How to Make Brush Tip Sharp in Procreate
StyleFrame Team6 min read
To make a brush tip sharp in Procreate, duplicate the brush, open Brush Studio, and set the Shape source to a hard-edged tip. Then open the Taper tab, link the start and end tip sliders, and push them toward the middle or higher so the stroke narrows to a point on both ends. If you want sharp ends without pressure, reduce the size dynamics so Taper controls the line width instead of how hard you press.
What "sharp" means in Procreate
"Sharp" covers three different problems, and each has its own fix.
- A crisp tip shape: the edge of the brush stamp is soft or grainy, so the line looks fuzzy. This is a Shape setting.
- Pointed stroke ends: the line starts and finishes in a point, like an ink brush or a vector stroke with taper. This is a Taper setting.
- Consistent width with sharp ends: the line stays the same thickness in the middle and tapers only at the ends, even without pressure. This combines Taper with reduced size dynamics.
Decide which one you need before opening Brush Studio.
Before you start: duplicate the brush
Editing a default brush overwrites it, and it is easy to forget the original settings. Open the Brush Library, swipe left on the brush, and tap Duplicate. Rename the copy in the About This Brush tab, then tap the copy to open Brush Studio. Every change below applies to the duplicate.
Step 1: Give the brush a hard-edged tip shape
If the brush edge is soft, no amount of tapering will make it look sharp.
- In Brush Studio, open the Shape tab.
- Tap Edit under Shape Source.
- Choose Source Library and pick a hard shape, such as a medium-hard or hard round.
- Tap Done and test in the drawing pad.
Rough or grainy shape sources make the outline of a stroke look ragged. Swapping in a clean library shape smooths the edge right away. If you want to keep texture inside the stroke, leave the Grain settings alone and change only the Shape source.
Also check Properties. The Maximum and Minimum size limits control how thin or thick the brush can go. If your point still looks blunt at small sizes, lower the Minimum size so the brush can shrink further.
Step 2: Use Taper to create pointed ends
Open the Taper tab. It has two sections: Pressure Taper and Touch Taper. Each section has its own tip and size sliders. For sharp-ended strokes, one forum answer suggests working in Pressure Taper and ignoring Touch Taper.
For a stroke that comes to a point at both ends:
- In Pressure Taper, find the Tip controls for start and end.
- Turn on Link Tip Sizes so the start and end tapers match.
- Raise the size taper amount until the stroke narrows to a clear point. A value around 40% is a reasonable starting point, and you can go higher for longer, more dramatic points.
- Set the Size slider to 100% so the point is as sharp as the brush allows.
- Test with a quick stroke and adjust.
If you only get a sharp start or a sharp end but not both, the start and end sliders are likely unlinked or set to very different values. Link them first, then tune the amount.
Classic Taper
If the newer taper sliders seem to do nothing, check whether Classic Taper is switched on in Brush Studio. One forum answer recommends turning Classic Taper off in the General tab and then moving both Amount sliders toward the middle for maximum tapering.
Classic Taper can still be useful. A tutorial for watercolor and ink-style brushes uses it on purpose to get strokes that start thin, swell, and fade out the way a real brush does. Treat it as a style choice rather than a fix.
Step 3: Get sharp ends without relying on pressure
Many illustrators and designers need lines of the same weight with clean pointed ends, similar to a stroke profile in a vector app. That is harder in Procreate, because pressure sensitivity naturally changes line width.
A workable recipe:
- Turn down the size dynamics. If speed affects size, pull the speed-based size dynamics down as well. One experienced user suggests starting with speed at -100%.
- Go to Pressure Taper, link the start and end tip sizes, and set them to about 40%.
- Set Size to 100% and leave the other taper sliders at none, so only the tip is tapering.
- Make sure the Shape source is a hard shape.
- Ignore Touch Taper.
The result is a stroke that stays consistent through the middle and narrows to a point at each end, no matter how hard you press. If the line still swells or thins unpredictably, some other size dynamics setting may still be affecting it.
Step 4: Clean up wobble with StreamLine
Sharp ends look best when the stroke itself is smooth. In Stroke Properties, raise StreamLine to correct small wobbles in the path. Many brushes already include some. For long, confident strokes, a moderate setting plus a strong taper tends to give the cleanest result.
Troubleshooting common problems
Changing Touch Taper does nothing. This is a common point of confusion. Adjust Pressure Taper instead and ignore Touch Taper.
Only one end is sharp. Link the tip sizes, then raise the amount. Check that start and end values are not wildly different.
The point is still blunt. The Shape source is probably soft, or the Minimum size in Properties is too high. Switch to a hard shape and lower the Minimum.
The line gets thick when I press hard. Reduce the size dynamics, then rely on Taper for the pointed ends.
Save a sharp-tip brush set
Once a brush behaves the way you want, keep the setup. Duplicate it for variants: one for thin pointed linework, one with a longer taper for flourishes, and one with consistent width for technical lines. Group them in a custom brush set.
Quick checklist
- Duplicate the brush before editing.
- Shape: choose a hard source from the library.
- Properties: lower the Minimum size if the tip stays blunt.
- Taper: link tip sizes, set Size to 100%, and start the amount around 40%.
- Classic Taper: turn it off if the newer sliders seem ineffective.
- For constant width: reduce size dynamics, including speed, and ignore Touch Taper.
- StreamLine: raise it moderately to smooth the stroke.
- Save finished brushes in a custom set.
FAQ
Why won't my Procreate brush make a sharp point?
Usually the Shape source is soft or the Minimum size is too high. Set a hard shape in the Shape tab, lower the Minimum size in Properties, then raise the Pressure Taper tip amounts.
How do I taper both ends of a stroke?
In the Taper tab, turn on Link Tip Sizes under Pressure Taper and raise the tip amounts. Linking makes the start and end match.
Can I get tapered strokes without pressure sensitivity?
Yes. Reduce the size dynamics, including speed, then use Pressure Taper with linked tips and Size at 100%. The stroke will keep a consistent width and narrow only at the ends.
What should I do about Touch Taper?
For sharp-ended strokes, one forum answer advises ignoring Touch Taper and adjusting Pressure Taper.
Should I edit the default brushes?
Duplicate them first. That way you keep the original and can always compare against it.