How to Make a Heart in Procreate
StyleFrame Team7 min read
Procreate has no built-in heart shape, so you build one. The fastest clean method is to turn on a vertical Symmetry drawing guide with Drawing Assist, draw one half of the heart, and fill it with ColorDrop. For a geometrically exact heart, rotate a square 45 degrees, attach two circles to its upper edges, merge the layers, and fill. Either way, export a transparent PNG or a layered PSD if the heart is headed into After Effects.
Which Method Should You Use?
All three produce a raster heart. Procreate is not a vector tool, so decide on your final resolution before you start. This matters most when the heart will be scaled in a composition.
Set Up the Canvas First
Create a square canvas, such as 4096 × 4096 px, for any heart you plan to scale in motion.
Leave a margin around the heart. If you later animate a pulse or scale-up, a tight crop forces you to re-export. Keep the background layer hidden if you want transparency.
Method 1: Draw a Heart with the Symmetry Guide
This is the standard approach, and it works well because you only have to get one lobe right.
- Tap the Actions icon (wrench), go to Canvas, and turn on Drawing Guide.
- Tap Edit Drawing Guide, choose Symmetry, and open Options.
- Set the axis to Vertical and turn on Drawing Assist. Tap Done.
- Add a new layer, tap it, and make sure Drawing Assist is enabled for that layer. Without this, the mirroring won't apply.
- Pick a monoline or Studio Pen brush. Start at the center top, where the two lobes meet in a dip. Sweep out and over in a rounded curve, then bring the line down toward the bottom point on the center axis.
- Everything you draw on one side mirrors to the other. Close the shape by meeting the guide line at the bottom.
- Drag a color from the Color wheel into the shape to fill it with ColorDrop. If the fill leaks, raise the Color Fill Threshold (hold the drop until the threshold bar appears) or close small gaps.
Tips for a better curve
- Draw slowly and let StreamLine smooth the stroke. Raise it in the brush settings if the curve wobbles.
- Keep the top dip shallow. A deep dip makes the heart look like two separate bulbs.
- If the shape feels lopsided, undo and redraw rather than nudging nodes. Procreate has no anchor points to edit on raster strokes.
Method 2: Build a Precise Heart from a Square and Two Circles
If you need a heart that looks geometrically exact, construct it the way a vector artist would.
- Turn off Drawing Assist and add a new layer. Use the Selection tool in Rectangle mode to draw a square, then fill it by dragging a color into it.
- Open Transform (the arrow icon), use Uniform mode, and rotate the square 45 degrees. Turn on Snapping so the rotation locks at clean angles. The square is now a diamond.
- On a new layer, draw a circle with the brush, hold at the end of the stroke until QuickShape snaps it, and tap Edit Shape to force a true circle. Fill it with the same color.
- Use Transform to scale the circle until its diameter matches one side of the diamond, then position it so it sits centered on the diamond's upper-left edge.
- Duplicate the circle layer, flip it horizontally (Transform > Flip Horizontal), and move it to the upper-right edge.
- Group or merge the three layers. Check the join where the circles meet the diamond; these are the places an imperfect overlap shows.
This construction gives you a symmetrical heart with a clean point at the bottom. It's also easier to hand off to another artist, because the geometry is explicit.
Use Alpha Lock for easy recolors
Once the layers are merged, enable Alpha Lock on the heart layer. You can then paint any color or gradient over it without spilling outside the shape. For shading, add a layer above, set it as a Clipping Mask, and paint highlights and shadows there. That keeps your base shape untouched.
Method 3: A Quick Monoline Heart
For lettering, stickers, or a handwritten feel, skip the fill:
- Choose a monoline brush from the Calligraphy set.
- Draw the left lobe and the downward stroke in one motion, then lift and draw the right side as a mirror.
- Or draw the whole outline in a single continuous stroke, starting at the bottom point and looping up through both lobes.
A single-stroke heart suits line-draw animations later, where you want a path that reads as continuous. Turn on StreamLine and take your time; sketchy hearts read as intentional only when the line weight is consistent.
Clean Up and Refine
- Fix jagged edges. Zoom in and use the Smudge or Eraser with a hard brush to trim stray pixels. Pixelated edges become obvious after scaling in a composition.
- Check for gaps. If ColorDrop left a fringe of unfilled pixels along the edge, fill again with the threshold raised, or paint over the line on the same layer.
- Name and organize layers. Name the heart, shading, and highlight layers clearly.
- Consider a layer for each element. If you'll animate the outline, fill, and highlight separately, keep them on separate layers rather than merging.
Export a Heart for After Effects and Other Tools
Your export format depends on what you do next.
- Transparent PNG. Hide the background color layer, then go to Actions > Share > PNG. This is the simplest option for a single flat heart.
- Layered PSD. Use this if you want to animate the fill, outline, and highlights independently.
- Not a vector. The heart you draw is a raster image. If it needs to scale infinitely, rebuild it with the Pen tool in After Effects or Illustrator, or use Illustrator's Image Trace on a high-contrast PNG. For simple hearts, redrawing the shape with a few Bézier points in a shape layer is often faster and cleaner than tracing.
If you only plan to scale the heart modestly, a large raster with clean edges holds up. Create it at a size well above your delivery resolution.
Common Problems and Fixes
The heart is lopsided. Check that Drawing Assist is enabled on the active layer, and that the symmetry axis sits at the canvas center. If you moved the guide, reset it.
The two lobes don't meet cleanly. Draw the center dip first, then work outward. Starting from the outside tends to leave a gap at the join.
ColorDrop floods the whole canvas. The outline has a gap. Zoom in, close the gap, and try again, or select the shape with the Selection tool and fill that selection instead.
Edges look soft after export. Export at the full canvas size and avoid scaling up in the composition. If the heart must be larger, redraw or use the geometric method on a bigger canvas.
FAQ
Is there a heart shape in Procreate? No. QuickShape snaps rough shapes into clean ones, but there is no heart preset. Use the symmetry method or the square-and-circles method.
Can I make a heart without Drawing Assist? Yes. Draw the left half, duplicate the layer, flip it horizontally with Transform, and merge the two halves. This is useful if you need to adjust each side independently.
What's the best brush for a clean heart? A monoline brush for outlines, or Studio Pen for filled shapes. Use a hard-edged brush when you want crisp edges that scale well.
How do I make the heart transparent for video? Hide the background color layer and export as PNG, or export a PSD if you want to keep layers separate.
Can I animate the heart in Procreate? For anything involving easing, expressions, or compositing, export the heart and animate it in After Effects.