is a repeating stamp. Each stamp is a shape, and the Spacing value controls how far apart the stamps land along your stroke. At low spacing the stamps overlap into a continuous line. Push spacing high enough and the overlap disappears, leaving individual dots.
This means a dotted pen needs no new artwork, just a round brush with different spacing. Dashes work the same way, except the stamp is an elongated shape instead of a circle.
For motion designers this matters because the result is a raster brush, not a vector path. It is great for hand-made texture and bad for infinitely scalable line work, so plan your canvas size around where the artwork ends up (more on that below).
Method 1: Duplicate Monoline and increase spacing
This is the fastest route and gives you a clean, uniform dotted line.
- Open the Brush Library (the paintbrush icon).
- Find the free Monoline brush from the Procreate original brush collection. Swipe left on it and tap Duplicate. Always work on a copy so the original stays intact.
- Tap the duplicate to open Brush Studio.
- Go to Stroke Path. Drag Spacing to the right. Somewhere around 60 to 70% usually produces clearly separated dots, but the right number depends on how large you draw. Check the preview pad as you drag.
- Still in Stroke Path, open Taper and set the taper sizes to none. Otherwise, each stroke starts with smaller dots.
- Open Stabilization and adjust Streamline and Stabilization if you want smoother curves. Higher values help on long sweeping lines, while lower values keep tight corners from rounding off.
- Tap About this brush, rename it (for example "Dotted Pen"), and tap Done.
Test it on a blank layer at a few sizes to see how the dots look.
Method 2: Build a dotted pen from scratch
If you want a more characterful pen, such as a stippled marker with varied dot sizes, start from a new brush instead of Monoline.
- In the Brush Library, tap + to create a new brush.
- In Shape, confirm the source is a plain circle.
- In Stroke Path, set Spacing to roughly 60%.
- In Dynamics, set Size Jitter to a moderate value so dots vary slightly in diameter. Around 60% reads as obviously hand-stamped.
- In Apple Pencil, set pressure-to-opacity to none, so dots do not fade in and out with pressure. If you want a pressure-sensitive pen, keep some response on Size instead.
- Optionally, open Color Dynamics and add a small Stamp Color Jitter on Hue (5 to 10%) so each dot shifts slightly in color. Keep it low, because high values quickly turn rainbow.
- Name and save the brush.
This approach takes a few more minutes, but you control every behavior instead of inheriting Monoline's defaults.
Making a dashed pen
Dashes need a custom shape source.
- Create a square canvas. With a monoline brush at maximum size, draw one short, thick line. Press and hold at the end of the stroke to use QuickShape so the line is perfectly straight.
- Open the Layers panel, tap the layer, and choose Copy.
- Duplicate your Monoline brush and open Brush Studio.
- Go to Shape, tap Edit, then Import, then Paste. Tap Done.
- Set the shape's Rotation to Follow Stroke so the dash turns with your pen direction.
- Adjust Spacing until the gap between dashes looks right. Try 60 to 70% as a starting point.
- Save the brush under a clear name.
Draw your source line in white.
Fixing common problems
- Dots look like a bumpy line. Spacing is still too low. Keep dragging it right.
- Dots shrink at each stroke end. Taper is still active. Set it to none in Stroke Path.
- Dots fade unevenly. Pressure is controlling opacity. Open the Apple Pencil panel and reduce the pressure-to-opacity response.
- Dashes do not follow curves. Rotation is not set to Follow Stroke.
- Dashes look cropped or blurry. Your imported shape was too small or low contrast. Redraw it on a larger canvas and re-import.
- Corners look rounded. Stabilization is too high. Lower Streamline and Stabilization for sharper turns.
Settings reference
Treat these as starting points and tune by eye.
Exporting dotted artwork for motion work
Once you have a pen you like, the next question for an animator is how to get the art into a composite cleanly.
Draw large. Procreate brushes are raster. If the final comp is 4K, set up your canvas to match or exceed it, so dots do not soften when scaled. Check the canvas dimensions and DPI before you draw.
Export with transparency. Hide the background color layer, then export as PNG so the dots land in After Effects on an alpha channel. Export layers separately if you want to animate parts independently.
Consider whether you need a raster at all. If you only need a clean dotted path that draws on, a native After Effects approach is often faster. On a shape layer, add a stroke, set the line cap to round, and use the Dashes control with a dash value of 0 and a gap value, which gives you perfectly round dots. Add Trim Paths to animate the line drawing on. You keep resolution independence and exact control. The Procreate pen is the better choice when you want imperfection, such as slightly uneven dots, a hand-drawn wobble, or color variance.
Animate frame by frame if you want it hand-made. Procreate's Animation Assist lets you draw the dotted line across several frames. Export the result as a PNG sequence and import it into After Effects or Premiere Pro as an image sequence.
Where Styleframe fits
If the dotted look is a style you want across more than hand-drawn elements, such as footage, 3D renders, or generated shots, a reference-driven tool can carry it further. Styleframe is an AI video and motion tool built for artistic control, and its Restyle and Ink-and-Paint features apply the look of a reference image to a video clip. A frame of your Procreate dotted-line artwork can serve as that reference, so the result stays tied to your own drawing instead of a generic filter.
For motion that needs to travel between your keyframes, Frames-to-Video generates from start and end keyframes you supply, which suits a stylized transition between two illustrated frames. Generations are driven by your references, clips, and keyframes, and iteration is non-destructive, so you can step back to an earlier pass without losing work. Output can be upscaled to 4K, and Remove Background helps pull a subject out for compositing.
Styleframe exports image sequences, so the result drops into the same After Effects or Nuke comp as your Procreate PNGs. Your compositing, grading, and final delivery stay where they already live.
Quick workflow summary
- Duplicate Monoline, raise Spacing, set Taper to none, and save. That is your dotted pen.
- For dashes, paste a short line into the Shape editor and set rotation to Follow Stroke.
- Add Size Jitter or Stamp Color Jitter for a more hand-stamped feel.
- Draw at or above your final comp resolution and export as transparent PNG or a PNG sequence.
- Use After Effects dashes and Trim Paths when you need precise, resolution-independent dotted lines, and the Procreate pen when you want texture and imperfection.
Once the brush exists, you can reuse it on every project. Build a small set (fine dots, bold dots, short dashes, long dashes), and you will have a reusable toolkit of hand-drawn line styles to bring into your motion pipeline.