How to Make a Good Blending Brush in Procreate
StyleFrame Team7 min read
To make a good blending brush in Procreate, duplicate a soft, textured brush and turn on Wet Mix in Brush Studio. Then tune Dilution, Charge, Attack, Pull, and Grade until the brush drags existing color instead of laying down new paint. Finish by shaping the grain and mapping Apple Pencil pressure to the blend strength. Test it on a gradient and a rough painted shape before you trust it on real work.
Blending brush vs. smudge tool
Procreate gives you two ways to blend, and the difference decides how you build the brush.
The Smudge tool sits in the top-right toolbar, just to the right of the Brush tool. It borrows the shape and texture of any brush in your library and pushes the pixels already on the layer. It never adds color. Each brush also has a Smudge value under General in Brush Studio, from 0% to 100%. At 0% there's no smudge effect.
A blending brush is a regular painting brush with Wet Mix settings that make it pick up and mix underlying color while it paints. Because it can deposit a little of your selected color as it moves, you can paint and blend in a single pass. That's why it feels closer to wet oil or gouache than a separate smudge step does.
Procreate doesn't ship a preset labeled "blender," but some brushes use Wet Mix, and Turpentine in the Artistic set is one example. Study it first. Open its settings and watch how the sliders change its behavior.
Start from the right base brush
Never edit a stock brush in place. Swipe left on a brush, tap Duplicate, and rename the copy something obvious like "Blend_Soft_v1". Keep the original so you can always compare.
Choose a starting point that matches the look you want:
- Soft, airbrushed transitions: start from a soft airbrush or similar low-texture brush.
- Painterly, visible bristle movement: start from a gouache, oil, or Turpentine-style brush.
- Charcoal or pencil smearing: start from a grainy pencil or charcoal brush.
The base matters more than people expect, because its shape and grain survive every Wet Mix change you make later.
Dial in the Wet Mix settings
This section does most of the work. Open Brush Studio, find Wet Mix, and adjust these sliders. Change one at a time and make a few test strokes after each change.
Dilution
Dilution controls how much of your selected color the brush puts down. Near zero, the brush becomes colorless and only moves existing paint, which makes it behave like a smudge brush. Higher values add more of your active color.
For a pure blender, start low. For a paint-and-blend brush, raise it until new color reads clearly but doesn't overpower what's underneath.
Charge
Charge sets the amount of color or effect the brush has at the start of a stroke.
Attack
Attack sets the amount of color or effect as the stroke continues. Pair it with Charge to decide whether a stroke starts strong and tapers, or stays even from end to end. Even strokes usually blend more predictably, so keep Attack and Charge in a similar range at first.
Pull
Pull sets how strongly existing colors get dragged across the canvas. High Pull produces long, streaky smears that follow your stroke direction. Low Pull keeps the mixing local and short. Skin gradients and soft skies usually want lower Pull. Dramatic painterly smears want higher.
Grade
Grade smooths the brush effect. Raising it softens the visible texture of the blend. Lowering it keeps more of the grain visible. If your blends look too digital or too noisy, check Grade before anything else.
Shape, grain, and stroke path
Wet Mix decides how color moves. Shape and Grain decide what that movement looks like.
- Spacing: Lower Spacing makes strokes continuous and smooth. If you see beading or stepping in a stroke, tighten Spacing.
- Shape: A soft, round shape blends cleanly. A shape with built-in noise or bristle detail gives more painterly results.
- Grain: Subtle grain keeps the blend from looking airbrushed and plastic. Heavy grain can interrupt the smooth transition.
Another tip from artists who've struggled with streaky results: check whether your brush is a glazed brush. Glazed brushes build up in opaque layers like a glaze and don't blend. If your brush isn't mixing colors, switch to a brush that uses Wet Mix and recheck.
Map pressure and tilt to the blend
A blending brush feels good when it responds to your hand. In the Apple Pencil settings:
- Connect pressure to size modestly, so light strokes are narrower and controlled.
- Connect pressure to opacity or flow so light touches nudge color and firm touches commit.
- If your Wet Mix settings allow it, tie pressure to the blend strength so a firm press drags paint further.
Keep the pressure curve gentle. A steep curve makes the brush jumpy, which is the opposite of what a blender should be.
Test it before you trust it
Build a quick test canvas and keep it as a template:
- Paint a gradient between two analogous colors, like blue to purple. Blend the seam with long, slow strokes.
- Paint a flat circle and use the brush to soften one edge into the background, mimicking soft shading.
- Lay down rough strokes of light and dark values and try blending them with short, overlapping passes.
- Test at different sizes, since a brush that works at 200px can fall apart at 20px.
Look for streaks, harsh stepping, muddy color shifts, and blur that looks like a filter. If transitions look too blurry, lower Grade. If strokes don't interact, raise Pull or lower the Dilution. If the brush leaves too much of its own color, drop Dilution.
Blending habits that make any brush better
- Use analogous colors for the smoothest transitions. Large hue jumps muddy faster.
- Work with a low-opacity blend on top of base shapes and build gradually, rather than overworking one spot.
- Put shadows on a Multiply layer and highlights on a Screen layer, then blend them into the base so you keep control of each element.
- For a final soft pass, duplicate your layers, merge a copy, apply Gaussian Blur lightly, then erase back the sharp detail around edges and focal points.
Using blended Procreate art in a motion pipeline
If you work in After Effects, Nuke, Cinema 4D, or Blender, a good blending brush earns its place in a few specific jobs: painted textures, matte paintings, style frames, and hand-painted keyframes that set the look for a sequence.
This is where fits. Styleframe is an AI video and motion tool built for artistic control rather than one-click generation. You can bring in a blended Procreate painting as a reference image so footage or frames pick up the brushwork and color transitions you painted.
Styleframe doesn't replace the painting step. The quality of your blending brush still determines how convincing the reference looks, so spend time getting the brush right first.
A starting recipe to adapt
Treat these as starting points, not fixed values, since every base brush responds differently:
- Duplicate a soft textured brush and rename it.
- Turn on Wet Mix. Set Dilution low to moderate.
- Set Charge and Attack in a similar range for even strokes.
- Start Pull in the middle and adjust toward longer or shorter drags.
- Raise Grade until the texture looks smooth but not plastic.
- Tighten Spacing and map pressure to opacity or blend strength.
- Test on the gradient, circle, and rough-value canvas, then adjust one slider at a time.
Save versions as you go. A small library of two or three blenders, such as a soft one, a painterly one, and a grainy one, covers most of what you'll need.