How to Make a Procreate Brush Full Opacity
StyleFrame Team7 min read
To make a Procreate brush full opacity, duplicate the brush, open it in Brush Studio, go to Properties, and set both the minimum and maximum opacity to 100%. Then raise the Opacity slider in the sidebar to the top, and check that you're painting on a layer at 100% opacity. If strokes still look see-through, the cause is usually Apple Pencil pressure, a glaze rendering mode, opacity jitter, or a grayscale brush source.
Why a Procreate brush won't paint fully opaque
"Opacity" in Procreate applies at several levels, and any of them can cap how solid a mark looks:
- The sidebar slider sets the brush's overall opacity.
- Brush Studio settings control how opacity responds to pressure, tilt, speed, and jitter.
- The brush's source images (Shape and Grain) define how solid each pixel of the stamp is.
- The layer you paint on has its own opacity and blend mode.
Some brushes are also built to never be fully opaque. The Gouache brush in the Painting set, for example, is meant to leave translucent marks, so you may not be able to fix it without rebuilding the brush. If a brush looks solid under your finger but faint under the Apple Pencil, the cause is often pressure sensitivity, which you can change.
Quick fix: set minimum and maximum opacity to 100%
This is the main method, and it works for many pressure-driven brushes.
- In the Brush Library, swipe left on the brush and tap Duplicate. Work on the copy so the original stays untouched.
- Tap the duplicate to open Brush Studio.
- Open the Properties tab.
- Drag both the Maximum Opacity and Minimum Opacity sliders to 100%.
- Tap Done and test a few strokes at light and heavy pressure.
Setting the minimum to 100% is the important part. It keeps the brush from dropping below full opacity however lightly you press. Setting only the maximum lets pressure still pull the opacity down.
Check the sidebar opacity slider and your layer
Before you edit the brush, rule out the simple causes:
- Drag the lower slider on the left sidebar all the way up. It's easy to nudge it by accident.
- Open the Layers panel, tap the N next to the layer name, and confirm the layer opacity is 100%.
- Check that the blend mode is Normal and that you aren't painting on a clipping mask that restricts where paint lands.
- Try painting on a brand-new layer. If the problem disappears, the original layer was the culprit.
This is quick and often solves "my brush is suddenly transparent" complaints.
Fix pressure sensitivity for Apple Pencil
If your brush looks fine with a finger but faint with a Pencil, pressure is capping your opacity. You have two options:
Adjust the brush's pressure response. In Brush Studio, open the Apple Pencil section and look at the pressure settings for opacity. Reducing or removing the opacity response means pressure no longer thins out the mark.
Adjust the global pressure curve. Go to Actions > Prefs > Edit Pressure Curve. The default is a straight diagonal line, which can require a lot of force to reach full opacity. Bending the curve so lighter pressure produces more output makes full opacity far easier to reach on every brush at once. This is a good fix if you want solid marks without editing each brush individually.
Brushes that fit this category include the default Round Brush and Flat Brush in the Painting set. They can reach full opacity, but only with the right pressure.
Turn off glaze and opacity jitter
Two settings in Brush Studio quietly keep strokes semi-transparent even when the sliders say 100%.
Glazed rendering
If a brush uses a glazed rendering mode, it paints translucent strokes that build up color when you go over them, but don't build up within a single continuous stroke. Switch the brush's rendering mode to Normal and the stroke paints solid. Sources describe this under different tabs, so look through the Rendering and Dynamics sections of Brush Studio if you can't find it right away.
Jitter on opacity
Under Dynamics, an opacity jitter value above zero makes each stamp land at a slightly different opacity. This is especially noticeable on stamp brushes, where each placement looks lighter or darker than the last. Pull Opacity Jitter down to 0 and the stamps become consistent.
Also check Taper, tilt settings, and any dilution options if you've confirmed everything else.
Fix custom brushes caused by source images
If you built your own brush and it always paints around 50% opacity, check the Shape and Grain source images. Procreate reads them like this:
- White paints fully opaque.
- Black is fully transparent.
- Gray is semi-opaque.
Color images register as grayscale, so a colored source image will produce a semi-opaque brush. The fix is to make the source black and white. A common approach is to draw black on a white background and invert it when you import it, using the invert button in the source panel or a two-finger tap on the source slot. Also confirm the shape itself is truly white where you want solid paint, and not light gray.
Get hard, fully opaque edges
Sometimes "full opacity" means no semi-transparent pixels at all, which matters for pure black-and-white line art or pixel-style work. Even with opacity at 100%, a brush can leave soft pixels around the edges because of anti-aliasing.
To remove them:
- Open the brush in Brush Studio and go to the Shape settings.
- Set Shape Filtering to No Filtering.
- Make sure the shape source has no gray or transparent pixels.
This fixed stray partial-opacity pixels for one artist who wanted pure black-and-white line work. For a ready-made option, the Syrup brush in the Inking set is one artist's go-to because it lays down solid, aliased marks. Many Inking brushes keep opacity at or near full, so starting from one is often easier than modifying a pressure-sensitive painting brush.
Troubleshooting checklist
Work through this in order, since each step is quick:
- Sidebar opacity slider is at the top.
- Layer opacity is 100% and blend mode is Normal.
- Brush minimum and maximum opacity are both 100%.
- Pressure response for opacity is reduced, or your pressure curve is adjusted.
- Rendering mode isn't a glaze mode.
- Opacity Jitter is 0.
- Shape and Grain sources are pure black and white, with white where you want solid paint.
- Shape Filtering is off if you need crisp, fully solid edges.
- The brush isn't one designed to be translucent, like the Gouache brush.
If you still see buildup or darker overlaps when you intentionally paint below 100%, a different approach works: paint with a fully opaque brush on a layer, then lower that layer's opacity. Overlapping strokes won't stack, because the transparency applies to the whole layer rather than to each stroke.
Why this matters for motion and VFX work
If you use Procreate to make frames, textures, mattes, or storyboard art for After Effects, Nuke, or Blender, partially transparent pixels cause real problems downstream. Semi-opaque fills show background bleed-through, edges with stray alpha create fringing when you composite, and inconsistent stamp opacity produces flicker when you cycle hand-drawn frames. Setting your brushes to predictable full opacity gives you clean alpha and cleaner source material before it reaches your compositing app.
A practical routine: build a small set of duplicated brushes (a solid fill brush, a hard-edge line brush, and a textured brush with opacity locked) and export your art as PNGs with transparency. These hold up better when you pull them into a layered comp.
Using opaque Procreate art in a Styleframe workflow
Clean, fully opaque artwork also makes better reference input for AI-assisted motion tools such as Styleframe. Because your source art has predictable edges and no accidental transparency, it's easier to judge what the tool is doing with your style.
Summary
Making a Procreate brush full opacity is usually a matter of finding which layer of opacity control is limiting you. Start with the sidebar slider and layer settings, then set the brush's min and max opacity to 100% in a duplicate. If strokes are still faint, adjust pressure, switch off glaze, zero out opacity jitter, and check that your brush sources are pure black and white. For crisp, fully solid edges, turn off shape filtering. Work on a duplicate brush each time so you can always return to the original.