How to Make an Image Opacity in Procreate Ipad
StyleFrame Team8 min read
To make an image transparent in Procreate on iPad, insert it as a layer, open the Layers panel, tap the N to the right of the layer name, and drag the Opacity slider left. A faster route is to tap the layer with two fingers and slide left or right on the canvas to lower or raise opacity. Both methods are non-destructive, so you can change the value again at any point.
What opacity means in Procreate
Opacity describes how visible pixels are. At 100% a layer is fully solid, and at 50% it is half see-through. Procreate lets you control it in three places: on a brush, on a whole layer, or on a selection. Which one you use decides whether you can revise the result later.
For an imported image, layer opacity is almost always what you want. The image sits on its own layer, and the slider controls how much of it shows through to whatever is beneath. If you come from After Effects, this is the same idea as a layer's Opacity property.
Step 1: Get the image onto its own layer
You can't adjust image opacity until the image has its own layer.
- Open your canvas.
- Tap the Actions icon (the wrench).
- Choose Add, then Insert a photo (or Insert a file, depending on where the image is saved).
- Select the image. It lands on a new layer, with the Transform tool active so you can scale and position it.
- Tap the Transform tool again, or tap another tool, to commit placement.
If you're working from reference material, such as a styleframe, a texture, or a screenshot from a comp, put it on its own layer so it never mixes with your painted work.
Step 2: Change layer opacity (the standard method)
This is the answer for most people, and it keeps everything editable.
Method A: The N button
- Tap the Layers icon in the top right (two overlapping squares).
- Find your image layer.
- Tap the small letter to the right of the layer name. It reads N by default, for Normal blend mode.
- A panel opens with blend modes and an Opacity slider at the top.
- Drag the slider left to reduce opacity or right to increase it. The percentage appears beside the label.
This method also puts blend modes right below the slider, which helps when you're deciding between a plain fade and something like Multiply or Screen.
Method B: The two-finger tap
- Open the Layers panel.
- Tap the image layer with two fingers at the same time.
- An opacity bar appears at the top of the screen.
- Slide your finger or Apple Pencil left to make the layer more transparent, or right to make it more solid.
Many artists prefer this method because the layer's opacity changes live on the canvas while you watch. It's also quick when you're balancing several layers against each other.
Because you can return to either control and change the value, layer opacity is non-destructive. The original pixels are never altered.
Step 3: Use the Opacity adjustment when you need it
Procreate also has an Opacity tool under the Adjustments menu (the magic wand icon).
- Select the layer you want to change.
- Tap Adjustments, then Opacity.
- Slide your finger left or right across the screen. A bar at the top shows the current value, starting at 100%.
- Use the buttons at the bottom to cancel, undo, redo, or reset.
- Tap the Adjustments icon again, or select any other tool, to commit.
The difference between this and the layer slider is important. The Adjustments version applies the change when you commit it, so it behaves more like a one-time edit than a live property. You can undo it right away, but you can't keep revisiting it as a adjustable setting the way you can with the layer slider. Use it only if you specifically want that behavior. For most work, stick with the N panel or the two-finger gesture.
Step 4: Change opacity on part of an image
Sometimes only a region needs to be transparent, for example to fade one edge of an image into the background.
Using a selection:
- Tap the Selection tool and pick your preferred method.
- Make your selection on the image layer.
- Open Layers and tap the layer with two fingers.
- Slide left on the canvas to reduce the opacity of the selected area, or right to increase it.
- Exit the mode to apply the change.
Treat this as destructive. Once you leave the mode, the change is applied to the pixels. You can undo immediately, but you can't return later and tweak the same percentage. Duplicate the layer first if you want a safety copy.
Using the Eraser with a soft brush:
For gradual fades, a soft eraser with reduced brush opacity is often better than a selection. Set the eraser's opacity with the lower slider on the left sidebar and build up the fade in light passes. This is also destructive, so work on a duplicate or use a layer mask-style approach (see below).
Step 5: Brush opacity versus layer opacity
It's easy to mix these up, and it's a common reason people think opacity isn't working.
- Brush opacity is the lower slider on the left sidebar. It controls how strong each new stroke is.
- Layer opacity controls the whole layer, including everything already painted on it.
Many brushes also respond to Apple Pencil pressure. If your brush opacity is set to maximum but strokes still look faint, the cause may be pressure sensitivity rather than the slider. In that case, check the brush's pressure settings.
If you paint over an image on the same layer, you can't later change the painting's opacity separately from the image's. Keep painting on separate layers above the image.
Non-destructive fading with clipping masks
A clipping mask lets you paint or adjust inside the shape of the layer below it. To use one:
- Add a new layer above your image layer.
- Tap the new layer and choose Clipping Mask.
- Paint on the new layer. Strokes show only where the image layer has pixels.
You can then change the opacity of the clipped layer independently, which keeps the underlying image untouched. This is useful for tinting an image, adding a gradient fade, or building a texture overlay without ever editing the original.
Common problems and fixes
The slider doesn't seem to do anything. Check that you've selected the correct layer. Only one layer is adjusted at a time, and the highlighted layer is the active one.
The image looks washed out even at 100%. The blend mode may have changed from Normal. Tap the letter next to the layer name and reset it.
The image has a white box around it. The image itself may have a white background. Use a selection or the Automatic selection tool to isolate the subject and delete the rest, or use a transparent PNG to begin with.
The transparency disappears on export. A JPEG can't hold transparency, and a visible background color layer will fill empty areas. Hide the Background color layer in the Layers panel and export as PNG, or export a layered PSD if you want to keep the layers.
Taking Procreate opacity work into a motion pipeline
If your Procreate file is a start point for animation or compositing, exporting with care saves time later.
- PNG with transparency is simplest for single elements. Hide the background layer first.
- PSD keeps layers separate, so you can bring them into After Effects as individual layers and animate their opacity with keyframes there. Procreate's static opacity values give you a starting look, but keyframed fades belong in your compositor.
- Layer discipline matters. Keep the image, painted overlays, and effects on separate named layers, so they arrive in After Effects ready to use.
Opacity here is a static look decision, and any animated version of it happens downstream.
Where Styleframe fits
Once you've built a layered still in Procreate, such as a character pose, a background, or a key frame with a deliberate look, you may want to move it into motion without redrawing every frame. Styleframe is an AI video and motion tool built for artist control rather than one-click output. Generation is driven by your own references: images, video clips, and keyframes.
Treat it as a way to extend your Procreate frames into motion, not as a replacement for your compositing setup.
Quick reference
For nearly every case involving an inserted image, the N button on the layer is the right place to start. It's visible, precise, and fully editable, which is exactly what you want when the file will later feed a motion project.