How to Make a Layer Translucent in Procreate
StyleFrame Team7 min read
To make a layer translucent in Procreate, open the Layers panel, tap the "N" next to the layer name, and drag the Opacity slider down. You can also tap the layer with two fingers and slide left on the canvas to lower opacity or right to raise it. Both methods change layer opacity non-destructively, so you can return and adjust the value at any time.
What opacity means in Procreate
Opacity describes how visible a pixel is. A layer at 100% is fully opaque, and one at 50% is half see-through. Procreate lets you control this in three places:
- Brush opacity, which affects the strokes you paint.
- Layer opacity, which affects everything on a layer as a whole.
- Selection opacity, which affects only a selected area of pixels on a layer.
Method 1: The "N" menu in the Layers panel
This is the most explicit method. It also shows the exact percentage, so you can match values across layers.
- Tap the Layers icon (two overlapping squares) in the top right.
- Find the layer you want to make translucent.
- Tap the small letter to the right of the layer name. It reads "N" by default, which stands for Normal blend mode.
- Drag the Opacity slider at the top of the menu to the left to reduce opacity, or to the right to increase it.
The same menu lists the blend modes, so you can change blend mode and opacity in one place. If a layer looks too heavy after you switch it to Multiply or Overlay, this is where you pull it back.
Because you can reopen this slider and change the value as often as you like, this is a non-destructive edit. Your pixels never change, only how strongly the layer shows through.
Method 2: The two-finger tap shortcut
This is the faster way once you're comfortable in the interface.
- Open the Layers panel.
- Tap the target layer with two fingers at the same time. The index and middle fingers of one hand work well.
- A slider appears at the top of the screen, starting at 100% if you haven't changed it.
- Slide your finger or Apple Pencil left to make the layer more transparent, or right to make it more solid.
- Lift your fingers to finish.
The slider shows a percentage, so you can land on a specific value rather than eyeballing it. One limit applies: you can only change opacity on one layer at a time this way. If you want several layers to fade together, put them in a group and change the group's opacity instead.
Method 3: Adjustments > Opacity
Procreate also has an Opacity option in the Adjustments menu (the magic wand icon). It makes the contents of the active layer more transparent, and it works differently from the layer slider.
- Select the layer.
- Tap Adjustments, then Opacity.
- Slide left or right on the canvas. A blue bar labelled "Slide to adjust" shows the current value, starting at 100%.
- Use the buttons along the bottom to cancel, undo, redo, or reset your changes.
- Tap the Adjustments icon again, or choose another tool, to commit the change.
Treat this as a one-off adjustment rather than a flexible setting. Once you commit, the change is applied, and you can't reopen it later the way you can the layer slider. If you want to keep adjusting a layer's opacity throughout a project, use Method 1 or 2.
Making part of a layer translucent
Sometimes only one area should be see-through, such as a glass highlight, a smoke wisp, or a shadow edge. Procreate handles this with selections.
- Tap Selection and choose a method.
- Make the selection on the layer.
- Open the Layers panel and tap the layer with two fingers.
- Slide left on the canvas to reduce the opacity of the selected area, or right to increase it.
When you exit this mode, the change is applied to the pixels. Like the Adjustments version, it is destructive. You can undo it right away, but you can't revisit the value later.
A safer workflow for selection-based transparency is to duplicate the layer first, apply the change to the duplicate, and keep the original hidden as a backup. If the selected area is one you'll want to tune repeatedly, cut it onto its own layer and use the standard layer opacity slider instead.
Making brush strokes translucent
If you want a translucent look at the painting stage rather than after the fact, lower the brush opacity before you paint.
- Select a brush.
- Drag the lower slider in the sidebar down to reduce brush opacity, or up to increase it.
If your strokes look fainter than the slider suggests, check Apple Pencil pressure. The opacity of many brushes responds to pressure, so even a maximum opacity setting can produce light strokes if you press softly. Pressure settings are a good place to look.
Practical tips for translucent layers
Use clipping masks for contained shading. A clipping mask limits a layer's paint to the shape of the layer below it. It's a clean way to add translucent shadows or highlights that stay inside a form. Lower the clipped layer's opacity to keep the effect subtle.
Combine opacity with blend modes. Opacity alone often looks flat. A glow at 60% on Add or Screen reads very differently from the same layer on Normal. Since both controls are in the "N" menu, it's easy to compare.
Group first, then fade. If a character is built from a dozen layers, lowering each one separately will make overlapping areas show through each other. Put them in a group and lower the group's opacity so the whole figure fades as one unit.
Name layers with their intent. If you hand files to someone else, a layer called "glass 40%" saves time. Opacity values live in the layer settings and aren't visible at a glance in the panel.
Check the result on a contrasting background. A translucent layer looks different over white, black, and mid-grey. Toggle the background color layer to verify the effect holds up where it will be used.
Common problems and fixes
- The slider doesn't seem to do anything. Make sure the right layer is selected. Opacity applies only to the active layer.
- Opacity jumped back to 100% after I exited. If you used the Adjustments menu, make sure you committed the change by tapping the Adjustments icon again rather than cancelling.
- Overlapping shapes show through each other. Merge those shapes onto one layer, or group them and fade the group.
- I can't adjust it again later. That's a symptom of the Adjustments or selection methods. Use the layer-level slider for anything you may revisit.
- Strokes are fainter than expected. Check brush opacity and Apple Pencil pressure, not only layer opacity.
Bringing translucent Procreate layers into a motion pipeline
If you're a motion designer or compositor, Procreate is probably one stop among several. Hand-painted textures, overlays, smoke, glows, and character art often get built on an iPad and then composited elsewhere.
Layer opacity is an easy value to carry through, but it's worth checking each time you hand a file off. Exporting a layered file lets you keep layers separate, so you can adjust their opacity again in your compositing software instead of baking it in. If you flatten or export a single image, the translucency is baked into the pixels and can't be changed downstream. When in doubt, export layers separately, or keep a clean full-opacity version alongside the baked one.
Many motion tools let you animate opacity over time. A practical approach is to paint with full-strength shapes in Procreate and do the fine-tuning of transparency in your compositor, where it can animate.
Quick reference
Final thoughts
For most work, the layer-level slider is the right choice. Open it from the "N" menu or with a two-finger tap, set the value, and revisit it whenever the composition changes. Save the Adjustments and selection methods for cases where you want a local, committed change, and duplicate the layer first so you can go back.