How to Make a Slowly Varying Color in Procreate
StyleFrame Team7 min read
To make a slowly varying color in Procreate, build a smooth gradient and let it shift gradually: blur two adjacent color fields together, map a grayscale ramp through Gradient Map, or paint a Hue/Saturation/Brightness adjustment in Pencil mode with a soft brush. For strokes that change color as you draw, use Color Dynamics in Brush Studio to blend between a primary and secondary color. If the color needs to drift over time, paint the gradient in Procreate and animate the hue in After Effects.
What "slowly varying" means in practice
The phrase covers three different jobs, and each has a different best tool.
- Varying across space: a background, sky, or surface where color shifts gradually from one area to another. This is a gradient problem.
- Varying along a stroke: a line or brush mark that drifts from one hue to another as you draw. This is a brush-dynamics problem.
- Varying across time: a color that evolves over seconds in a clip. This is an animation problem, and it usually leaves Procreate.
Most motion work needs the first or third. Procreate is a good place to author the source art, as long as you know where its limits are.
Method 1: Blur two color fields together
This is the most direct way to get a gradient.
- Create a new layer and fill the top half of the canvas with your first color and the bottom half with your second. A selection plus ColorDrop, or a large flat brush, works fine.
- Open Adjustments > Gaussian Blur and choose Layer mode.
- Drag across the canvas to raise the blur until the hard edge dissolves into a long transition.
The transition width depends on the blur amount, so push it higher than feels necessary. A slowly varying color needs a long, soft ramp, and a small blur gives you a visible band instead. For more than two colors, stack three or four bands and blur them together.
Method 2: Use Gradient Map for controlled ramps
Gradient Map gives you the most control over which colors appear and where.
- Paint a grayscale ramp on its own layer: a soft airbrush from black to white, or the blurred two-field method above in gray.
- Open Adjustments > Gradient Map and pick or build a color ramp.
- Tweak the ramp stops so each color sits where you want it.
The advantage is that the luminance layer and the color ramp are separate decisions. You can reshape the grayscale ramp, or swap the palette, without repainting. That separation is useful when a client changes the palette late. For the broader tonal tools, Curves, and Color Balance, Procreate's handbook explains the interfaces in detail.
Method 3: Paint the adjustment with Pencil mode
Procreate's Hue, Saturation, Brightness adjustment normally affects an entire layer. In Pencil mode, you apply the adjustment only where you draw, and the brush's softness and opacity control how much.
- Select the layer you want to recolor.
- Tap Adjustments > Hue, Saturation, Brightness.
- Switch from Layer to Pencil at the bottom of the screen.
- Set your brush to a soft airbrush with low opacity and paint gradually across the area.
- Move the Hue slider to your target and keep building up the effect in passes.
Because each pass adds a little more of the shift, the hue changes gradually and you can follow a form instead of a straight line. This suits illustrated surfaces such as a sunset on a character, or a rim light that drifts from warm to cool.
Method 4: Use Color Dynamics for color that varies along a stroke
If you want the color to change as you draw, set it up in the brush itself.
- Pick a primary color and a secondary color in the Color panel.
- Open the brush in Brush Studio and go to Color Dynamics.
- Adjust the stroke and pressure options so the brush blends between the primary and secondary colors as you work. Use the jitter sliders for hue, saturation, and brightness sparingly.
- Test on a scratch layer and refine.
Keep jitter values low. High values produce noise, while low values give a gentle drift that reads as natural variation. For a smooth progression across a long stroke, pair a soft brush with a slow, steady hand.
Method 5: Layer a Color blend mode over existing art
If the artwork already exists, you can add a gradient of color without touching the original pixels.
- Create a new layer above your artwork and clip it as a Clipping Mask.
- Set its blend mode to Color.
- Paint broad, soft strokes with different hues, letting them overlap and blend.
- Lower the layer opacity to taste.
Overlapping soft strokes at partial opacity build up a gradual color transition, and the underlying linework and values stay untouched. This is the non-destructive route, and it's easy to revise.
Avoid banding in slow gradients
Slow, low-contrast gradients are the most likely to show visible steps, especially after video compression. A few habits help:
- Add a little grain: a subtle Noise adjustment on a gradient layer breaks up the steps.
- Work at your final resolution so you don't scale up a soft gradient later.
- Don't stack heavy contrast adjustments on top of a gradient layer.
- Check the gradient on a calibrated display, not only on the iPad.
If the file is destined for video, expect banding to be more visible after encoding. Adding grain in your compositor is often the final fix.
Making color vary over time
Procreate's Animation Assist is frame-based, so each frame needs its own color state. You can adjust hue per frame, but a slow drift across 240 frames done by hand is tedious and error-prone. Procreate Dreams offers keyframed animation, so check whether the effect you need is available there. For many pipelines, the more reliable approach is to paint the gradient once and animate it elsewhere.
In After Effects
-
Export the artwork from Procreate as a PNG or layered PSD. Keep the gradient on its own layer.
-
Import it into After Effects and apply Hue/Saturation or Colorama.
-
Keyframe Master Hue, or drive it with an expression. For a steady drift, apply this to the Master Hue property:
time * 12For a back-and-forth shift that eases naturally:
Math.sin(time * 0.5) * 30 -
Ease the keyframes in the Graph Editor so the change doesn't start or stop abruptly.
Alternatively, build the gradient natively with Gradient Ramp and animate the start and end colors. Use the Procreate art as a texture or matte on top. The same logic applies in Nuke with a HueShift or ColorLookup node, in Blender with a Hue/Saturation/Value node driven by keyframes, and in Premiere Pro with Lumetri's hue controls.
Where Styleframe fits
If you need the color drift to carry through painted, stylized motion rather than a flat hue shift, Styleframe can pick up where Procreate leaves off. It is an AI video and motion tool built for artistic control, and every generation is driven by your own inputs: reference images, video clips, and keyframes.
A practical setup looks like this:
- Frames-to-Video: paint two or three Procreate frames of the same scene in different color states, such as a warm dawn and a cool dusk. Use them as keyframes and generate the motion between them.
- Restyle and Ink-and-Paint: apply a Procreate painting as a style reference to existing footage so the footage inherits the palette and brush character.
- 4K Upscale: bring the result up to production resolution.
You can try several palettes or keyframe pairs without losing earlier versions. The output can be brought into After Effects or Nuke where you grade, composite, and finish. The aim is to keep your compositing workflow intact, not replace it. Results still depend on your references and keyframes, so expect to iterate.
Quick decision guide
Final tips
Keep the gradient on its own layer so you can swap, rotate, or animate it later. Make transitions longer than feels necessary, since slow variation reads best when the ramp is wide. Test on the final display and codec early, and add grain before you decide a gradient needs more colors. With the source art clean and separated, the same Procreate file can feed a still, a comp, or an animated sequence.