How to Make a Tie Dye Effect on Procreate
StyleFrame Team7 min read
To make a tie dye effect in Procreate, fill a square canvas with four saturated color blocks on a single layer, then drag the Liquify tool's Twirl mode from the center outward until the colors spiral. Finish with a soft blur, some grain, and a Multiply texture so it reads as dyed fabric rather than a digital gradient. For a repeatable tool, you can also modify a stock brush such as Blotchy so it paints spaced, curved dye marks that follow your stroke.
Set Up the Canvas and Palette
Start with a square canvas. If the result is headed into a motion project, don't use a small tutorial-sized canvas. Work at 4000 × 4000 px or larger so you can crop, scale, and animate the texture later without it going soft. Keep your layer stack lean.
Choose your palette before you paint:
- Keep the palette limited. Four is a comfortable starting point, for example green, yellow, pink, and purple.
- Keep the values distinct. Tie dye reads well when neighboring hues differ in brightness, so the swirl stays legible after blending.
- Save the palette. Create a new swatch set in the Color panel so you can reuse it across variations.
White gaps between dye bands are part of the look. Think about whether you want them. A touch of off-white between colors sells the resist-dye feel more than a fully saturated field.
Method 1: Liquify Swirl (Fastest, Most Controllable)
This is the most common approach and the one that gives you a classic spiral.
Step 1: Block in the colors
Turn on the 2D drawing guide (wrench tool > Drawing Guide > Edit Drawing Guide) and set the grid so it divides the canvas cleanly. Use the Rectangle selection in Add mode to fill quadrants with each palette color. Alternatively, skip the grid and paint rough wedges with a hard-edged brush. A grid gives you tidy, even bands, while freehand wedges give you a more organic result.
If you want a radial look from the start, paint pie-slice wedges instead of rectangles. Liquify has less distortion work to do, and the center of the spiral stays tighter.
Step 2: Merge and back up
Merge the color layers into one, then duplicate it. Hide the original as a safety copy. Liquify is destructive, so a clean backup layer is cheap insurance.
Step 3: Twirl with Liquify
Open Adjustments (the magic wand icon) and choose Liquify. Select a Twirl mode, then set:
- Size: large.
- Pressure: moderate.
- Distortion: moderate, because a high setting rotates the pixels too violently and creates jagged artifacts.
- Momentum: a little, which smooths the transition as you drag.
Press and hold at the center of the canvas, letting the twirl accumulate. Move slightly off-center and repeat. Each press wraps the color bands tighter around the point. Switch to a smaller size to drag stray bands and soften awkward corners.
Work in multiple passes rather than one heavy-handed one. Tie dye has a hand-folded irregularity, so a perfectly symmetric spiral looks more like a vector gradient than fabric.
Step 4: Soften the edges
Go to Adjustments > Gaussian Blur and apply a small amount to the layer. This simulates dye bleeding into cloth. Too much blur turns the whole thing into a smear. You want the boundaries to be soft but still distinguishable.
Method 2: Build a Tie Dye Brush
If you need to paint tie dye into shapes, such as lettering, a T-shirt mockup, or a character costume, a brush works better than Liquify, which affects the whole layer.
- Open the Brush Library and create a new set.
- Duplicate a stock brush with strong texture. Blotchy in the Calligraphy set works well.
- Drag the duplicate into your new set and open it in Brush Studio.
- Under Stroke Path, increase Spacing to roughly 50 percent so you get gaps between stamps, similar to folded and tied cloth.
- Turn Scatter and Jitter off so marks stay on your path.
- Under Shape, set rotation to Follow Stroke, and squash the shape slightly so the mark is elongated rather than round.
- Under Properties, raise the maximum size so you can cover large areas with a single pass.
Paint in curves, concentric arcs, or spirals, and change colors between passes. Because the brush uses one color per stroke, the multi-color effect comes from overlapping. Where two hues meet and overlap, you often get secondary colors that look like natural dye mixing.
Method 3: Layered Watercolor Overlap
A third approach avoids Liquify and uses wet-looking brushes in layers:
- Paint each color on its own layer with a soft, textured watercolor brush.
- Overlap the shapes at their edges.
- Set upper layers to Multiply so the overlaps darken and blend into mixed tones.
- Use Alpha Lock or a Clipping Mask on a layer when you want to recolor a shape without losing its edges.
This method is slower but gives the most painterly result, and it keeps each color on its own layer, which matters if you want to animate or recolor them separately later.
Add Fabric Texture and Dye Bleed
A flat swirl looks like a gradient. A few finishing steps push it toward cloth:
- Noise: Adjustments > Noise, a low value, adds fiber-like grain.
- Texture layer: Add a canvas, linen, or paper texture above the artwork and set it to Multiply or Overlay at reduced opacity.
- Wrinkle pass: Paint a few thin, irregular, lighter lines with a dry brush at low opacity. These mimic the creases where cloth was bound.
- Color shift: Use Adjustments > Hue, Saturation, Brightness on a duplicate layer, then mask it in to vary color across the surface.
Look at the result at 100 percent zoom. If banding or smearing shows, undo the last blur or Liquify pass and reduce its strength.
Export for a Motion Pipeline
For motion designers, Procreate is usually where the texture gets made, not where the final shot lives. Export with these settings in mind:
- PNG for a flat, high-quality still. PSD if you want to preserve the layers and recolor or animate them in After Effects.
- Keep a version without any mockup or border so you can extend or tile it.
- If you want a looping background, build a seamless version by offsetting the canvas and painting over the seams, then test the tile before export.
Once the file is in your compositing software, you have several options for animating it:
- Apply displacement or warp effects at low amounts to make the dye appear to flow.
- Use a twirl effect for a slow spin from the center.
- Use a noise pattern as a displacement map for organic, drifting movement.
- Blend the artwork over footage with blend modes for tie dye color grades and title backgrounds.
The same artwork can also be used as a texture in 3D software.
Common Problems and Fixes
The swirl looks jagged. Lower Distortion and Pressure in Liquify, and work in several lighter passes.
Colors turn muddy. Your palette probably has too many mid-value hues. Reduce the number of colors, or keep clean separation between bands before twirling.
It looks too digital. Add grain, a fabric texture, and slight irregularity. Avoid perfect symmetry.
The brush stamps look like beads. Increase stroke smoothing, or lower Spacing so marks connect into a continuous band.
It goes soft when scaled up. Start at a higher resolution, or upscale the final piece before compositing.
Quick Workflow Summary
- Create a large square canvas and save a four-color palette.
- Block in color wedges or rectangles, then merge and duplicate.
- Twirl with Liquify in several light passes, cleaning up with a smaller size.
- Soften with a small Gaussian Blur.
- Add noise, texture, and creases.
- Export PNG or PSD and bring it into After Effects, Cinema 4D, or Blender.
- Animate it with displacement or twirl effects.
Learn the Liquify method first, because it produces the classic look quickly. Then add the brush and layered methods once you need more control over where the dye lands.