How to Make a Layer Black and White in Procreate
StyleFrame Team7 min read
To make a layer black and white in Procreate, select the layer, open Adjustments, choose Hue, Saturation, Brightness, and drag the Saturation slider fully to the left. This is destructive, so duplicate the layer first if you want to keep the color. For a more tonally accurate result, duplicate the layer, place a white layer between the copies, and set the top copy to the Luminosity blend mode.
Quick answer: three ways to desaturate a layer
The Adjustments tools apply their effect directly to the pixels of the selected layer. Keep that in mind when choosing a method.
Method 1: Hue, Saturation, Brightness
This is the quickest route and the one most tutorials start with.
- Tap the layer you want to convert in the Layers panel so it is active.
- Open the Adjustments menu from the top toolbar.
- Choose Hue, Saturation, Brightness.
- At the bottom of the screen, choose Layer (this applies the change to the whole layer; Pencil lets you paint the effect in locally).
- Drag the Saturation slider all the way to the left.
- Lift your finger or Pencil to commit, then tap the canvas or the Adjustments icon to close the tool.
The layer is now neutral grey, with every pixel's red, green, and blue values equal. Because the change is baked in, duplicate the layer before you start if you might need the color again. Swipe left on the layer and tap Duplicate, then hide the original.
Tune the contrast afterward
Pure desaturation often looks flat, especially when saturated hues of similar brightness collapse into the same grey. Open Adjustments > Curves on the same layer and pull the curve into a gentle S-shape: lower the shadow end, raise the highlight end, and shift the midtones as needed. Make sure Gamma is selected in Curves, which is what you want for a neutral black-and-white result. Brightness moves can also be done in the same HSB panel, but Curves gives you finer control.
Method 2: The Luminosity blend technique
Plain desaturation treats all colors in a fairly generic way, and some hues (a saturated orange, for example) can land darker or lighter than you expect. A Luminosity-based conversion maps the image's brightness to grey and often looks closer to a photographic black-and-white. It also uses only layers and blend modes, so you can preview the result before committing.
- Duplicate the layer you want to convert.
- Add a new empty layer, fill it with white (drag the color from the Color panel onto the layer), and move it between the original and the duplicate.
- Select the top duplicate, tap its N icon, scroll to the bottom of the blend mode list, and choose Luminosity.
- Check the result. If you are happy, pinch the three layers together to merge them into one grey layer. If you need a flattened version for comparison, use Actions > Add > Copy Canvas.
The white layer matters because Luminosity applies the top layer's brightness to the colors beneath it. With white underneath, the result is a neutral grey rather than a tinted version of the original. Until you merge, the stack is still editable: you can hide the Luminosity copy at any time and your color layer is untouched.
Be realistic about the difference between methods. One forum user who tested both reported that the Luminosity approach and the Saturation slider produced the same grey value for the same orange sample, so you should not expect dramatic differences on every image. Try both on your artwork and keep whichever reads better.
Method 3: A non-destructive greyscale check layer
Sometimes you do not want a black-and-white layer at all. You want to judge values while painting in color. A toggleable overlay does this without modifying anything.
- Create a new layer at the very top of the stack.
- Fill it with a mid-grey (the Values tab in the Color panel or the center of the Disc picker gets you to 50%).
- Set the layer's blend mode to Saturation (you can also try Color).
- Toggle the layer's visibility to flip between color and greyscale views.
Procreate forum members recommend this for value checks. Note that it is a preview and not a pixel-accurate conversion: forum users who compared it with the Saturation slider found that perceived value shifts happen with both. Treat it as a quick read on composition and contrast, then use Method 1 or 2 when you need real grey pixels.
Two other value-checking tricks work outside the layer stack:
- System color filter: In iPadOS Settings > Accessibility > Accessibility Shortcut, enable Color Filters. Triple-pressing the top button then toggles greyscale across the whole screen, in any app. Triple-press again to return to color.
- Grey reference: Convert your reference image to greyscale before importing it into the Reference Companion. Forum users have requested a greyscale toggle there, which was not available at the time.
Keeping a pop of color
If you want a greyscale layer with selected areas still in color, use the original as a safety net.
- Keep the original color layer at the bottom and place the greyscale version above it.
- Select the greyscale layer.
- Either use Selection (Automatic mode) to pick the region you want to reveal and cut it from the grey layer, or take the Eraser and rub out those areas directly.
- The color layer beneath shows through the holes.
Procreate cannot convert a flattened grey image back to its original colors, so always keep that color layer. Instead of deleting the grey pixels, you can also add a layer mask to the grey layer and paint in black, which keeps the reveal editable.
Common problems and fixes
The Saturation slider changed nothing. Make sure a pixel layer is active, not a group. Adjustments work on one layer at a time, so merge or flatten the group first, or apply the adjustment to each layer inside it.
The image looks flat. Add a Curves adjustment or try the Luminosity method. Hues with similar brightness lose separation when the color goes away.
I only wanted to desaturate part of the layer. In the HSB panel, switch from Layer to Pencil and paint the effect where you want it, or make a selection first so the adjustment is limited to that region.
I need the color back. Undo with a two-finger tap, or restore from the duplicate you hid earlier. Otherwise, the original color information is gone.
Taking Procreate artwork into After Effects
If your Procreate art is headed to a motion pipeline, think about where the black-and-white conversion should live. Since Procreate bakes adjustments into pixels, a desaturated layer is a one-way decision.
A more flexible approach for animation work:
- Keep the color version as the source and apply the black-and-white look in your compositing software, so you can animate the transition, mask it, or change the look later.
- If you do bake the conversion in Procreate (for example, the Luminosity method for a particular tonal mapping), save that as a separate layer or file next to the color original.
That keeps your look decisions revisable at comp time instead of locked at paint time.
Where Styleframe fits
Desaturating a layer is a simple operation, and you do not need an AI tool for it. Styleframe may be useful when your Procreate work moves from a flat conversion to a stylistic treatment across moving shots. The compositing stays where you already do it, and Styleframe handles the generative steps you want to direct.
Summary
For a fast result, use Adjustments > Hue, Saturation, Brightness and slide Saturation to zero. For better tonal fidelity, use the duplicate-white-Luminosity stack and merge when satisfied. For checking values mid-paint, use a mid-grey layer set to Saturation or the iPad's Color Filters shortcut. In every case, duplicate the layer first and keep your color source, especially if the artwork is going to After Effects, where the black-and-white look is better applied non-destructively.