How to Make a Two Color Brush in Procreate
StyleFrame Team7 min read
To make a two color brush in Procreate, duplicate a brush, open Brush Studio, and in Color Dynamics raise the Secondary Color slider under Color Pressure (or Color Tilt). Then set a primary and secondary color in the color panel. Light pressure gives you one color and heavier pressure blends toward the other. For an outline-and-fill look in a single stroke, combine two brushes into a Dual Brush and edit each half separately.
Two ways to get two colors from one stroke
Procreate has two separate mechanisms that people both call a "two color brush." They behave differently, so pick based on the result you want.
Neither method requires third-party tools. Both are built into Procreate, so any brush you make remains editable.
Method 1: Build a two color brush with Secondary Color
This is the fastest route, and it works on almost any brush you already own.
1. Duplicate the brush
Swipe left on the brush thumbnail in the library and tap Duplicate. Editing the copy keeps your original intact. You can also set a reset point in Brush Studio under About this brush, which lets you roll back to a known-good state after experimenting.
2. Open Color Dynamics
Tap your duplicate to enter Brush Studio, then choose Color Dynamics in the left column. Set every slider to zero first. Starting from a clean slate matters because leftover hue, saturation, or brightness jitter will make the color change look random rather than controlled.
3. Raise Secondary Color and Saturation
Under Color Pressure, push the Secondary Color slider to its maximum. Push Saturation to maximum as well. If you want the shift to respond to Apple Pencil angle, make the same changes under Color Tilt. You can use pressure only, tilt only, or both.
4. Set your two colors
Tap Done, then open the color panel. Most panels (everything except Palettes) show two small swatches at the top right. Tap one and choose your primary color, then tap the other and choose your secondary color.
5. Test the stroke
Draw with light pressure and you should see one color. Increase pressure and the stroke moves toward the other. If the transition feels abrupt or never reaches the second color, return to Brush Studio and double-check your Color Dynamics values.
Note that not every color dynamics brush uses the secondary color. The brush needs those specific settings, which is why you configure it explicitly rather than relying on a default brush.
Method 2: Build a two color brush with a Dual Brush
A Dual Brush merges two brushes so a single stroke contains both. Because each component keeps its own shape and grain, this is the better route when you want distinct layers within a stroke, such as a thick outline behind a thinner fill.
Combining the brushes
- Open the Brushes library from the Paint, Smudge, or Erase button.
- Tap the first brush. It highlights bright blue and becomes the Primary.
- Swipe to select the second brush. It highlights dark blue and becomes the Secondary.
- Tap Combine at the top right of the library.
Some rules to know before you start:
- Both brushes must live in the same brush set. If they don't, drag one into the other's set first.
- You can only combine single brushes. An existing Dual Brush can't be combined with anything else.
- Since Procreate 5.4, default brushes can be combined as long as they aren't already Dual Brushes.
- The new brush takes the Primary brush's name. Tap and hold, then choose Rename if you want something clearer.
Editing each half independently
Tap the Dual Brush to enter Brush Studio. The top left shows previews of both component brushes. Tap one and a blue line appears beside it, which means your edits now apply only to that brush. This is where you tune the settings for each layer without affecting the other.
Using Combine Mode
Tap either preview to expand the panel and reveal Combine Mode. It defaults to Normal, and the options work much like layer blend modes. Selecting a mode updates the result live on the drawing pad, so cycle through a handful and see which gives you the interaction you want. If you're used to older Dual Brush behavior that relied on Normal, there's a toggle at the bottom of the Rendering tab in Brush Studio that you can try.
Uncombining
If a combination doesn't work, open Brush Studio, expand the Secondary brush preview, and tap Uncombine. You get your two original brushes back.
A practical recipe for an outline-and-fill brush
A common technique for drawing "once and getting two colors" starts from a simple monoline brush. The approach below follows that idea, and you should treat the numbers as starting points to tune by eye rather than fixed rules.
- Duplicate the monoline brush twice and move both copies into a fresh brush set, so they can combine.
- Edit each brush before combining. Adjusting settings first is more precise than editing afterward, since you can see each component's behavior on its own.
- Tune the stroke behavior. One working setup uses a Stroke Path spacing of around 10 and the Streamline amount under Stabilization pushed to maximum for smooth lines.
- Adjust Rendering. One working setup sets the rendering mode to Uniform Glaze and raises Burnt Edges all the way up.
- Differentiate the two halves. Make one brush larger to act as the outline, and give the smaller one the secondary color behavior from Method 1 so it picks up your second color.
- Combine, then fine-tune each half and the Combine Mode until the outline and fill sit together cleanly.
Because this is a stack of interacting settings, expect a few rounds of adjustment. Keep a reset point on each component so you can back out cleanly.
Troubleshooting
- The second color never appears. Check that Secondary Color is raised under the Color Dynamics section you're actually using (Pressure versus Tilt), and that your two swatches are different colors.
- Colors look random, not controlled. Other Color Dynamics sliders (hue, brightness, stroke jitter) are still above zero. Reset them.
- Combine option doesn't appear. The brushes are probably in different sets, or one is already a Dual Brush.
- Edits affect both halves. You haven't selected one component in Brush Studio. Look for the blue line next to the preview.
- The brush looks different after combining. Try different Combine Modes or the Rendering toggle for older Normal behavior.
Taking Procreate artwork into a motion pipeline
If you're a motion designer, animator, or compositor, a two color brush is mostly useful for generating hand-drawn assets: lettering, outlines, texture passes, and frame-by-frame elements. Procreate handles the drawing. The harder part is getting that material moving in a professional pipeline.
Export your artwork as layered or flattened files and bring it into After Effects, Nuke, or Blender the way you would any other 2D source. Keep the outline and fill on separate layers where you can, so you retain flexibility for timing, color correction, and compositing.
Tips for building a reusable brush set
- Name brushes by function, like "Outline Fill – Bold," so they're easy to find mid-project.
- Keep components together. Store both halves of a Dual Brush in the same set, since brushes must be in the same set to combine.
- Save reset points before every major change.
- Test on a dark and light canvas. Saturation and blend behavior can look very different against different backgrounds.
- Test at the sizes you'll actually use. A brush that reads well large can lose its outline at small sizes, and spacing may need to shift.
Which method should you use?
Use Secondary Color when you want a color shift that responds to how you draw: pressure for shading, tilt for expressive variation. Use a Dual Brush when you want two structurally different strokes, like outline and fill, laid down together. If you want both effects, combine them: build the secondary-color behavior into one component of a Dual Brush, as in the outline recipe above.
Either way, the workflow is the same: duplicate before editing, change one setting at a time, test often, and save a reset point you trust. Once the brush behaves, you have a repeatable look you can carry from Procreate into the rest of your motion pipeline.