How to Make a Layer Glow in Procreate
StyleFrame Team7 min read
To make a layer glow in Procreate, either use Adjustments → Bloom on that layer, or build the glow manually: duplicate the layer, recolor the copy, apply Gaussian Blur, move it beneath the original, and set its blend mode to Add or Color Dodge. Bloom is the fast route and adds a glow to a layer's brightest areas. The manual method gives you control over glow color, falloff, and layering, so it is the better choice for stylized work.
Before You Start: Set Up the Layer to Glow
A glow only reads when there is contrast. Two things matter before you touch any effect:
- A darker background. Glow is additive light, so it disappears against a bright backdrop. Lower the background layer's brightness (Adjustments → Hue, Saturation, Brightness) or fill it with a deep shade of your palette.
- Isolated elements. Put the object you want to glow on its own layer. Both Bloom and the blend-mode method operate per layer, so a clean separation lets you adjust the glow without touching the rest of the artwork.
Pale shapes are the simplest starting point. A white or near-white shape on its own layer gives you a bright core, which is what real light sources look like: a hot center that falls off into color.
Method 1: Use Bloom on a Single Layer
Bloom is Procreate's built-in atmospheric glow. It works on an entire canvas or a single layer, and it is the quickest path when you want a convincing light bleed without building anything.
- Select the layer you want to affect.
- Tap Adjustments (the magic wand icon) and choose Bloom.
- Choose Layer mode so the effect applies only to the selected layer.
- Slide your finger left or right across the canvas to set the Bloom amount.
At low values, only the brightest pixels emit light. As you increase the amount, the glow spreads into darker areas. Three controls shape the result:
- Transition controls which tones receive the glow. At 0%, all tones bloom. Pushing it right reduces the effect on darks and midtones, so only highlights glow.
- Size sets how far the glow spreads and how soft its edges are.
- Burn adjusts the intensity.
To commit and exit, tap the Adjustments icon again. To apply and stay in Bloom, tap the canvas to open Adjustment Actions and tap Apply.
When Bloom Is the Right Tool
Bloom is a good fit for neon signs, lit windows, embers, screens, and any element where you want glow to follow the brightness already in your pixels. It is less suitable when you want the glow to be a different color from the source, or when you need a tight rim of color around a white core. Bloom responds to luminance, so it won't invent a colored halo for you.
Method 2: The Duplicate, Blur, and Blend Mode Glow
This technique will feel familiar if you have built glows from duplicated, blurred layers with Screen or Add blending in After Effects or Photoshop.
Step 1: Duplicate the Layer
Swipe left on the layer and tap Duplicate. You now have two copies. The top one stays as your bright core. The lower one becomes the colored glow.
Step 2: Recolor the Lower Copy
Select the lower copy, turn on Alpha Lock (two-finger swipe right on the layer), and fill it with the glow color by dragging a color from the color picker onto the layer. Pick something more saturated than you think you need, because blur and blending will dilute it.
Turn Alpha Lock off afterward so the blur can spread beyond the shape's edges.
Step 3: Apply Gaussian Blur
With the colored layer selected, go to Adjustments → Gaussian Blur → Layer and drag across the screen to set the radius. Keep the first blur modest so the color is visible close to the edge of the white core. A tight band of saturated color around a bright center is what sells the effect.
Step 4: Change the Blend Mode
Tap the N next to the colored layer and try one of these:
- Add (Linear Dodge): brightens strongly and tends toward white where layers overlap. Good for intense, hot glows.
- Screen: softer than Add, and less likely to clip. Good for gentle ambient light.
- Color Dodge: stronger and more saturated, but can blow out quickly.
- Overlay: boosts color without raising overall brightness as much, so it works well as a supporting layer.
Step 5: Stack Glow Layers
One glow layer rarely looks right. Duplicate the blurred layer and give the copies different blur radii: a tight blur for a hot halo, a wide blur for atmospheric falloff. One or two Add layers are enough for a soft glow. A more intense look can use a few more, but past roughly five layers you are mostly making the image muddy. Keep the highest-intensity layers near the top of the stack.
Method 3: Paint Light Directly With a Glow Layer
Glow on an object also means light landing on nearby surfaces. A light source should tint what surrounds it.
- Create a new layer above your artwork.
- Set its blend mode to Add or Color Dodge.
- Pick a saturated version of the glow color and paint with a soft brush where the light would fall: the edge of a face, hair, a nearby wall.
- Add small, hard highlights on a separate layer for the brightest points.
This is the step that makes a glow feel integrated rather than pasted on. If you only blur the source, the object looks lit from inside while its environment stays unaffected.
Troubleshooting Common Glow Problems
The glow looks gray or muddy. The background is probably too light, or the glow color is desaturated. Darken the backdrop and push the saturation up on the glow layer.
The core is blown out. Add and Color Dodge clip fast. Lower the layer opacity, switch to Screen, or reduce the number of stacked layers.
The glow has hard edges. The blur was applied with Alpha Lock on, or the radius is too small. Turn Alpha Lock off and increase the blur.
Bloom affects the whole image. You applied it in Pencil mode or did not select the correct layer. Re-open Bloom and confirm Layer mode is active.
The glow shifts color. Blend modes interact with whatever is beneath them. Check which layers sit below the glow, and use a clipping mask or a group to confine the effect.
Taking a Procreate Glow Into a Motion Pipeline
For motion designers, a glowing still is often just the beginning. A few practical notes on moving it into After Effects:
- Keep glows on separate layers. Export layered artwork so each glow sits on its own layer, so you can adjust or animate individual glows in After Effects. Check that blend modes translated correctly.
- Consider rebuilding the glow in After Effects. If the glow needs to pulse, flicker, or react to movement, it is usually more flexible to export the clean, unglowed artwork and use a native glow effect or a blurred, Add-blended duplicate that you can keyframe.
- Export flat versions for reference. A flattened PNG of the finished glow gives you a visual target when you rebuild or match it elsewhere.
Quick Reference: Which Glow Method to Use
Final Tips
Treat glow as light, not as a filter. Start with a bright core, add a saturated near halo, then a wide, soft falloff, and finally let the light tint nearby surfaces. Use Bloom when you want speed and the blend-mode stack when you want control. Whichever you choose, keep each glow on its own layer so you can adjust it later, whether in Procreate, After Effects, or anywhere else in your pipeline.