How to Make a Picture Look Like a Drawing Procreate
StyleFrame Team7 min read
To make a picture look like a drawing in Procreate, import the photo, duplicate it, desaturate the copy, duplicate that, and set the top layer's blend mode to Divide. Then apply a Gaussian Blur to that layer until pencil-like lines appear. Finish with a Curves adjustment to set the contrast, and add color back with a duplicated color layer on Overlay if you want a tinted sketch. The process is quick and gives you a usable sketch base for stills, which you can also use as a starting point for moving footage.
Method 1: The Divide-blend pencil sketch
This is the most reliable route. It uses only built-in adjustments and blend modes, and you can tweak every stage.
- Insert the photo. Open the Actions menu (wrench), choose Add, then Insert a Photo. Fit it to the canvas.
- Duplicate the layer. Swipe left on the photo layer and tap Duplicate. Hide the bottom layer so you keep a clean original.
- Desaturate the copy. Open Adjustments (magic wand), choose Hue, Saturation, Brightness, and drag Saturation to zero. A small brightness nudge here can help flat or dark images.
- Duplicate the grayscale layer. You now have two identical black-and-white layers.
- Set the top layer to Divide. Tap the "N" on the layer thumbnail, and find Divide in the blend mode list. The canvas will turn almost entirely white. That is expected.
- Blur the Divide layer. Go to Adjustments, then Gaussian Blur, and choose Layer as the target. Drag across the screen. As the blur increases, edges reappear as soft graphite-like lines. Low values give thin, faint lines. Higher values give heavier shading and more of the original tone.
- Merge down and adjust. Merge the Divide layer into the grayscale layer beneath it, then open Curves. Pull the black point to the right to deepen the lines and the white point slightly left to clean the paper tone. Go gently, since pushing too far inverts the look or crushes the detail.
Blur amount is the main creative control. Roughly 5 percent produces crisp, technical lines. Values around 10 to 15 percent give a looser, more shaded pencil feel. The right number depends on your image resolution, so judge by eye rather than copying a figure.
Method 2: The Color Dodge variant
An older technique reaches a similar result by inverting rather than dividing. It is worth knowing because it behaves slightly differently, with softer tonal transitions.
- Insert the photo, duplicate it, and desaturate the duplicate.
- Duplicate the grayscale layer again.
- On the top copy, open Curves and drag the curve "downhill" so the image inverts to a negative.
- Set that inverted layer's blend mode to Color Dodge. In the blend list, it sits under the Lighten tab. The canvas goes white.
- Apply a Gaussian Blur to the inverted layer until the line drawing appears.
Some users report a yellow or tinted result instead of white. If that happens, check that the layer you inverted was desaturated first. If you only see a high-contrast black-and-white photo with no linework, the blur is either missing or applied to the wrong layer. Check which layer is selected before you adjust the blur.
Adding color back for a colored drawing
A pure grayscale sketch can look sterile. To get a colored-pencil or marker feel:
- Keep the original color photo as the bottom layer.
- Hide the intermediate grayscale layer, or delete it if you're happy with your line pass.
- Duplicate the color layer and drag the copy to the top of the stack.
- Set that top copy to Overlay.
- Optionally, paint over the overlay with a plain, solid brush such as the Monoline in the Calligraphy set.
- For stronger color, duplicate the overlay layer.
A second approach keeps the line art separate. Set your finished line layer to Multiply so the white paper drops out and only the dark lines remain. Create a new layer underneath and paint or fill color there. Multiply is the standard trick for scanned inked art as well, since it separates black lines from a light background without any masking. If your paper is off-white or grainy, push the layer's brightness and contrast with Curves before switching to Multiply.
Troubleshooting common problems
- Everything is white. The Divide or Color Dodge layer hasn't been blurred yet. The blur reveals the lines.
- Lines look too faint. Lower the blur, then tighten Curves. Pulling the black point right strengthens darks.
- Result looks like a washed-out photo. Your source image is probably low in contrast. Add a Curves or Brightness/Contrast pass to the grayscale layer before you duplicate it.
- Output is soft and fuzzy. This approach is a tonal trick, not true edge detection. Photoshop's Find Edges filter produces sharper contours. If you need crisp, clean outlines, a dedicated edge filter or a hand-traced pass over the sketch will beat any blur-based method.
- Colors feel muddy. Reduce the opacity of the Overlay layer or swap Overlay for Soft Light.
Where Procreate stops being the right tool
Procreate is excellent for stills and illustration. For professional motion work, though, it has clear limits:
- No video pipeline. Procreate is built around single canvases and brushwork, and it is not a tool for restyling live-action clips.
- Per-frame inconsistency. If you exported frames and ran each one through the same recipe, the blur-based lines would respond to noise, grain, and lighting changes, and the result would flicker.
- Manual and non-parametric. Every pass is applied destructively unless you carefully manage layers.
That doesn't make Procreate less useful as a look-development sketchpad. It's a fast place to test what style you want, then rebuild or extend it elsewhere.
Reproducing the look in video software
A similar stack can be rebuilt in video compositing software such as After Effects.
- Duplicate your footage layer.
- Desaturate the top copy.
- Duplicate again and invert the top copy.
- Set the inverted layer's blend mode to Color Dodge, or use a Divide-style setup with the grayscale layer duplicated and blurred.
- Add a Gaussian blur to the inverted layer.
- Use a Curves-style adjustment for the final contrast.
Add a paper texture on Multiply. You will still see some flicker with noisy footage, so denoise first or apply a light temporal smoothing pass.
Where Styleframe fits when you need more than a filter
Blur-and-blend tricks give you a generic pencil look. When a project needs a specific drawn style, such as a particular ink line weight, a hatching pattern, or the feel of a reference illustration, filters hit a ceiling. That's where an AI tool built for artistic control can complement your existing workflow.
is an AI video and motion tool designed around reference-driven control rather than one-click output. It uses your reference images and video clips to guide the drawn look, whether that's a frame you sketched in Procreate or an illustration in the target style.
A practical workflow for a motion designer might look like this:
- Prototype the look on a still in Procreate using the Divide method above, or hand-finish a keyframe.
- Use that frame as a style reference in Styleframe on your footage or keyframes.
- Export the result and bring it into your compositing software for grading, paper textures, and final delivery.
The point is control: your reference images and clips drive each generation, so you stay the art director rather than hoping a black box lands the look.
Choosing the right approach
- Quick still reference or sketch base: Procreate's Divide method is fast and free of extra tools.
- Colored, painterly stills: Add the Overlay color layer and a plain brush pass, or paint under a Multiply line layer.
- Procedural look on footage: Rebuild the stack in video compositing software such as After Effects.
- A specific illustrated style across a shot: Use reference-driven style transfer in Styleframe, then composite the result in your compositing software.
Start with the Procreate recipe to find the line weight and tone you like. Once you know the look, you can decide whether a filter stack is enough or whether the shot needs a style-driven pass.