How to Make a Layer Transparent in Procreate
StyleFrame Team7 min read
To make a layer transparent in Procreate, open the Layers panel, tap the "N" to the right of the layer name, and drag the Opacity slider below it to the left. You can also tap the layer with two fingers and slide left on the canvas to lower opacity or right to raise it. Both methods change the whole layer non-destructively, so you can come back and adjust the value later. To make only part of a layer transparent, make a selection first and use the two-finger gesture, which applies a permanent change.
Quick Reference: Opacity Methods in Procreate
Method 1: Use the Layer Opacity Slider
This is the most controlled approach, and the one closest to how you would adjust opacity on a layer in After Effects.
- Tap the Layers icon (two overlapping squares) in the top right.
- Find the layer you want to change. Opacity applies to one layer at a time.
- Tap the small letter to the right of the layer name. It reads "N" by default, which stands for Normal blend mode.
- A panel opens with the blend mode list and an Opacity slider. Drag the slider left to make the layer more transparent, or right to make it more solid.
The setting is non-destructive. The pixels on the layer are untouched, and you can reopen the panel and change the value as often as you like. Tap the "N" and you'll also see the blend modes, which will be familiar if you work with transfer modes in After Effects.
Method 2: Use the Two-Finger Gesture
The gesture is quicker when you're iterating on several layers.
- Open the Layers panel.
- Tap the target layer with two fingers at the same time. The index and middle finger of one hand work well.
- A slider appears at the top of the screen, starting at 100% for a fully opaque layer.
- Slide a finger left across the canvas to lower opacity, or right to raise it.
- Lift your fingers when you reach the value you want.
Two things trip people up. First, you need to tap the layer in the Layers panel, not on the canvas. Second, if two-finger tap is assigned to Undo in your Gesture Controls, a canvas tap will undo a stroke rather than open the slider. Tapping the layer row in the panel avoids that conflict.
How to Make Only Part of a Layer Transparent
Sometimes you want a fade on one region, such as a soft shadow edge or a ghosted shape, without touching the rest of the layer. Procreate handles this through selections.
- Tap the Selection tool and pick a method.
- Make your selection on the layer.
- Open the Layers panel.
- Tap the layer with two fingers at the same time.
- Slide left on the canvas to reduce the opacity of the selected area, or right to increase it.
Leaving this mode commits the change. That makes it a destructive edit: you can undo it right away, but you can't reopen it later and revise the value. Each time you apply it, the result is baked into the pixels.
If you've used the layer opacity slider while a selection was active, note that the slider still affects the entire layer. Only the two-finger gesture respects the selection.
Brush Opacity vs. Layer Opacity
These two controls are easy to confuse, and mixing them up is a common source of "why is my art so faint" questions.
- Brush opacity is the lower slider in the Sidebar. It controls how opaque new strokes are as you paint. It does not change anything already on the canvas.
- Layer opacity controls how visible everything on a given layer is, whenever you set it.
If your strokes look too transparent even with brush opacity at maximum, check your brush settings. The opacity of many brushes responds to Apple Pencil pressure, so a light touch will produce faint marks. Also check whether you're painting on a layer whose opacity is already reduced, or on a clipping mask.
The Older Adjustments > Opacity Tool
Older versions of Procreate included an Opacity option under Adjustments. You tapped Adjustments > Opacity, slid left or right on the canvas to change the value shown in a blue bar, and then committed by tapping the Adjustments icon again or choosing another tool. In current versions, users report that the same function is reached through the two-finger gesture on the layer. If you're following an older tutorial and can't find the Adjustments entry, use the two-finger method above.
Exporting Transparent Procreate Artwork for After Effects
Once your layer opacity is where you want it, the next question for motion work is how it survives export. Results vary by file format, so check the exported file in your compositor.
A practical habit is to leave most opacity decisions to After Effects. Export layers at full opacity, then animate opacity with keyframes in your timeline. Use Procreate's opacity when the transparency is part of the painted look, such as glazing, translucent shadows, or soft overlays.
Troubleshooting Common Opacity Problems
The slider doesn't appear. Make sure you're tapping the layer in the Layers panel with two fingers. If your gesture settings map two-finger tap to Undo, use the "N" method instead.
The whole layer changes when I only wanted a selection. The slider under the "N" is a whole-layer control. Use the two-finger gesture while the selection is active.
I can't change the opacity again later. If you applied opacity to a selection, that edit was destructive. Undo it right away if you can.
Where Styleframe Fits After Your Procreate Work
Procreate is strong for painting and layer-level control of transparency. When you need that artwork to move, the work often shifts to motion tools. Styleframe is an AI video and motion tool built for artists who want control over the result rather than a one-click black box. Every generation is driven by your own reference images, video clips, and keyframes, and iteration is non-destructive, so you can try variations without losing earlier versions.
A few of its tools relate directly to Procreate-based work:
- Frames-to-Video: Use keyframes, such as two paintings exported from Procreate, to drive the motion between them.
- Restyle and Ink-and-Paint: These are reference-driven style transfer tools, so you can apply a painted or inked look from your reference art to footage.
- Remove Background: Isolate a subject from its background when you need a cutout to composite.
- 2D-to-3D and Turntable: Turn a 2D illustration into a 3D result and view it from different angles.
- 4K Upscale: Bring output up to production-ready 4K.
Styleframe exports image sequences, so the results fit into an existing pipeline. You can bring them into After Effects or Nuke and keep compositing, color work, and opacity animation where you already do them. Use Procreate to set up your painted layers and transparency, and use your compositor for final timing and blending.
FAQ
Can I make a layer partly see-through without losing the original? Yes. Use the layer opacity slider, which is non-destructive and stays editable.
What's the difference between making a layer transparent and erasing? Opacity reduces visibility across the layer without removing pixels. Erasing removes pixels permanently.
Is there a shortcut for opacity? The two-finger tap on a layer is the quickest route. Slide left to reduce opacity and right to increase it.