How to Make Automatic Straight Lines on Procreate
StyleFrame Team7 min read
To make an automatic straight line in Procreate, draw a stroke with Paint or Erase selected and keep your Apple Pencil or finger held on the screen at the end of the stroke. After a brief pause (about half a second), the stroke snaps into a straight line, which you can still aim by moving the pencil. Touch a second finger to the screen while holding, and the angle locks to 15° increments, which gives you clean horizontals, verticals, and 45° diagonals. This feature is called QuickLine, and its sibling, QuickShape, does the same for circles, rectangles, triangles, and polylines.
How QuickLine works
QuickLine is built into Procreate's QuickShape gesture. You don't pick a ruler or switch tools. You draw, and the hold-at-the-end gesture tells Procreate to clean up the stroke.
- Open your canvas and select a brush (or the eraser). QuickShape works with both Paint and Erase.
- Draw a rough line in the direction you want.
- Don't lift. Keep the pencil or finger pressed at the end of the stroke.
- Wait for the line to straighten. A notification appears at the top of the screen when the shape is recognized.
- While still holding, drag to adjust the endpoint. The line pivots around the start point.
- Lift to commit.
The start point is where your stroke began, so place it deliberately. Straight lines in Procreate pivot around that first point, and you can't reposition it after you lift unless you use Transform.
Snap to 15° increments for exact angles
A line that is merely straight isn't always a line that's correct. For technical frames, UI mockups, storyboard panels, or layout grids, you usually need a true horizontal or vertical.
After the line straightens, and while you're still holding down, touch a second finger anywhere on the canvas. The endpoint now jumps in 15° steps relative to the start point. Move the pencil until you land on 0°, 45°, 90°, or whichever angle you need, then lift the pencil first and your other finger after.
This is the answer to most "my lines are almost horizontal" complaints. Without the second finger, the line is straight but follows wherever your hand drifted. With it, the angle is quantized.
Use QuickShape for rectangles, circles, and polylines
The same hold gesture handles more than single lines:
- Rectangles and triangles: Draw a rough version, hold, and the edges straighten. Add a second finger to push the shape toward a regular form, such as equal-length triangle edges.
- Circles and ellipses: Draw a loop and hold. The second-finger touch turns an ellipse into a true circle.
- Polylines: A multi-segment shape you sketch by hand can also be cleaned into consistent straight segments.
Right after the shape forms, tap the notification at the top of the screen to open the edit shape menu. There you can switch the shape type (a circle to a square, for example) and use the transformation nodes to fine-tune it. This menu is only available immediately after creating the shape. If you need changes later, use the Transform tool instead.
Adjust or disable the gesture
If the snap triggers too slowly, too fast, or not at all, check the gesture settings:
- Tap the Actions menu (wrench icon).
- Go to Prefs > Gesture Controls.
- Open the QuickShape section.
- Make sure the gesture is enabled (the "draw and hold" option), then adjust the delay to taste.
A shorter delay makes snapping feel immediate but increases the odds of accidental straightening if you pause mid-stroke while drawing curves. A longer delay is safer for organic sketching. If you never want the behavior, you can turn it off in the same panel.
Troubleshooting: lines only come out straight, or never straighten
Two opposite problems show up often.
Everything you draw is straight
First, confirm whether the shape notification appears at the top of the screen when it happens. If it does, QuickShape is firing. Increase the delay or disable the gesture in Prefs > Gesture Controls.
If there's no notification, something else is involved:
- Assisted Drawing: In Gesture Controls, open the Assisted Drawing tab and check whether Apple Pencil is toggled on. Also check the Layers panel. If the layer thumbnail says "Assisted," tap it and switch off Drawing Assist.
- Stabilization and smoothing: Very high stabilization values can make strokes feel locked or rigid. Go to Prefs > Pressure and Smoothing and tap Reset, then test with a couple of different brushes to rule out a custom brush setting.
- Input device: If you're drawing with your finger instead of a pencil, retest with each to see if the behavior changes.
The line never snaps
- Confirm QuickShape is enabled in Gesture Controls.
- Make sure you're holding at the end of the stroke without moving.
- Check that you have Paint or Erase active, not a tool like Smudge.
Drawing Guide and Drawing Assist for repeatable straight lines
QuickLine fixes individual strokes. When you need many consistent lines, such as parallel hatching, perspective lines, or a grid, consider Procreate's Drawing Guide and Drawing Assist instead. Turn on Drawing Assist for the layer you're working on to use it with your strokes.
The combination is practical: QuickLine for one-off lines, Drawing Guide for systematic geometry. Neither works like a traditional movable ruler, which is a complaint among some Procreate users. Some artists turn to other apps for that kind of tool. Autodesk Sketchbook offers a bendable ruler, Infinite Painter includes fixed shapes and guides, and Ibis Paint has an array-style guide setup. If a physical-style ruler is central to your work, those are worth testing, but for most storyboarding and design-frame tasks, QuickLine plus Drawing Guide is enough.
Getting straight-line work into a motion pipeline
For motion designers, animators, and editors, Procreate is usually a front-end step: boards, animatics, design frames, hand-drawn elements, or texture and line passes. The straight lines you build there have to survive the trip into After Effects, Premiere Pro, Cinema 4D, Blender, or Nuke.
A few habits make that smoother:
- Keep line work on its own layers. Separate geometry, hand-drawn accents, and fills so you can recolor or retime elements later.
- Work at the final delivery resolution (or higher). Straight lines show every pixel stair-step if you scale a small canvas up in compositing.
- Export with transparency. Choose a format that keeps transparency, and one that preserves layers if your compositing app needs them.
- Name layers and exports consistently. Predictable naming saves time when you're importing dozens of frames.
- Snap before you animate. A line corrected at 15° increments in Procreate is easier to rig and track than one that's off by two degrees.
Quick reference
FAQ
Why doesn't my line straighten? Usually the gesture is disabled, you moved before the delay finished, or the active tool doesn't support QuickShape. Check Gesture Controls and hold still at the end of the stroke.
Can I move the start point after the line snaps? Not during the gesture. Reposition the finished line with Transform.
Does this work with a finger instead of an Apple Pencil? Yes. The same hold gesture works with either.
How do I stop accidental straight lines? Lengthen the delay or turn QuickShape off in Gesture Controls.
Is there a ruler tool? Procreate relies on QuickShape and the Drawing Guide rather than a movable ruler, and some users have asked for one.