How to Make Dotted Brush in Procreate
StyleFrame Team6 min read
To make a dotted brush in Procreate, duplicate the default Monoline brush, open Brush Studio, go to Stroke Path, and raise Spacing until the dots separate, usually around 60-70%. Then set all Taper values to none so every dot stays the same size, rename the brush under About this brush, and tap Done.
Before You Start
You need Procreate on an iPad, and an Apple Pencil helps with the pressure settings. The default Monoline brush lives in the Calligraphy set. Always duplicate it before editing so the original stays intact.
To duplicate, open the Brush Library, swipe left on Monoline, and tap Duplicate. Double-tap the copy to open Brush Studio. Every setting below lives in that panel.
Method 1: A Clean Dotted Line from Monoline
This is the fastest route and produces uniform round dots, good for borders, map routes, stitching effects, and lettering accents.
- Duplicate Monoline and open the copy in Brush Studio.
- Open Stroke Path and drag Spacing to the right. At the default value the dots overlap into a solid line. Somewhere between 60% and 70% gives clear gaps. Lower values pack the dots closer, higher values spread them.
- Open Taper and set all the taper sizes to none. If you skip this, the first and last dot of every stroke shrinks, which looks like a mistake in a clean dotted line.
- Optional: Stabilization. Adjust Streamline, Stabilization, and Motion Filtering to smooth wobbly strokes to your personal preference.
- Rename the brush by tapping About this brush, then tap Done.
Test it on a blank canvas at several sizes. Dot size is controlled by the normal brush size slider, so one brush covers fine hairline dots and bold dots alike.
Method 2: A Colorful, Hand-Made Dotted Brush from Scratch
If you want dots with variation in size and color, build the brush from a blank template instead of Monoline.
- In the Brush Library, tap the + icon to create a new brush.
- Shape: the default is a basic circle, which is what you want.
- Stroke Path: set Spacing to about 60% so the dots separate.
- Dynamics: under Jitter, set Size to about 60%. Some dots will print smaller and some larger, which gives a hand-stamped look.
- Apple Pencil: under Pressure, drag Opacity all the way to the left so dots do not fade in and out with pressure.
- Color Dynamics: under Stamp Color Jitter, raise Hue to roughly 5-10%. Each dot shifts slightly in color from your selected one. Push it too high and you get a rainbow, so keep it subtle.
- Rename and tap Done.
The color you pick in the palette becomes the starting point of the hue variation, so changing swatches gives you whole families of dotted strokes from one brush.
Method 3: A Dashed Brush with a Custom Shape
Dashes need a custom shape source because the brush stamp is no longer a circle.
- Create a square canvas. Any size works as long as it is square (1080 × 1080 px is plenty).
- With a Monoline brush at maximum size, draw a short, thick line. Hold at the end of the stroke to snap it straight with QuickShape. Center it on the canvas using the Transform tool with snapping on.
- Copy the layer. Use the layer menu and tap Copy, or swipe down with three fingers and choose Copy All.
- Duplicate your dotted brush (or Monoline) and open Brush Studio.
- Go to Shape, tap Edit, then Import, then Paste. Procreate will show the line as black on white. Tap with two fingers to invert it so the shape reads as white on black, then tap Done.
- Under the new shape source, set Rotation to Follow Stroke so the dashes align with your stroke direction.
- In Stroke Path, adjust Spacing until the gaps look right.
- If dashes look misaligned or tilted, check Properties and turn off Orient to Screen.
- Rename and save.
A shorter shape gives short dashes, a longer shape gives long ones, and you can create a whole set by repeating the process with different source lines.
Settings Reference
Troubleshooting
- Dots overlap into a line: Spacing is too low. Increase it.
- First and last dots look tiny: Taper is still active. Set all taper values to none.
- Dots fade unevenly: Pressure Opacity is not zero. Drag it fully left in the Apple Pencil settings.
- Dashes rotate randomly or look tilted: Rotation is not set to Follow Stroke, or Orient to Screen is still on.
- Dots look jagged on tight curves: Increase Stabilization or draw slower. Very high spacing on tight curves will always produce uneven gaps, so lower it slightly.
- The shape looks inverted: Imported shapes need to be white on black. Invert the source in the shape editor.
Using Procreate Dotted Strokes in Motion Work
Procreate brushes are raster, so what you draw is a flat image. For motion designers, animators, and compositors, that has a few practical consequences.
Exporting Cleanly
Export from Procreate as a transparent PNG, with the background layer hidden, at a resolution at least as large as your comp. Dotted lines are made of fine detail, and scaling a small raster up in After Effects softens dot edges. Draw big, then scale down.
Hand-drawn dotted lines that wobble from frame to frame give a boiling-line look that is hard to fake procedurally.
Rebuilding the Look in Animation Software
If the dotted line needs to animate along a path, a vector approach in your animation software is usually more flexible than a Procreate raster. The Procreate brush remains the better option when you want irregular size, color jitter, or an organic imperfect feel. Many artists use both: a native dotted path for structure and a Procreate-drawn layer for texture and accents.
Quick Tips for Better Dotted Brushes
- Make a small set. Save a tight dotted brush, a loose jittery one, and a dashed one in a custom brush set so they travel together.
- Draw at large canvas sizes if the strokes will be scaled in video, since raster dots soften when enlarged.
- Use QuickShape for straight dotted lines and perfect circles.
- Test on a dark and light background. Hue jitter and soft edges can read differently against each.
- Back up your brushes. Share or export the brush set so a reinstall does not erase your work.
FAQ
What is the easiest way to make a dotted brush in Procreate? Duplicate Monoline, increase Spacing in Stroke Path, and set Taper to none.
Why are my dots touching? Spacing is too low. Raise it until the gaps appear, typically 60-70%.
Can I make dashes instead of dots? Yes. Import a thick line as the brush shape, set Rotation to Follow Stroke, and raise Spacing.
Can I animate a Procreate dotted brush in After Effects? You can import frame-by-frame exports as image sequences. For path-driven animation, a vector path is usually easier to control.