How to Make Brush Strokes Smoother in Procreate
StyleFrame Team7 min read
Smoother Procreate strokes come from three settings in Brush Studio: raise StreamLine Amount, add a little Stabilization and Motion Filtering, and lower Spacing so the brush stamps merge into one continuous line. Apply these per brush on a duplicate so the original stays intact, and use global smoothing in Prefs only when you need it across every tool. Canvas size, zoom level, and how you move your arm matter too, because no setting fully corrects an input problem.
Why Procreate Strokes Look Rough
Procreate builds a stroke by plotting points along the path of your finger or Apple Pencil and stamping the brush shape along them. Three things can make that line look rough:
- Input wobble. Hand tremor and short, hesitant movements create small deviations in the path.
- Stamp spacing. If stamps are spaced too far apart, you see scalloped edges or visible dots instead of a fluid line.
- Randomness in the brush. Jitter, grain, and pressure response can add variation you didn't intend.
Each cause has its own fix, so diagnose first. A wobbly curve points to stabilization. A beaded or bumpy edge points to spacing. A line that thickens and thins unpredictably points to the pressure curve or size settings.
Step 1: Raise StreamLine on the Brush
StreamLine usually makes the biggest difference, especially for inking and lettering.
- Open the Brush Library and swipe left on the brush you want to change. Tap Duplicate.
- Tap the duplicate to open Brush Studio.
- Open Stabilization in the left-hand list. On a smaller iPad, scroll to the top of the list if you don't see it.
- Raise StreamLine > Amount while scribbling in the Drawing Pad on the right.
Clear the Drawing Pad first so you can see the effect in real time. Raising Amount straightens out wobbles and shakes, while lowering it gives a looser, more natural line. Make small changes, test, and stop when the line looks clean but still feels responsive.
The Pressure slider under StreamLine controls how quickly pressure kicks in. Higher values give a longer, smoother pressure build, which helps with tapering strokes in inking. Lower values make the brush respond faster as you press.
Rename the duplicate (for example, "Inker Smooth") in the About this Brush tab. If you overshoot, Reset Brush in that same tab restores the original settings.
Step 2: Add Stabilization and Motion Filtering
In the same Stabilization panel, you'll find two related controls:
- Stabilization (Amount) averages the movement of your stroke. The higher the value, the more it smooths out small deviations. It tends to produce deliberate, slightly lagging lines, which suits long curves and clean outlines.
- Motion Filtering was designed with hand tremors in mind. If your line has tiny high-frequency shakes rather than larger drifts, this is the control to try.
A practical approach is to treat them as layers. Start with StreamLine for general cleanup, then add a modest amount of Stabilization for long, sweeping curves. Use Motion Filtering only if tremor remains. Stacking all three at high values makes a brush feel mushy, with a visible delay between your pencil and the ink.
Step 3: Check Global Smoothing and the Pressure Curve
Brush-level settings only affect that brush. For a blanket adjustment, go to Actions (wrench) > Prefs > Pressure and Smoothing. There you'll find a global Stabilization slider and the Apple Pencil pressure curve.
- Global stabilization overrides or adds to brush behavior across all tools. It's useful when your hand is shaky on a particular day or you're doing a lot of clean lineart. Start low, around 10–15%, and raise it gradually.
- Pressure curve changes how Procreate interprets the force from your Apple Pencil. If strokes feel jumpy or the width swings too sharply between light and heavy, reshaping the curve can calm that response. You can reset it to default at any time.
If your pencil suddenly feels laggy or unresponsive, check global stabilization first. It's one of the most common causes, especially after you've forgotten you turned it up for a previous task.
Also note that pressure-based adjustments only show up with a pressure-sensitive stylus and a brush that has pressure sensitivity applied. If you're drawing with a finger, you won't see the effect.
Step 4: Tune Spacing, Jitter, and Fall Off
If smoothing doesn't fix a bumpy edge, the problem is likely stamp placement. Open Stroke Path in Brush Studio.
- Spacing: Lower values make stamps overlap and merge into a single fluid stroke. Higher values reveal individual stamps. For clean ink-style lines, keep Spacing low.
- Jitter (Lateral and Linear): These shift stamps sideways or along the stroke. Any value above zero introduces roughness, which is great for texture and bad for crisp outlines. Set both to zero for clean lines.
- Spacing Jitter: Even with base Spacing at 0%, high Spacing Jitter will still change stamp placement, because there's a minimum spacing value. Reduce it if you see unexpected gaps.
- Fall Off: This fades a stroke as it goes. Turn it off if your lines are tapering to nothing sooner than you want.
Step 5: Fix Canvas and Technique Issues
Some wobble has nothing to do with brush settings.
- Rotate the canvas so each stroke follows your hand's natural arc. Most people draw smooth curves in one direction and awkward ones in the other.
- Draw from the shoulder or elbow for long curves, and from the wrist or fingers only for short, detailed strokes.
- Draw at a deliberate speed. Very slow strokes amplify tremor, while confident, quick strokes tend to produce cleaner curves. Smoothing helps, but it can't replace commitment.
- Zoom out for long lines. Drawing a big curve while zoomed far in forces you to make tiny, uncertain movements.
- Warm up. A few loose ovals, arcs, and crosshatch lines before inking really do reduce wobble.
- Work at adequate resolution. If a line looks jagged when you zoom in, the canvas may be too small for the output size you need. Plan canvas dimensions before you start inking, since you can't add real detail later.
If the whole app feels laggy, a heavy canvas can cause visible delay between input and ink. Large canvases with many layers and big brush sizes strain the device, and that lag can read as roughness.
Fixing Strokes After You've Drawn Them
Smoothing at draw time is ideal, but you can still rescue existing lines.
- Undo and redraw the single stroke. With the right brush settings, this is usually faster than repairing it.
- Use the Eraser or Smudge tool with a smooth brush to trim ragged edges.
When You Should Turn Smoothing Down
Smoothing can flatten the energy out of a drawing. Reduce or disable it when you want:
- Loose gestural sketches with visible energy
- Intentional texture such as fur, frayed edges, or dry-brush effects
- Sharp corners, where heavy stabilization rounds off the point
- Precise technical detail, where lag gets in the way
A good workflow is to keep one duplicate of each favorite brush at several smoothing levels, such as "Sketch," "Clean," and "Ink." That way you switch brushes instead of digging into menus.
Quick Troubleshooting Checklist
Using Smooth Procreate Artwork in a Motion Pipeline
For motion designers and animators, Procreate is often where hand-drawn frames, style references, or character designs start. Clean linework matters more once those assets move into motion, because small wobbles become more noticeable when a drawing is animated, composited, or used as a reference for other tools.
Key Takeaways
- Duplicate a brush, then raise StreamLine Amount first. It's the most effective single change.
- Add Stabilization and Motion Filtering sparingly, because too much causes lag.
- Lower Spacing and zero out Jitter for clean, continuous lines.
- Use global smoothing as a temporary aid, and remember to turn it off.
- Technique matters: rotate the canvas, draw from the shoulder, and work at a resolution that suits your output.
- Keep smooth and loose brush variants side by side so you can switch by task.