How to Make a Pressure Sensitive Brush in Procreate
StyleFrame Team6 min read
To make a pressure-sensitive brush in Procreate, duplicate an existing brush, open Brush Studio, and go to the Apple Pencil tab. Raise the Pressure sliders for Size or Opacity until the stroke reacts to how hard you press. Then refine the feel with the brush's Taper settings and, only if needed, the global pressure curve under Actions → Prefs → Pressure and Smoothing.
How Pressure Works in Procreate
Pressure behavior comes from two layers, and mixing them up causes most of the confusion.
- Per-brush settings live in Brush Studio. They decide what pressure affects, such as width or opacity.
- The global pressure curve lives in Actions → Prefs → Pressure and Smoothing. It decides how pressure input maps to effect across every brush. The X axis is how hard you press, and the Y axis is how strongly the brush responds.
Build the behavior at the brush level first. Treat the global curve as a hardware-calibration tool for your hand and stylus, not a brush-design tool.
Step-by-Step: Build a Pressure-Sensitive Brush
1. Duplicate a brush instead of editing the original
Open the Brush Library and duplicate a brush you like. A copy lets you experiment without damaging a default brush. A Procreate forum answer points to resetting a brush to its defaults when results look strange, so keeping a clean original around saves time.
A plain round brush is a good starting point if you want a textureless line. The default Round brush has no size response out of the box, which is why people assume it can't be made pressure-sensitive. It can.
2. Open Brush Studio
Tap your duplicated brush to open Brush Studio. You'll see a list of settings categories on the left, including Taper and Apple Pencil. The layout varies slightly between Procreate versions, but the Apple Pencil tab is where pressure lives.
3. Set pressure response in the Apple Pencil tab
Open the Apple Pencil tab. Under the pressure section, you'll find sliders that control what pressure changes:
- Size: Harder pressure makes a wider stroke. This is the setting for inking, calligraphy, and expressive line work. A community-recommended starting point is roughly 70%, then adjusting by feel.
- Opacity: Harder pressure makes the stroke more solid. This suits pencil, charcoal, and soft shading.
Pick one to start. A line brush often needs just Size. A shading brush often needs Opacity.
4. Test with a real stroke, not a scribble
Draw a stroke that starts light, builds to heavy, and returns to light. This is the test that exposes problems with the response curve. Repeat it quickly and slowly, and test on the canvas at the size you actually plan to work.
Fine-Tuning the Feel
Separate Taper from pressure
Taper and pressure are different systems. Taper shapes the start and end of a stroke regardless of how hard you press. If you raise a slider and notice only the end of the stroke thinning, you're probably looking at taper behavior, not pressure response. Open the Taper tab, and either reduce it while you diagnose pressure or use it deliberately for brush-pen-style ends. Forum advice on stubborn size response often boils down to disabling taper or softness while you test.
Adjust the response curve
The global pressure curve lets you shape how input maps to output:
- A curve that rises steeply at the start makes light touches leave a visible mark. This works well for sketching and pencil-style brushes where you want mid-tones without leaning hard.
- A curve that stays low at first and rises late demands firm pressure for visible results. This gives fine control for delicate line work but feels sluggish for sketching.
Add a node in the middle of the graph and nudge it a little at a time. Small moves have large effects.
Use stabilization carefully
Stabilization settings smooth wobble but can add lag that makes pressure feel disconnected from the stroke. If your brush feels "late," lower stabilization before blaming the pressure curve.
Save and name your variants
Once it feels right, rename the brush clearly, such as "Ink – Pressure Size 70" or "Graphite – Pressure Opacity."
Adjusting the Global Pressure Curve
Open the wrench menu, go to Prefs → Pressure and Smoothing, and you'll see the graph that applies to all brushes. Dragging the curve changes how every brush interprets your input.
A few practical notes:
- Procreate's own guidance is to avoid changing the global curve unless you need to. Brushes are designed to work for most cases, and edits can produce unexpected results.
- If you use it, make small changes. A slightly steeper start helps people who find they must press too hard for any mark.
- To disable pressure sensitivity globally, you can drag the upper point to the far left so the line becomes vertical. That makes brush thickness depend only on the size slider.
- If something goes wrong, scroll to the bottom of the menu and tap Reset all. This resets the settings in this menu.
Troubleshooting Common Problems
Pressure only works one way (thicker, never thinner). Check Taper first. Then lower stabilization and test with slower strokes. Reset the brush to defaults and reapply one change at a time.
Nothing responds to pressure. Confirm the pressure sliders are above zero in Brush Studio, and that the global curve hasn't been flattened. Check that the brush you're using is the one you edited, not the original.
Fast strokes feel inconsistent. iPad input can feel different from a desktop tablet on quick strokes. Adjusting the curve often helps.
You're using a non-Apple stylus. Pressure needs a smart stylus that Procreate supports. Cheap capacitive styluses draw but send no pressure data. If your stylus doesn't send pressure, there's a workaround: hold the Size or Opacity slider with your non-drawing hand and vary it while you draw. It's clumsy, but it fakes dynamic width for a stroke.
Why This Matters for Motion and VFX Work
Pressure-sensitive brushes are a practical tool in motion pipelines. A few common uses:
- Frame-by-frame animation: Expressive ink and pencil lines give hand-drawn sequences character that vector shapes struggle to match.
- Textures and elements: Painted grain, smoke shapes, dirt, and mattes can be drawn quickly and exported for compositing in After Effects, Nuke, or Blender.
- Style frames and boards: Loose, pressure-driven sketches communicate mood and composition before heavier 3D or animation work starts.
Keep your canvas at a resolution that matches your delivery target, since a brush that looks good on a small canvas can look soft once scaled in a comp. Export layers or flattened frames depending on how much you'll rework them in compositing.
Quick Checklist
- Duplicate a brush and open Brush Studio.
- In the Apple Pencil tab, raise the Size or Opacity pressure sliders.
- Check Taper and stabilization so they don't mask the pressure response.
- Tune the response curve in small steps and test with light-heavy-light strokes.
- Change the global curve only if your hand or stylus needs it, and keep Reset all in mind.
- Save and name the brush so you can reuse it.
Treat each brush as a small instrument: one or two pressure targets and a curve that matches how you naturally draw. That's what separates a brush that feels alive from one that fights you.