How to Make a Picture Opaque in Procreate
StyleFrame Team7 min read
To make a picture opaque in Procreate, open the Layers panel, tap the "N" next to the picture's layer, and drag the Opacity slider to 100%. You can also tap the layer with two fingers and slide right on the canvas until the readout hits 100%. If the image still looks see-through at 100%, the cause is usually a blend mode, a group setting, or transparent pixels in the source file, and each has its own fix below.
What "Opaque" Means in Procreate
Opacity describes how visible a pixel is. At 100% a pixel is fully visible, and at 50% it is half see-through. Procreate lets you control this at three levels: the brush, the whole layer, or a selection on a layer.
When you bring a photo into Procreate, it lands on its own layer. "Making it opaque" therefore means raising that layer's opacity to 100%, or fixing whatever is keeping it from reading as solid. The layer opacity slider is the first thing to check. If it is already at 100%, jump to the troubleshooting section.
Method 1: The Layer Opacity Slider
This is the most reliable method because it is non-destructive. You can change the value as often as you like without altering any pixels.
- Tap the Layers icon in the top right.
- Find the layer holding your picture.
- Tap the small letter to the right of the layer name. It reads "N" by default, for Normal blend mode.
- Drag the opacity slider to the right until it reads 100%.
The same panel holds the blend mode list, so you can confirm at a glance that the layer is set to Normal.
Method 2: The Two-Finger Tap Gesture
This is the faster route once it is in your hands.
- Open the Layers panel.
- Tap the picture's layer with two fingers at once. An opacity bar appears at the top of the screen.
- Slide a finger right on the canvas to increase opacity, or left to decrease it.
- Watch the percentage shown beside the word "Opacity" and stop at 100%.
This also adjusts only one layer at a time. It is a good way to scrub opacity while you watch the image react, which is handy when you are matching a reference plate or balancing a collage of several photos.
Method 3: Adjustments > Opacity
Procreate also has Opacity under the Adjustments menu. It works as a full-screen interface:
- Select the picture's layer.
- Tap Adjustments > Opacity.
- Slide your finger left or right anywhere on the canvas. A bar at the top shows the current value, starting at 100%.
- Tap the Adjustments icon again, or choose another tool, to commit. Use Cancel to exit without applying anything.
Four buttons along the bottom handle cancel, undo, redo, and reset. Treat this method with some caution. Unlike the layer slider, it applies the change once you commit it, so you cannot revisit and re-tune it later. For anything you might want to adjust again, use the layer slider.
Changing Opacity on Part of the Picture
If only a region of the image needs to be more solid, use a selection:
- Tap Selection and choose a method.
- Make your selection.
- Open Layers and tap the layer with two fingers.
- Slide right on the canvas to raise the opacity of the selected area, or left to lower it.
Selection opacity is also a committed change. Once you exit, it is applied, and you cannot adjust it repeatedly the way you can a layer slider. If you may want to revise it, duplicate the layer first or keep the original hidden below.
Why Your Picture Still Looks Transparent at 100%
When the slider is maxed and the image still looks ghosted, work through this checklist.
The blend mode isn't Normal
Tap the "N" (which may show a different letter or abbreviation if a mode was applied) and check the blend mode list. Modes like Multiply, Screen, or Overlay change how the layer interacts with what is underneath, so it can look washed out or translucent even at full opacity. Set it back to Normal.
The layer is inside a group with reduced opacity
Groups carry their own opacity. If the picture sits in a group set to 70%, the picture can never exceed that. Open the group's settings and raise it to 100%.
The layer is clipped to something else
A layer set as a clipping mask only shows where the layer beneath it has pixels. If the base layer is partially transparent or smaller than your picture, parts of the image will vanish or look faint. Release the clipping mask or fix the base layer.
The source image has transparent or semi-transparent pixels
This is the most common cause with PNGs, logos, and cutouts. The layer opacity slider scales whatever alpha already exists, but it cannot create solid pixels from transparent ones. If the original has soft or partially transparent areas, those stay see-through no matter how far you push the slider.
You're painting, not adjusting a layer
If the problem is a brush stroke rather than an image, check the brush opacity slider (the lower slider in the sidebar). Many brushes also respond to Apple Pencil pressure, so a light touch can make strokes look thin even with the slider at maximum.
Making Semi-Transparent Pixels Solid
If your picture has an alpha channel you want to eliminate, you have a few options.
- Put a solid layer behind it and merge. Create a new layer beneath the picture, fill it with a color, then use Merge Down on the picture layer. The result is a single fully opaque layer. Choose the fill color deliberately, since it will become part of the image wherever there was transparency.
- Duplicate and merge to build density. Duplicating a partly transparent layer and merging the copies stacks the alpha, which makes soft areas denser. It can also harden edges and change feathering, so inspect the result at 100% zoom.
- Use Alpha Lock for recoloring. Alpha Lock keeps painting confined to existing pixels. It helps you recolor a shape, but it won't fill in missing alpha.
Keep a copy of the original layer hidden before you flatten anything. Merges cannot be reversed once you move on from them.
Exporting an Opaque Picture for Motion Work
Many artists in motion pipelines use Procreate for quick paint-overs, textures, and style frames, then bring the result into After Effects, Premiere Pro, Blender, or Nuke. A few habits prevent surprises:
- Hide the paper color layer if you need alpha. Procreate's Background color layer is part of the canvas. If it stays visible, a PNG export will be fully opaque. Turn it off if you want transparency.
- Export format matters. PNG preserves transparency, while JPEG flattens it. PSD export keeps layers, which lets you adjust opacity in After Effects instead of baking it in.
- Check your own layer opacity before exporting. A layer left at 80% will export at 80% in a flattened image, which shows up later as a faint, unexplained transparency in the comp.
- Check edges in your compositor. If you export with transparency and see dark or light fringes, review how your compositing application interprets the alpha channel for that file.
Setting an image to opaque in Procreate is a small step, but it is worth confirming before you hand off, because correcting it in the comp usually means going back to the source.
Quick Reference
FAQ
Can Procreate make an image more than 100% opaque? No. 100% is the ceiling. To make a faint image look denser, you need to deal with its alpha, for example by merging it over a solid layer.
Does changing layer opacity damage my image? No. The layer slider is non-destructive, and you can return to 100% at any time. The Adjustments > Opacity tool and selection opacity are applied when committed.
Why does my exported picture look transparent? Usually a layer or group was left below 100%, or the canvas background was hidden and the export retained transparency. Check both before you export.