How to Make Brush Strokes in Procreate
StyleFrame Team7 min read
To make a brush stroke in Procreate, pick a brush from the Brush Library, set its size and opacity with the sliders on the left, and drag your Apple Pencil or finger across the canvas. To make a stroke that behaves differently, swipe left on any brush, tap Duplicate, and open the copy in Brush Studio. There you can change its Shape, Grain, Stroke Path, StreamLine, and Taper settings.
Make a basic brush stroke
- Create a canvas and tap the brush icon in the top toolbar.
- Choose a brush category, then a brush. Hard inking brushes give crisp, consistent lines. Charcoal and paint brushes respond to pressure and tilt with texture and width changes.
- Set size with the top slider on the left edge and opacity with the bottom slider.
- Pick a color from the color disc and draw on a fresh layer, not your background.
Drawing on its own layer matters if the strokes are headed for a motion project. Each layer can be exported, hidden, or transformed independently, and you can adjust or redraw a stroke without touching the rest of the artwork.
Pressure matters as much as the brush itself. Light pressure usually gives thinner, more transparent marks, and heavy pressure gives thicker, denser ones. A few minutes of drawing the same stroke at different speeds and pressures will teach you more about a brush than reading its settings.
Control how strokes behave
Most of the look of a stroke comes from three settings, all reachable by tapping a brush to open Brush Studio.
StreamLine and Stabilization
StreamLine smooths wobble in a line. Higher Amount values give long, even curves, which suits inking, lettering, and any shape you plan to trace in After Effects. Lower values keep the natural tremor of a hand-drawn line. Stabilization works differently: it averages the stroke's movement, so higher values make strokes more deliberate and less jittery. You can set these per brush, or globally in the Accessibility settings if you want the same smoothing everywhere.
Taper
The Taper tab controls how a stroke thins at its start and end. Move the points on the Pressure Taper slider to lengthen or shorten each end. A pronounced taper gives a brush-pen or dry-brush feel. Little or no taper gives a mechanical, uniform line. If your strokes look flat and digital, taper is often the first thing to adjust.
Pressure response
Each brush reacts to pressure, but you can reshape that reaction globally in the Pressure and Smoothing preferences. If you press hard by habit, flattening the curve prevents strokes from turning thick and opaque too quickly.
Build a custom brush in Brush Studio
A Procreate brush is built from two ingredients: a shape (the stamp repeated along your path) and a grain (the texture shown through that shape). Combining them gives you a wide range of marks, from smooth ink to dry bristle.
Start from a duplicate
Always work on a copy. Swipe left on a brush and tap Duplicate, then tap the copy to open Brush Studio. If you'd rather start clean, create your own brush set from the top of the brush list and add a new brush inside it. A custom set keeps your work out of Procreate's default packs.
Choose a shape
Open the Shape attribute and tap Edit. Under Import, you can choose from the Source Library, which includes rough-edged shapes such as blotches, or bring in your own image. A round shape gives a clean line, while an irregular, ragged shape gives a stroke with bristly edges.
Add a grain
Open the Grain attribute and pick a texture. Grain adds the surface character: paper tooth, canvas weave, or dry-media scratches. Pairing a rough shape with a subtle grain usually reads as natural paint. Pairing a smooth shape with a strong grain reads as pencil or chalk.
Tune the Stroke Path
Stroke Path decides how the stamps are laid down:
- Spacing: Low spacing merges stamps into one continuous stroke. High spacing exposes the individual stamps as a row of shapes, which is how you make dotted lines or repeated patterns.
- Jitter (Lateral and Linear): Lateral jitter scatters stamps perpendicular to your stroke, while linear jitter pushes them along its direction. Together they produce a loose, sprayed or splattered edge.
- Fall Off: This fades a stroke as it travels, like a brush running out of paint. Raise it for quick fade-outs and lower it for strokes that hold their opacity.
Use the Drawing Pad inside Brush Studio to test as you adjust. Change one setting at a time, since stacking several changes makes it hard to tell which one produced the effect.
Make a brush from your own image
You can turn a scanned ink mark, a photographed brush stroke, or a graphic into a stamp brush. The most common problem is a blank result, and it nearly always comes down to how Procreate reads brightness: white is opaque and black is transparent.
- Save the source image as a JPG with a solid background, or as a PNG with a white design on transparent. A black design on a transparent PNG imports as an empty square.
- Import it as the Shape source, not the Grain, if you want it to be the stamp itself.
- Tap the imported image with two fingers to invert it if your marks appear reversed.
- Switch on Orient to Screen in General settings and raise Spacing in Stroke Path so the stamps read as separate marks.
For scanned real-world media, such as ink on paper or dry brush on cardboard, high contrast and a clean white background give the best results. Adjust levels before importing instead of trying to fix it inside Brush Studio.
Add an outline stroke to shapes
Procreate has no one-tap "add stroke" command for shapes or text, but there is a workable method:
- Duplicate the layer containing your shape.
- Select the bottom copy, then hold two fingers on its layer thumbnail to select its contents.
- Choose Color Fill and set the outline color.
- Open the Selection tool, increase Feather to roughly the stroke width you want, and exit the menu.
- Switch the selection mode to Automatic, with Color Fill still active, and tap the shape. Drag to set the stroke width and sharpen the edge.
You can tap other shapes afterward to apply the same outline quickly.
Get Procreate strokes into a motion pipeline
If your strokes are headed for After Effects, Premiere Pro, Cinema 4D, Blender, or Nuke, a few habits save time later:
- Keep elements on separate layers. That way you can animate, parallax, or retime each element.
- Work at your delivery resolution. Brush textures and grain can look soft or tile visibly if you scale a small canvas up in a comp. Set the canvas size before you begin.
- Plan frame-by-frame work around your compositor. Check which export formats your compositing software accepts before you start animating.
- Check the grain after export. Stroke textures can shimmer when a static grain sits under moving elements. Test a few frames in your compositor before committing a whole sequence.
Troubleshooting common brush problems
- Stroke looks blank or invisible: Check the shape source for a black design on a transparent background, or confirm that your color isn't matching the layer.
- Stroke looks jagged or dotted: Lower the Spacing, and check for high Jitter values.
- Texture changes when you resize the brush: Open the Grain settings and review whether it's set to move or stay fixed, then adjust scale and zoom behavior.
- Line feels wobbly: Increase StreamLine Amount or add Stabilization.
- Edits to a default brush disappeared: Duplicate before editing, so you can always return to the original.
Practice approach
Start by duplicating one familiar brush and change only one attribute at a time: first taper, then spacing, then grain. Save each version with a clear name. With practice you will have a small set of brushes that match your style, and you'll know which settings produce which marks. Those brushes then become the building blocks for illustrations, textures, and animated elements that you can bring into your motion projects.